Coban GPS102B Manual de usuario
1
GSM/GPRS/GPS TRACKER
MANUAL
Preface
Thank you for purchasing the tracker. This manual shows how to operate the
device smoothly and correctly. Make sure to read this manual carefully before
using this product. Please note that specification and information are subject to
changes without prior notice in this manual. Any change will be integrated in
the latest release. The manufacturer assumes no responsibility for any errors
or omissions in this document.
2
1. Summary
Working Based on existing GSM/GPRS network and GPS satellites, this
product can locate and monitor any remote targets by SMS or internet.
Specifications
Content
Specs
Dim.
63mm x 46mm x 21mm
Weight
41g
Network
GSM/GPRS
Band
850/900/1800/1900Mhz
GSM chip
MT6261
GPS chip
Ublox 7020
GPS sensitivity
-159dBm
GPS accuracy
5m
Time To First Fix
Cold status 45s
Warm status 35s
Hot status 1s
Work voltage
5V
Storage Temp.
-40°C to +85°C
Operation Temp.
-20°C to +55°C
Humidity
5%--95% non-condensing
Main functions
·GSM quad-band frequency;
·Real time tracking by SMS/GPRS
·Low battery alarm;
·Geo-fence alarm ;
·move alarm
·SOS alarm ;
3
·Monitor (optional)
·Vibration alarm (optional)
·Add Smart sleep save power Mode
·Add GPX history route record, can check record in Google map
·Add AGPS function,receive GPS signals faster
·Add built-in storage memory
·Add WATERPROOF and dust proof
·patented product
2.Led indicator status
LED INDICATOR STATUS
MEANING
RED LED continuously work
Charging
RED LED not lit
Fully charged
Green LED Flashing
Success get GSM signal
Green LED continuously lit
Searching GSM signal
3. Notices:
1).GPS tracking can be worked outdoor. Must have mobile phone gsm signal
and have GPS signal, can block GPS satellite signal when there are metal
or building above the GPS tracker
2).Please make sure GSM SIM card(2G GSM network or compatibility 2G
GSM network) supports making calls, sending messages, GPRS
network.have money
3).make sure the SIM card has opened the call shows and turned off the call
transfer.
4).Please insert the SIM card correctly. Cancel the PIN code
5).Do not assembly and disassembly device at will.
4
Choose a SIM card
Quick using
3.1 Put the SIM card into the as picture shows.
3.2 Product testing, need to be closed shell and screw ,then charge the battery
in time to keep it working normally.
3.3 take the device to outdoor and the front of device towards sky ,move device
to receive gps signal. Because indoor has no gps signal
3.4 Use mobile phone call the device and hang up or sending message
“smslink123456” to sim card in tracker ,tracker Will reply positioning
information
5
Picture (1) have gps signal Picture (2) no gps signal
Pic(1)：
Replied real-time tracking information under GPS satellites signal.
Lat:22.67533 lon:114.03913 Positioning of the latitude and longitude
values.
Spd：000.1 This refers to the device moving speed. The unit is km/h.
T:06/14/17 09:14 real-tracking time, the Default is London time. You can
set a time zone by sms command
Google Link: This is the link to the Google map showing the position of the
device.
Pic( 2) ：Replied last time position information. Now is LBS position
information. no gps signal
smcc:27a4 1223: Real-time LBS data.
Time:08/00/00 LBS positioning time.
If you receive positioning information is picture 2, please go out the outdoor
and Walk around with gps tracker,for receive The satellite signal
4.Command instruction
NOTE:
1)Device default password:123456)
2)use of mobile phones send messages to the tracker about all set command
6
3) The “+” in the command, please don’t type “+”, space means press
the space keyboard on your cell phone
4)After admin number setting, all alarm message will send authorization number
other cell-phone number send command will not reply
5) If you want standby time longer, pls don't open move alarm, and platform for
real-time location tracking.etc
4.1 Admin number setting:( support 5pcs admin number)
Command: admin123456+space+ phone number（This phone number is your
own mobile phone number , not the mobile number in tracker .）
Reply：admin ok
E.g：admin123456 13725556021
Note: support 5pcs admin number , Set the first authorization number,then use use
the first authorization number to set other authorization number,
If the authorization number forget or lost, you can send reset123456 to Restore the
factory Settings
Admin number Canceling:
Command ：noadmin123456 13725556021
Reply：noadmin ok
4.2 move Alarm setting (It works only in getting gps signal, the scope is a
circle that radius 200meters)
Command：move123456
Reply：move ok
7
E.g：
move alarm Canceling:
Command：nomove123456
Reply：nomove ok
4.3 Low battery alarm
When GPS device battery is Less than 30%, it will send SMS:low
battery+Ge-info alarm, at 3 minutes interval.
Canceling low battery alarm: send“low battery” to the tracker.
4.4. SOS help setting
Long Press the SOS button for 3 seconds, the tracker will send SMS “SOS
HELP!+lat./long.” to all the authorized numbers
E.g:
Canceling sos setting ：Command:“ help me“
E.g:
8
4.5 Monitor setting(option, The default do not have this function)
The default mode is “tracker” (Tracker mode).
Send SMS “monitor+password” to the unit,switch to “monitor” mode.then use
your mobile call the device sim card, Can listen to the voices around device
E.g:
Monitor Canceling Send SMS “tracker123456” to the unit, switch to “tracker” mode
4.6. Set Vibration alarm(option, The default not have this function)
Command ：“shock+password” to the device,it will start effective
After 5mins of static ,when the sensor is triggered ,and will send send Vibrate
alarm+latitude&longitude”
canceling Vibration alarm:
Command: “noshock+password”
Reply:noshock ok
9
4.7 Terminal (local) Time Setting (factory setting GMT 0)
Command：time+space+zone123456+space+ local time zone
Reply：time ok!
E.g：
NOTE:( 1 is east 1, - 1 is west 1, 30 is half the time zone)
4.8 Reset device
Command：reset123456
Reply：reset ok
4.9 Change the password
Command: password123456 888888
Reply :password OK
Note: 123456 is the old password(default ),888888 is the new password,it
must the 6 digits Arabic numerals
5.0 State Checking
Send SMS:”check+password” to the tracker device, it will reply the recent
status via SMS as: GSM: 100% GPS: OK/NO GPRS: ON/OFF battery: 100%.
Remark: GPS NO, only mean there are no GPS position request.
5.1 change IMEI number
Command: imei123456+space +new imei number
E.G: setimei123456 352887076633221
10
5.2 Add GPX history route record
First you have to insert TF card in the device
Send SMS: “ gpx+password” to tracker,it will reply : “ gpx ok” ,
then send SMS: “t001m***n+password” ,it will reply : “ tn ok”
Cancel gpx function ; send SMS : notn+password” it will reply: notn ok”
then send SMS: nogpx+password ,it will reply nogpx ok. Then auto enter
SMS mode.
Check the gpx data in google earth map :
Take out the TF card from device and connect with computer, copy the GPX file
to computer,then open the google earth map,then use goolge earth map open
the gpx file,you will see the route in the map.(you can download google earth
map app in the network )
NOTE: after set succeed GPX function,call device will not reply the google
link ,and stop send data to server.
6 .If you need real-time tracking by APP or website ,pls Operating as
follows
NOTE:If you need platform position, please use phone send “ gprs123456” to
device
6.1:Support Android & IOS APP tracking
If you need real-time tracking by APP ,please scan APP on web platform
OR Download “dagps”
1).scan QR code---open with browser--- choose Android or
Iphone---Download-- installation app
Otros manuales para GPS102B
2
Tabla de contenidos
Otros manuales de GPS de Coban
Coban
Coban GPS102B Manual de usuario
Coban
Coban gps104 TK104 Manual de usuario
Coban
Coban GPS107 Manual de usuario
Coban
Coban GPS105 Manual de usuario
Coban
Coban GPS-303 Manual de usuario
Coban
Coban TK06B Manual de usuario
Coban
Coban GPS304 Manual de usuario
Coban
Coban GPS106A Manual de usuario
Coban
Coban VT105 Manual de usuario
Coban
Coban K103B Manual de usuario
