Clenergy SPH15 Manual de usuario

Page 1of 26

Clenergy SPH Installation and Operation Manual

SPH Grid PV-inverter

Installation and Operation Manual

SPH MODELS

INCLUDED IN THIS MANUAL

SPH15 1500W

SPH20 2000W

SPH30 3000W

SPH40 4000W

SPH60 6000W

N305 WeiYe Building, Pioneer Park XiaMen China 361006

Tel: +86-592-5781288

Fax: +86-592-5782298

Website: www.clenergy.com.cn

Page 2of 26

Clenergy SPH Installation and Operation Manual

Important Safety Information

Warning - Risk of Electric Shock

Failure to comply with these warnings and instructions can result in

damage to property, risk of fire, serious injury or death.

Do not remove the covers. The unit contains no user serviceable parts.

Hazardous voltage is present inside the unit from both DC and AC sources.

Hazardous voltage remains inside the unit even when disconnected.

The photovoltaic (PV) array supplies hazardous voltage when exposed to

light, even at very low intensity. Even ungrounded photovoltaic arrays

present an electric shock hazard through ground capacitance.

The unit is designed to supply power to the electric grid (AC utility) only. It

must not be connected to other AC electric generators or power supplies.

This may cause permanent damage to the unit and/or AC power supply.

The earth connection of the electric grid (AC utility) to the inverter should be

firm and visible.

Connection to the electric grid (AC utility) typically requires a permit or

interconnection agreement with the electricity provider. Contact your

electricity provider for more information.

All local and national codes and regulations for installation, wiring and

inspection of electrical equipment must be complied with.

Installation and troubleshooting of this unit must only be performed by

properly trained electricians or installation technicians, qualified to install or

service PV inverters.

Incorrect installation, troubleshooting by unqualified persons or modification

of the electrical wiring poses a safety risk to the installers, home/facility

occupiers and other users/operators of the electric grid (AC utility).

Page 3of 26

Clenergy SPH Installation and Operation Manual

Both AC and DC voltage sources are terminated inside this equipment. The

unit must not be opened until both AC and DC circuits have been individually

disconnected for at least 3 hours. (Due to risk of electric shock from energy

stored in capacitors.)

Please take out the unit from the packaging box carefully. Check if there is

any obvious damage. Do not install the unit, if it is damaged. Please contact

your local dealer for a replacement.

The SPH inverter is the latest transformer less design. Please check the

requirements for your country regarding earthing regulations.

Page 4of 26

Clenergy SPH Installation and Operation Manual

Before you start…

Thank you for purchasing the SPH Grid PV-Inverter. This is a highly reliable

product due to innovative design and precise quality control. When installed and

operated correctly, it will give many years of trouble free operation.

This manual contains important information for the safe and effective

installation and operation of the SPH Grid PV-Inverter. Be sure to read this

manual carefully before using the product.

If you encounter any problem during the installation or operation of the unit,

please check this manual first before contacting your local dealer or

representative. Most of the problems you may encounter can be solved by

following the instructions inside the manual.

Please keep this manual in a safe place for later use.

Page 5of 26

Clenergy SPH Installation and Operation Manual

1. SPH inverter overview and connections

1.1. SPH15, SPH20 & SPH30

Front view Bottom view

External protective earth (PE)-terminal

Display and connections

LCD Display: Showing the

inverter status

RS232

Solar panel input

(DC)

Display information switch

Optional communication

slot: SNMP and RS485

USB

AC connector

Operation LED,

Blue, Working Mode

Operation LED, Red,

fault status

Page 6of 26

Clenergy SPH Installation and Operation Manual

1.2. SPH40

Front view Bottom view

Display and connections

External protective earth (PE)-terminal

LCD Display: Showing the

inverter status

Display information switch

Operation LED,

Blue, Working Mode

Operation LED, Red,

fault status

AC connector

Optional communication

slot: SNMP and RS485

USB

RS232

Solar panel input

(DC)

Page 7of 26

Clenergy SPH Installation and Operation Manual

1.3. SPH60

Front view Bottom view

Display and connections

External protective earth (PE)-terminal

Display information switch

LCD Display: Showing the

inverter status

Operation LED,

Blue, Working Mode

Operation LED, Red,

fault status

AC connector

Optional communication

slot: SNMP and RS485

USB

RS232

Solar panel input

(DC)

Page 8of 26

Clenergy SPH Installation and Operation Manual

2. PV installation system diagram

PV array: Provides DC power to the SPH inverter. A DC

Disconnect Switch or optional Solar Concentrator is usually

fitted between the PV array and the SPH inverter.

SPH inverter: Converts DC power from the PV array into AC power. The AC

(Alternating Current) power is supplied to the electric grid (AC

utility). The SPH inverter uses Maximum Peak Power Tracking

(MPPT) to optimize the PV array operation and deliver

maximum power to the electric grid.

Connection: The “interface” between the SPH inverter and the

System Grid usually consists of an electrical breaker or fuse and

terminals for connection. It may also contain a disconnect

switch. For proper safety, this part must be designed by a

qualified electrician or electrical installation technician.

Utility: The electricity supply from the main electric grid

system must be single phase 220V to 250V, 50Hz

or 60Hz.

Connection System

SPH Inverter

Utility

PV Array

Disconnect

Switch

Page 9of 26

Clenergy SPH Installation and Operation Manual

3. Installation

Before starting installation please check the following items:

This unit is suitable for indoor and outdoor usage. For best performance and

service life, outdoor installations should be sheltered from direct exposure to

rain and water.

The unit can operate with an ambient temperature of -25C to +55C. For

best performance and service life, the unit should be operated with an

ambient temperature of 0C to +40C. Above this temperature, the power

output may be reduced. It is recommended to shade the unit from direct

exposure to sunlight to prevent increased operating temperature.

The electric grid must be 220V to 250V, 50Hz or 60Hz single-phase.

Connection to electric grid must be approved by the electricity provider.

The installation must be done by a certified electrician.

The unit must be installed vertically in the orientation shown.

25cm Space

Page 10 of 26

Clenergy SPH Installation and Operation Manual

Step1: Mount SPH inverter to the wall or other vertical

surface

1. Select a solid wall or vertical surface to mount the unit. The mounting

surface must have sufficient strength to carry the weight of the unit (Given

in the specification). In areas of seismic activity, additional support or

restraint may be necessary. It is recommended that the inverter is installed

at a height that provides comfortable viewing and operation of the display

and controls.

2. There must be at least 25cm clear space above and below the unit. This is

to allow for proper air circulation and convection cooling.

3. Mark the 4 mounting hole positions required using the mounting backplate

as a template.

SPH15

SPH20

SPH30

SPH40

SPH60

W (mm)

312

465

H (mm)

362

386

516

D (mm)

131

141

131

142

4. Select appropriate mounting hardware for the type of mounting surface and

drill mounting holes of the appropriate size.

5. Fix the mounting backplate to the mounting surface using the selected

hardware at each of the 4 mounting holes.

6. Fix four screws with spacer on the four corners of the mounting back plate.

7. Hang the inverter unit onto the mounting back plate and press down.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Inversor de Clenergy

Clenergy

Clenergy PV-ezRack Manual de usuario

Clenergy

Clenergy PV-ezRack SolarTerrace II-F Manual de usuario

Clenergy

Clenergy PV-ezRack SolarRoof Manual técnico

Clenergy

Clenergy PV-ezRack SolarTerrace Eco Manual de usuario

Clenergy

Clenergy PV-ezRack Manual de usuario

Clenergy

Clenergy PV-ezRack SolarRoof Isolator Shade Manual de usuario

Clenergy

Clenergy PV-ezRack Ascent Manual de usuario

Clenergy

Clenergy PV-ezRack SolarRoof Manual de usuario

Clenergy

Clenergy PV-ezRack Grounding system Manual técnico

Clenergy

Clenergy PV-ezRack SolarFloating I Manual de usuario

Clenergy

Clenergy PV-ezRack SolarTerrace II Manual técnico

Clenergy

Clenergy PV-ezRack PostMount 4-A Manual de usuario

Clenergy

Clenergy PV-ezRack SolarRoof Manual de usuario

Clenergy

Clenergy PV-ezRack SolarRoof Manual técnico

Clenergy

Clenergy PostMount 6-A Manual de usuario

Clenergy

Clenergy PV-ezRack SolarRoof Manual técnico

Clenergy

Clenergy SPH50 Manual de usuario

Clenergy

Clenergy PV-ezRack SolarRoof ER-TL-10/15 Manual de usuario

Clenergy

Clenergy PV-ezRack Commercial Tilt Manual de usuario

Manuales populares de Inversor de otras marcas

Fourgroup

Fourgroup Easy Manual de usuario

Velleman

Velleman PI300M Manual de usuario

Sungrow

Sungrow SG350HX-US Manual de usuario

WilTec

WilTec 61897 Manual de usuario

SMA

SMA SUNNY BOY STORAGE 2.5 Manual de usuario

Simplicity

Simplicity LANDLORD 316 Manual de usuario

Santak

Santak SMAX 3000 Manual de usuario

ATON

ATON RA.Store-3 Manual de usuario

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ Manual de usuario

Tektronix

Tektronix CFG250 Manual de usuario

Champion

Champion 200989 Manual de usuario

Vanner

Vanner 20-500 Series Manual de usuario

GE GEP Manual de usuario

Astrel Group

Astrel Group Power Reducer Guía rápida

MULTIQUIP

MULTIQUIP GDP-5H Guía

GoWISE

GoWISE PS1007 Manual de usuario

Promate

Promate PM13500D ES Manual de usuario

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM Manual de usuario