Clek Q-Tether Manual de usuario
Foonf + Fllo
Q-Tether Manual
Failure to properly install or use this accessory or follow these
warnings and instructions, the instructions provided with your
car seat, and the information on the car seat’s labels can
result in serious injury or death of the child in a sharp turn,
sudden stop, or crash.
• Use only with Clek Foonf or Fllo convertible car seats.
• Only use Q-tether when installing Clek Foonf or Fllo
convertible car seats rear-facing. NEVER use Q-tether
when installing Foonf or Fllo forward-facing.
• Always adjust Q-Tether Connector Strap so that Splitter
Plate is located on top of vehicle seat back. NEVER use
Q-tether with Splitter Plate in front of vehicle seat back.
• Do not tighten Q-tether more than needed to remove slack.
Overtightening Q-tether could shift the position of the car
seat resulting in a seat too upright.
• Only connect Tether Hook to a designated tether
anchor. NEVER connect Tether Hook to an unapproved
anchor point.
• Only connect Tether Hook to the tether anchor dedicated
for the seating position being used. NEVER connect Tether
Hook to an adjacent tether anchor.
WARNING — DEATH or SERIOUS INJURY can occur
Checklist for Proper Use of Q-Tether
IMPORTANT: This is only a checklist – you must read and
understand all of the warnings and instructions provided with
your Clek car seat and in these instructions before installing or
using the Q-Tether.
Foonf or Fllo is installed rear-facing according to car seat
instruction manual.
Tether Hook is connected to designated tether anchor.
Q-Tether Connector Strap is tightened so that Splitter Plate is
located on top of vehicle seat back.
Loops at end of Q-Tether are properly attached to Splitter Plate
and completely inside the slot.
Q-Tether adjuster is located on side of vehicle where child will
be loaded and unloaded.
Q-Tether is correctly routed through both Forward-Facing Belt
Lock-offs and both Lock-offs are closed.
Q-Tether Strap must not pass between Shoulder Harness Straps
and back of seat.
Q-tether webbing is tightened to be snug without lifting or
shifting position of car seat.
Vehicle Information
Figure 2
• Tether anchors have been
provided in second row
seating positions by most
vehicle manufacturers
since 2001.
• Top tether anchors are found
behind the vehicle seat as
shown in Figure 1.
• If covered, the tether anchor
locations may be identified by
a symbol as shown in Figure 2.
• See your vehicle owner’s
manual to identify what seating
positions have a tether anchor.
• See your vehicle owner’s
manual for instructions on
routing and connecting the
Tether Hook relative to any
vehicle features such as a
vehicle headrest.
Figure 1
Q-Tether Features
1Tether Hook
2Q-Tether Connector Adjuster
3Q-Tether Connector Strap
4Splitter Plate
5Q-Tether Attachment Loops
6Q-Tether Adjuster
7Q-Tether Strap
4
6
7
1
3
2
5 5
IMPORTANT: Car seat MUST be properly installed according to
the instructions in the car seat manual in a vehicle seating position
with a designated tether anchor before installing Q-Tether.
Installing Q-Tether
Step 1
Locate tether anchor as shown
in Figure 3. If covered, the tether
anchor may be identified by a
symbol, as shown in Figure 2.
Step 3
Attach Tether Hook to
vehicle tether anchor as
shown in Figure 5 or 6.
Step 2
Loosen Q-Tether Connector
Strap by pressing and holding
Q-Tether Connector Adjuster
while pulling strap as shown in
Figure 4.
Figure 3
Figure 4
Figure 5 Figure 6
Step 4
Check that Q-Tether Adjuster
is connected to side of Splitter
Plate closest to where child will
be loaded and unloaded.
Option 1: If Q-Tether Adjuster
needs to be moved to other
side of Splitter Plate:
• Remove loop at each
end of Q-Tether Strap
from Splitter Plate
by sliding strap out
through slot in Splitter
Plate as shown in
Figure 7.
• Position Q-Tether
Strap so that Adjuster
is located on side of
Splitter Plate closest
to where child will be
loaded and unloaded.
Figure 7
Step 5
Press and hold Q-Tether
Adjuster and pull out on
Q-Tether Strap until Strap
reaches full length as
shown in Figure 10.
Option 2: If Q-Tether Adjuster
is on correct side of Splitter
Plate:
• Attach loop at end
of Q-Tether Strap by
sliding looped end into
slot in Splitter Plate as
shown in Figure 8.
• Remove one loop at
end of Q-Tether Strap
from Splitter Plate
by sliding strap out
through slot in Splitter
Plate as shown in
Figure 9.
Figure 10
Figure 9
Figure 8
Step 6
Open both Forward-Facing
Belt Lock-offs as shown in
Figure 11.
Step 7
Route looped end of
Q-Tether Strap through
Forward-Facing Belt Path,
taking care that Q-Tether
Strap is NOT between
the Harness and seat, as
shown in Figure 12.
Step 8
IMPORTANT: Check that
Q-Tether Strap is flat and not
twisted before attaching loop
to Splitter Plate.
Attach loop at end of Q-Tether
Strap to Splitter Plate by
sliding Strap into slot in Splitter
Plate as shown in Figure 13.
Figure 11
Figure 12
Figure 13
Step 9
Pull free end of Q-Tether
Connector Strap until
Splitter Plate is positioned
on top of vehicle seat back
as shown in Figure 14.
IMPORTANT: To prevent
injury to the child in a
sudden stop or crash
Splitter Plate MUST be
positioned on top of
vehicle seat back and
never in front of vehicle
seat back where the child’s
head could strike as shown
in Figure 15. Contact Clek
Customer Service at
1-866-656-2462 if unable
to obtain correct position
of Splitter Plate.
Figure 14
Figure 15
Tabla de contenidos
Otros manuales de Asiento de coche de Clek
Clek
Clek FLLO Manual de usuario
Clek
Clek Olli Manual de usuario
Clek
Clek Olli Manual de usuario
Clek
Clek FOONF Manual de usuario
Clek
Clek Foonf 2017 Manual de usuario
Clek
Clek Oobr Manual de usuario
Clek
Clek Oobr Manual de usuario
Clek
Clek Infant-Thingy Manual de usuario
Clek
Clek FOONF Manual de usuario
Clek
Clek FOONF Diagrama de cableado
Clek
Clek FOONF Manual de usuario
Clek
Clek Liing Manual de usuario
Clek
Clek Liingo Manual de usuario
Clek
Clek FOONF Manual de usuario
Clek
Clek Car Seat Manual de usuario
Clek
Clek Oobr Manual de usuario
Clek
Clek FOONF Manual de usuario
Clek
Clek Olli Manual de usuario
Clek
Clek Olli Manual de usuario
Clek
Clek FOONF Manual de usuario
