CNC4PC C34HS2 Manual de usuario

USER’S

MANUAL

VER. 1

C34HS2 BOARD

Rev. 1

OCTOBER, 2020

User’s Manual Page i

USER'S MANUAL

TABLE OF CONTENTS

Contents Page #

1.0 OVERVIEW.....................................................................................................................1

2.0 FEATURES.....................................................................................................................1

3.0 BOARD DESCRIPTION..................................................................................................1

4.0 JUMPER TO SELECT THE ENABLE.............................................................................2

5.0 ALARM TERMINAL........................................................................................................4

6.0 WIRING SAMPLE...........................................................................................................4

7.0 PINOUT...........................................................................................................................5

8.0 DIMENSIONS..................................................................................................................6

User’s Manual Page 1

1.0 OVERVIEW

This board interface is used for the connection between C82, C76, M16D and Closed

Loop Steppers DRIVE.

2.0 FEATURES

•RJ45 Driver Input Connector

•Select Jumper for Hard Enable or Soft Enable.

•Alarm terminal

•Select jumper for signal differentials.

•Select Jumper active Low and active High

•Adjustable resistor to allow adjusting the fault sensibility

3.0 BOARD DESCRIPTION

User’s Manual Page 2

4.0 JUMPER TO SELECT THE ENABLE

Use Software Enable to keep the driver active only while the system is active.

Set of jumpers as shown in the image.

SOFT ENABLE

Use Hardware Enable to keep the driver enabled all the time.

Set of jumpers as shown in the image.

HARD ENABLE

JUMPER TO SELECT THE DIFFERENTIAL

If working the inputs of STEP and DIR as differentials signals, you have to use the board, set

jumper as shown in the image.

DIFERENTIAL

User’s Manual Page 3

If not use the differential signal for STEP & DIR, set jumper as show in the image.

STEP & DIR

JUMPER TO SELECT ACTIVE LOW AND ACTIVE HIGH

1-2: ACTIVE LOW

2-3: ACTIVE HIGH

User’s Manual Page 4

5.0 ALARM TERMINAL

6.0 WIRING SAMPLE

User’s Manual Page 5

7.0 PINOUT

C34HS CONNECTOR RJ45

RJ45 Pins

Function

NOT USED

PUL+

NOT USED

GND

ERR

DIR+

NOT USED

8 (5V)

EN+

User’s Manual Page 6

8.0 DIMENSIONS

All dimensions are in Millimeters.

DISCLAIMER

Use caution. CNC machines can be dangerous machines. Neither DUNCAN USA, LLC

nor Arturo Duncan are liable for any accidents resulting from the improper use of these

devices. This product is not a fail-safe device and it should not be used in life support

systems or in other devices where its failure or possible erratic operation could cause

property damage, bodily injury or loss of life.

Tabla de contenidos

Otros manuales de Hardware de computadora de CNC4PC

CNC4PC

CNC4PC C34AB Manual de usuario

CNC4PC

CNC4PC C25XP Manual de usuario

CNC4PC

CNC4PC C25 Manual de usuario

CNC4PC

CNC4PC C1G Manual de usuario

CNC4PC

CNC4PC C34SGDM-BOARD Manual de usuario

CNC4PC

CNC4PC C36S Manual de usuario

CNC4PC

CNC4PC C15 Manual de usuario

CNC4PC

CNC4PC C52- ESS Manual de usuario

CNC4PC

CNC4PC C34DE Manual de usuario

CNC4PC

CNC4PC M26- 12R Manual de usuario

CNC4PC

CNC4PC C86ACCP Manual de usuario

CNC4PC

CNC4PC C34DE-B Manual de usuario

CNC4PC

CNC4PC M26- 12R Manual de usuario

CNC4PC

CNC4PC C34TSM Manual de usuario

CNC4PC

CNC4PC C34G320X Manual de usuario

CNC4PC

CNC4PC C86ACCP6 Manual de usuario

CNC4PC

CNC4PC C80 Manual de usuario

CNC4PC

CNC4PC C34ELP Manual de usuario

CNC4PC

CNC4PC C3 Manual de usuario

CNC4PC

CNC4PC C34KY-M Manual de usuario

CNC4PC

CNC4PC C11 Manual de usuario

CNC4PC

CNC4PC M28 Manual de usuario

CNC4PC

CNC4PC C34YAKO Manual de usuario

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario