Clifford ACE 2000 Manual de usuario

AutoFax & Technical Support Helpline:

1-800-444-4667

For the latest vehicle wiring information and for

wiring diagrams and servicing information on

older Clifford products:

24-hour AutoFax: 1-800-444-4667

24-hour dealer website: www.clifforddealer.com

Clifford Electronics, Inc. n 20750 Lassen Street n Chatsworth, CA 91311

1-800-824-3208 or 1-818-709-7551

n fax 1-818-407-1743

Table of Contents

Important Information................................2

Required Installation Tools.................................2

Standard Features of the ACE 2000.........................3

System Components.................................3

Wiring Diagram ...................................4

Wiring Descriptions.................................5

Passenger Compartment Connections........................5

Control Unit and Antenna..................................5

Door Trigger/Interior Light Supply..............................5

Central Door Locking System................................5

Door Locks.........................................6

LED Status Indicator.....................................8

PlainView 2 Coded Valet Switch...............................8

Dual-Zone Piezo Sensor...................................8

Trunk Trigger........................................8

Parking Lights........................................8

Auxiliary A with Selectable Output Type and AutoActivation.................10

Starter or Ignition Immobilization Circuit..........................10

High Output Siren.....................................10

Hood Trigger.......................................11

Final Wiring Connections..............................11

SmartPowerUp 2 ..................................11

Delayed Courtesy Lights..............................11

Remote Control Operation.............................11

FACT.........................................12

Eight-Event TotalRecall...............................12

Programmable Features..............................13

Using the CliffNet Wizard Pro Installation Software.....................13

Programming the User-Selectable Features.........................13

User-Programmable Features...............................14

Installer Programmable Features..............................16

System Checklist and Troubleshooting.......................16

Important Information

1.DO NOT disconnect the battery cables! Make battery connections by removing the lug

nuts from the battery clamps without detaching the clamp itself.

2.Turn off the interior lights or remove the dome light fuse before starting the installation ;

otherwise, leaving the door(s) open during installation will drain the battery.

3.Use a voltmeter. DO NOT USE A TEST LIGHT! Test lights have a current drain that

will damage the vehicle’s onboard computer, and if you probe the wrong wire, could

deploy the vehicle’s air bag(s).

4.Make all connections with the supplied crimp connectors or solder and shrink tube. DO

NOT use bite-type connectors.

5.Route the system’s ground and power wires directly to the vehicle battery or fuse box.

6.Keep extension as short as possible. Use same-gauge wire for short extensions, larger

gauge for longer extensions. DO NOT USE SPEAKER WIRE!

7.Discuss placement of the LED, valet switch, window decals, etc. with the vehicle owner

prior to installation.

8.DO NOT mount components nor route wires near hot or moving vehicle parts. Clifford

components must not impede vehicle servicing or operation.

9.DO NOT mount any Clifford sensor in the engine compartment (with the exception of

the OmniSensor sensing module).

10.Follow the system’s Sequence of Installation to ensure proper installation and testing.

11.Place the owner’s manual in the glove box.

Note: Clifford Electronics’ web site for Authorized Clifford Dealers has

detailed descriptions of wire colors and locations for most foreign and

domestic vehicles. Installation diagrams and programming procedures for

older Clifford products are also available. Just go to

www.clifforddealers.com for assistance 24-hours per day.

Required Installation Tools

Voltmeter (set to “DC Volt”)

Wire crimper

Wire stripper

Electric drill and bits

Phillips screwdriver

Crescent wrench

Vinyl tubing

Rubber grommet

Convoluted tubing

Shrink tubing (included)

Solder gun and solder

Heat gun

Standard Features of the ACE 2000

*Programmable (+) or (-), may require relays.

System Components

The ACE 2000 installation kit contains the following components:

One Prewired 20-pin connector harnessOne PlainView 2 Coded Valet Switch

One Prewired 2-pin connectorOne High Output Siren

One ACE 2000 Control UnitOne Prewired LED

One Hardware KitOne User’s Manual

One Dual-Zone Piezo Sensor Two Clifford Window Decals

Two Remote Transmitters18” Cliffnet DataPort Extension Cable

One Antenna 3

oLifetime Warranty

oTwoACG™ 2 (Anti-CodeGrabbing™)

Remote Controls

oAudible Low Transmitter Battery

Warning

oBuilt-In Starter or Ignition Immobilizer

oFACT — False Alarm Control and Test

oRemote Siren Silencing

oDual-Zone Piezo Sensor™

oDual-Mode “Chirp” Silencing

oPatented UltraSecure Coded Valet

Mode™

oDataPort™ for CliffNet Wizard Pro

oPoint-and-Click Feature Programming

oComplete Online System Diagnostics

At-A-Glance

oHigh-Output Siren

oRemote Door Locking/Unlocking*

oRemote Panic with Smart

Locking/Unlocking*

oBuilt-In Dual Parking Light Flasher

with Onboard Relay

oRemote Controlled Courtesy Lighting

Output

oPatented Smart AutoTesting™

oSmart Remote Trunk Release

oUser-Selectable AutoArming

oAutoArm & Lock

oVisual AutoArm Indication

oInstant AutoArm Bypass

oPatented Malfunction AutoBypass™

with AutoReMonitoring

oPatented SmartPowerUp™ 2

oMultiple-Car Control

oEight-Event TotalRecall™

oPatented Smart Prior Intrusion Attempt

Alert

oPatented Remote Control Code

Learning and MultiRemote

Recognition

oClear All Remotes

oHigh-Luminescence LED Status Parking

with Automatic Battery-Saving Mode

oFull-Time SecureAccess™

Programming

oAdvanced CMOS Microcomputer

oPre-Loomed Wiring

oAccessory Output with Selectable

Output Type

oInstaller-Selectable Door

Ajar/Delayed Courtesy Lights

oPrewired LED, Sensor and PlainView 2

Switch Connectors

Wiring Description for the 2-pin Connector

PinWire ColorConnects to

1White/RedStarter or Ignition Interrupt - key side

2White/Red Starter or Ignition Interrupt - starter or ignition side

Wiring Description for the 20-pin Connector

PinWire ColorConnects to

1GrayDoor trigger input (+) or (-)

2WhiteValet Switch input (-)

3OrangeSensor input trigger zone (-)

4Gray/Yellowtrunk and hood trigger input (-)

5Blue Sensor input warning zone (-)

6Violet LED output (+)

7White/BrownIgnition Input

8BlackGround for the Dual-Zone Piezo Sensor, optional sensor and LED

connectors, Valet Switch

9Black Battery Negative

10 RedPower for the Dual-Zone Piezo Sensor, optional sensor

11 Brown/WhiteInterior light output (-)

12 Gray/GreenDoor lock output (+) or (-)

13 Gray/Orange Door unlock output (+) or (-)

14 GreenArmed output (-)

15Gray/VioletAuxilliary A output (-)

16 YellowSiren output (-)

17Brown Parking light output (+)

18 BrownParking light output (+)

19 Red/WhiteBattery positive with 20 Amp fuse

20 RedBattery positive with 5 Amp fuse

Passenger Compartment Connections

Control Unit and Antenna

The ACE 2000 control unit must be installed inside the vehicle. Under no

circumstances should the unit be installed under the hood or other similarly

hostile environment.

1.Select an area behind the dash to mount the control unit using wire ties, but do not

permanently affix it until all wiring and testing is complete.

2.Plug the 18” CliffNet DataPort Extension Cable into the control unit. Make sure the

receptacle end will be easily accessible after the dash has been secured back to its original

position. This extension cable ensures ease of service later on.

3.Run the antenna either up the window pillar or under the dash, away from metal. Do not

fold the excess cable or antenna wire. Do not make hard, sharp bends.

Door Trigger/Interior Light Supply

Door triggers on most autos are negative (except most Rolls-Royce and Ford autos). To

determine door trigger polarity, use the following procedure:

1.Find the wire coming off the rear of the vehicle door switch.

2. Connect the negative voltmeter lead to ground.

3.Find the one wire that shows +12 volts when the switch is pressed in and 0 volts when

released. This is a negative trigger door wire.

4.If you don’t get the indications noted in step 3, find the one wire that shows 0 volts when

the switch is pressed in and +12 volts when released. This is a positive trigger door wire.

5.Connect the system’s thin GRAY wire to the door wire.

6.If the door trigger is negative, no further installation is required.

Door Trigger/Interior Light Supply (Continued)

7.If the door trigger is positive, program for positive using the Installer-Programmable

features matrix on page 14.

8.If dome light supervision is desired, connect the relay as shown in the ACE 2000 diagram.

nConnect the BROWN/WHITE wire to terminal 86

nTap a wire in to the RED/WHITE wire (+12V) and connect it to terminal 85.

nTap a wire into the GRAY wire and connect to terminal 30.

nConnect terminal 87 to positive if the door trigger is positive (+12V RED/WHITE

wire), or connect terminal 87 to negative if the door trigger is negative.

NOTE: Clifford Electronics’ web site for Authorized Clifford Dealers has

detailed descriptions of wire colours and locations for most foreign and

domestic vehicles. Installation diagrams and programming procedures for

older Clifford products are also available. Just go to

www.clifforddealers.com for assistance 24-hours per day.

Central Door Locking System

Please refer to the Door Lockssection below for information on circuit types and connections.

When adding an IntelliStart 4 to the ACE 2000, it is recommended that RPM-dependent

door locking be selected. The RPM-dependent door locking feature is only available with the

addition of the IntelliStart 4.

Door Locks

WARNING: If the power door locks do not operate properly when the system

is armed and disarmed, DO NOT USE THE VEHICLE’S DOOR LOCK SWITCH! If

the control unit’s door lock wires are miswired, permanent damage to the

controlunitortothecar’selectricalsystemand door lock servos willresult. If

you require assistance, call the Clifford Technical Support Helpline PRIOR to

wiring the door locks.

If the vehicle is not equipped with power door locks, you may optionally add up to four

#60-516 DoorLock Servos. Some systems may require adding relays.

Determining the Door Lock System Type

1.Remove the door lock switch on the driver’s side of the vehicle to reveal the switch wires.

a.If there are four or more wires, make the connections shown in Diagram 4 for reverse

polarity.

b.If there are three wires, proceed to step 2.

c. If the vehicle is a Nissan and it does not have a door lock switch, find the single wire in

the driver’s kick panel that shows ground when the locks are unlocked and “open”

when the locks are locked. Cut this wire and make the connections shown in Door

Lock/Unlock Diagram 3.

2.Connect the negative voltmeter lead to ground and probe each wire while

locking/unlocking. If the voltmeter show +12v while activating the switch, make the

connections shown in Door Lock/Unlock Diagram 1 for positive trigger. Otherwise, go to

step 3.

a. On systems without lock/unlock relays (Arrow 3, etc.) you must program for positive

door locks (factory setting is negative)when the system has been powered up.

3.Repeat step 2 with the negative voltmeter lead connected to +12v. If the voltmeter

shows +12v while activating the switch, make the connections shown in Door

Lock/Unlock Diagram 2 for negative trigger.

4.Locks controlled from the driver’s door key require installation of just one #60-516 servo

in the driver’s door. Vehicles without factory power locks require a servo in each door.

Mount the servo(s) and make the connections shown in Door Lock/Unlock Diagram 5 for

adding servos.

Door Locks (Continued)

5.On a vacuum-pump-type Mercedes Benz or Audi, make the connections shown in Door

Lock/Unlock Diagram 6, then (if 1989 or older) program the system for a 3-second lock

pulse.

Passenger Compartment Connections (Continued)

LED Status Indicator

Select a prominent location on the dash or console visible through all windows. Discuss

placement with the owner.

1. Verify there is adequate space to accommodate the LED, then drill a 5/16” (8mm) hole

and route the wires through it.

2.Mate the LED connectors to the VIOLET and BLACK wire connectors as shown in the

diagram on page 4.

3. Press the LED into place.

PlainView 2 Coded Valet Switch

1.Discuss placement of the switch with the vehicle owner and avoid placing the switch

where it can be pressed accidentally. It should be placed in a location that is easily

accessible to the driver.

2.Verify there is adequate space behind the selected location to accommodate the switch.

3.Drill a 5/16” (8mm) mounting hole, then insert the wires through the hole and mount the

switch.

4.Mate the switch’s locking connectors to the WHITE and BLACK locking connector.

5.Remove the adhesive backing and press into place.

Dual-Zone Piezo Sensor

Mount the Dual-Zone Piezo Sensor in the passenger compartment, not in the engine

compartment.

1.Firmly mount the sensor near the base of the steering column (if the steering column has a

rotating sleeve, firmly screw the sensor to the interior firewall, kick panel or trunk wall).

Make certain that the adjustment screw is accessible.

2.Mate the sensor to the connector on the wireloom with the BLACK, RED, BLUE and

ORANGE wires.

Trunk Trigger

Vehicles with negative switching trunk light will interface directly with the ACE 2000 (on positive

switching vehicles, use a relay to invert polarity). The switch may be located in or near the trunk

latch or at the trunk light. If a switch cannot be located, you must add a pin switch in a locatio n

away from water channels.

Note: If the vehicle has a dashboard trunk ajar indicator, install a 1A diode between the light

and switch with the diode band pointing toward the switch.

1.Connect the GRAY/YELLOW wire to the trunk switch (between the diode and switch if

you added a diode)..

Parking Lights

To determine whether the vehicle has single or dual parking light circuit(s), you must access

the fuse panel. A single circuit has one fuse; a dual circuit has two.

Single Parking Light Circuit (Most Japanese and American Vehicles)

1.Turn on the parking lights and access the Parking Light wiring in one of the following

locations:

nNear the headlight switch

nIn the door sill harness going to the rear lights

nAt any of the four Parking Light bulbs

2.If working underdash, be sure to turn the dashlight dimmer to its lowest setting.

Otros manuales para ACE 2000

Tabla de contenidos

Otros manuales de Alarma de coche de Clifford

Clifford

Clifford Concept 450 Manual de usuario

Clifford

Clifford Polaris II Manual de usuario

Clifford

Clifford intelliguard 700-IQ Manual de usuario

Clifford

Clifford Concept 60 Manual de usuario

Clifford

Clifford Smart Remote Starter Manual de usuario

Clifford

Clifford Wireless Immobilizer XL 500 Manual de usuario

Clifford

Clifford Arrow 5.1 Manual de usuario

Clifford

Clifford Nova 200LE Manual de usuario

Clifford

Clifford CYBER 2 Manual de usuario

Clifford

Clifford 470.4X Manual de usuario

Clifford

Clifford Sabre Manual de usuario

Clifford

Clifford 4115X Manual de usuario

Clifford

Clifford Matrix 1 Manual de usuario

Clifford

Clifford Tazor II Manual de usuario

Clifford

Clifford SmartWindows 4 Manual de usuario

Clifford

Clifford 3105X Manual de usuario

Clifford

Clifford Responder LE 5806X Manual de usuario

Clifford

Clifford SE 2020 Special Edition Manual de usuario

Clifford

Clifford SmartWindows Manual de usuario

Clifford

Clifford 300UK Instrucciones de funcionamiento

Clifford

Clifford AvantGuard 2 Manual de usuario

Clifford

Clifford 10.5X Manual de usuario

Clifford

Clifford AVANTGUARD 5 Manual de usuario

Clifford

Clifford intelliguard 800-IQ Manual de usuario

Manuales populares de Alarma de coche de otras marcas

Ultra Start

Ultra Start 2500M SERIES Manual de usuario

Ultra Start

Ultra Start 650 Series Manual de usuario

Audiovox

Audiovox Prestige Platinum+ APS-511C Manual de usuario

Sparkrite

Sparkrite SRA8 Manual de usuario

Viper

Viper 4708V Manual de usuario

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Manual

Falcon

Falcon Predator XL3 Guía del usuario

Audiovox

Audiovox Auto Security XR91 Instrucciones de funcionamiento

CrimeStopper

CrimeStopper CS-8717 Guía de inicio rápido

Ultra Start

Ultra Start 450 SERIES Manual de usuario

Scytek electronic

Scytek electronic Vectra X3 Manual de usuario

Excalibur

Excalibur AL-1860-EDPB Manual de usuario

Gemini

Gemini 7057 Manual de usuario

FlashLogic

FlashLogic FLRSBA PRESTIGE Manual de usuario

Magicar

Magicar FAI-440 Manual de usuario

Viper

Viper 560XV Manual de usuario

SECO-LARM

SECO-LARM 300C Manual de usuario

Python

Python 660XP Manual de usuario