Cod.006.0001.1841
01/09/2014 v2.0
ENGLISH
0
3/34
1INTRODUCTION .....................................................................4
2FRONT PANEL .......................................................................4
3REAR PANEL .........................................................................5
4INSTALLATION ......................................................................5
4.1 CONNECTIONS TO THE ELECTRICAL MAINS NETWORK.5
4.2 PREPARING FOR MMA WELDING........................................5
4.3 PREPARING FOR TIG WELDING ..........................................6
5USER INTERFACE .................................................................8
6UNIT POWER-UP....................................................................9
7RESET (LOAD FACTORY SETTINGS)..................................9
7.1 PARTIAL RESET.....................................................................9
7.2 TOTAL RESET ......................................................................10
8SET-UP (INITIAL SET-UP OF THE WELDING POWER
SOURCE) ..............................................................................10
8.1 TORCH LOADING.................................................................12
9ALARMS MANAGEMENT ....................................................12
THERMAL ALARM! ..........................................................................12
COOLING DEVICE ALARM..............................................................12
10 WELDING PARAMETERS....................................................13
Welding current.................................................................................13
Max welding current..........................................................................13
Hot-start ............................................................................................13
Arc-force............................................................................................13
VRD...................................................................................................13
Long arc voltage ...............................................................................13
Remote control..................................................................................13
Dynamic arc ......................................................................................13
Second current Bi-level.....................................................................13
Base current......................................................................................13
Peak time..........................................................................................14
Base time..........................................................................................14
Pulse frequency ................................................................................14
Slope down .......................................................................................14
Final current......................................................................................14
Post-gas............................................................................................14
Pre-gas..............................................................................................14
Start current ......................................................................................14
Slope up............................................................................................14
Spot TIG time....................................................................................14
HF arc start .......................................................................................14
Minimum pedal current .....................................................................14
Q-start ...............................................................................................14
Multi-tack...........................................................................................14
AC wave in mix AC-DC.....................................................................14
Extra fusion.......................................................................................14
AC frequency ....................................................................................15
AC balance .......................................................................................15
Electrode diameter............................................................................15
10.1 PARAMETERS ACTIVATION ...............................................16
11 WELDING SETTINGS...........................................................18
11.1 ELECTRODE WELDING (MMA) ...........................................18
11.1.1 MMA PARAMETERS SETTING (1ST LEVEL).................................18
11.1.2 MMA PARAMETERS SETTING (2ND LEVEL) ................................18
11.1.3 MMA SPECIAL FUNCTIONS ...........................................................18
11.2 DC TIG WELDING.................................................................19
11.2.1 DC TIG PARAMETERS SETTING (1ST LEVEL).............................19
11.2.2 DC TIG PARAMETERS SETTING (2ND LEVEL) ............................19
11.2.3 DC TIG SPECIAL FUNCTIONS MENU............................................20
11.3 AC TIG WELDING.................................................................21
11.3.1 AC TIG PARAMETERS SETTING (1ST LEVEL) .............................21
11.3.2 AC TIG PARAMETERS SETTING (2ND LEVEL).............................21
11.3.3 AC TIG SPECIAL FUNCTIONS MENU............................................22
12 JOBS MANAGEMENT..........................................................23
12.1 SAVING A JOB......................................................................23
12.2 LOADING A USER JOB OF FACTORY SET JOB................23
12.3 DELETING A JOB .................................................................23
13 TORCH TRIGGER MODES ..................................................24
13.1 2T LIFT-ARC WELDING........................................................24
13.2 2T HF WELDING...................................................................24
13.3 4T LIFT-ARC WELDING .......................................................24
13.4 4T HF WELDING...................................................................25
13.5 BI-LEVEL LIFT WELDING ....................................................25
13.6 BI-LEVEL HF WELDING.......................................................25
13.7 2T SPOT WELDING..............................................................25
13.8 2T SPOT HF WELDING........................................................26
13.9 PILOT ARC WELDING..........................................................26
14 TECHNICAL DATA...............................................................27
15 SPARE PARTS.....................................................................28
16 ELECTRICAL DIAGRAM .....................................................30
16.1 GLW 302 ...........FEHLER! TEXTMARKE NICHT DEFINIERT.
16.2 TORCH CONNECTOR .........................................................32
16.3 REMOTE CONTROLLER CONNECTOR .............................32
