Clearaudio Innovation Wood Manual de usuario
Innovation
Clearaudio electronic®GmbH
Spardorfer Str. 150 • D-91054 Erlangen • Tel. +49 9131 40300100 • FAX + 49 9131 40300119
www.clearaudio.de • www.analogshop.de • info@clearaudio.de
© Clearaudio electronic GmbH 2016
Version: 2.5_13.10.2016_E
User manual
Made in Germany
Innovation
Innovation Wood
Picture: Package with
Clearaudio tonearm „TT3“
and Clearaudio cartridge
„Titanium V2 “.
Picture: Package with
Clearaudio tonearm
„Universal“ and Clearaudio
cartridge „da Vinci V2 “.
Dear Clearaudio customer,
Congratulation’s to your choice of the
Innovation / Innovation Wood
(in the following:
Innovation
named)
turntable, a world class turntable, handmade in Germany by Clearaudio electronic GmbH.
Resonance minimizing chassis construction in a sandwich in combination with the innovative motor unit
(low noise level and high turning moments), guarantees total isolation of resonances from the turntable
chassis, providing the best music reproduction and authentic High End imaging. A high precision,
maintenance free sinter bronze bearing is completing the analogue pleasure.
The Clearaudio patented CMB-Bearing-Technology, an inverted bearing with jewelled and polished
ceramic bearing shaft and a bronzed liner, provides frictionless analog enjoyment.
Please read this instruction manual carefully, to avoid any damages or loss of warranty.
This manual will help you for an easy setup and guarantees the highest pleasure for a long time.
We wish you a lot of musical enjoyments with your new Clearaudio
Innovation
turntable.
Clearaudio electronic GmbH
This section must be read before any connection is made to the mains supply.
Innovation
User manual
WARNINGS
Don’t expose your turntable to rain or humidity.
Don’t handle the mains leads with wet hands.
Don’t place or insert anything into the equipment or through ventilation holes.
No naked ame sources, such as lighted candles, should be placed on the equipment.
CE-MARKING
EQUIPMENT MAINS WORKING SETTING
Your Clearaudio product has been prepared to comply with the household power and safety requirements
that exist in your area. This product can be connected to 230 V or 110 V AC (50 Hz and 60 Hz).
COPYRIGHT
Recording und reproduction of any sound-material may require the consent of the creator. Please acknow-
ledge the information given in the
- Copyright Act 1956,
- Dramatic and Musical Performers Act 1958,
- Performers Protection Acts 1963 and 1972,
- Any more recent legal regulations.
Page 2 © Clearaudio electronic GmbH 2016
The Clearaudio
Innovation
meets the regulations concerning electromagnetic disturbance
(EMC) and low-voltage appliances.
Contents
1. Packing overview 4
2. List of components 5 - 6
3. Installation and setup 7 - 12
4. Fine adjustment of the motor 13
5. Service and special instruction 14
6. Technical data 15
Warranty information 16
Stroboscope Testrecord user manual 17 -18
Page 3© Clearaudio electronic GmbH 2016
Innovation
User manual
1. Packing overview
Page 4 © Clearaudio electronic GmbH 2016
Pic. 1: Packing overview
Accessories,
user manual,
warranty card,
Clearaudio Quality
Card,
Stroboscope Testrecord
Innovation
turntable chassis incl.
mounted lower bearing
part and integrated
motor unit;
optional: Tonearm
Stainless steel-sub-
platter; Delrin or Acrylic
platter;
power supply;
upper bearing part and
– cap
optional: Cartridge
Innovation
User manual
2. List of components
Clearaudio has developed a special and secure packing for your
Innovation
turntable that ensures a safe
transportation.
Please keep this original packing, if you need to ship the turntable.
Below you nd the part list of the Clearaudio
Innovation
turntable:
Page 5© Clearaudio electronic GmbH 2016
Pic. 2: List of components
123
4
7a 7b
1. Turntable body with mounted lower
bearing part 5. Bearing part
2. Stainless steel sub-platter 6. 3 x Flat Pads
3. Delrin or Acrylic (Wood version)
turntable platter 7. Optional: Clearaudio
Universal
(7 a) or
Magnify
(7 b) tonearm with counterweight to
adjust the tracking force
4. Power supply 8. Mounting clip for stainless steel sub-platter and
hex key
Pic. 7b: Clearaudio
Magnify
tonearm
Pic. 7a: Clearaudio
Universal
tonearm
56
8
Innovation
User manual
Continuation of components list
Page 6 © Clearaudio electronic GmbH 2016
910 11
12 13 14
15 16 a 17
9. 1 Pair of white gloves 15. Bearing oil for occasional use
10. Grounding - wire for the Innovation
turntable (to connect in the bottom
bearing part) 16 a
16 b
Optional in package:
Clearaudio MC cartridge
da Vinci
Clearaudio MC cartridge
Talismann
Clearaudio
Smart Stylus Gauge
11. Level gauge for the turntable
alignment
17. Clearaudio
Stroboscope Testrecord
(Art. No. AC038) to adjust the exact speed
12. 1 pcs. at belt 18. Optional in package:
Turntable + tonearm + cartridge
No illustration:
Cartridge alignment gauge
for
Unify
or
Universal
tonearm (optional)
13. 4 pcs. hex wrench; sizes: #1,5; #
2,5; #3; #7
19. Not shown: warranty card, Clearaudio Quality
Card, Sales return paper
14. Screw driver 17. Not shown: User Manual
Pic. 2.1: List of components
IMPORTANT NOTICE:
Please double check the tightness of all bolts, hardware, and mounting pods, as temperature uctuations
during transit may have caused the hardware to become loose.
16 b
Innovation
User manual
Page 7© Clearaudio electronic GmbH 2016
3. Installation and setup
The setup of the
Innovation
turntable is easy as the turntable chassis is pre-assembled and has been
tested at the factory.
Please use the white gloves enclosed in order to avoid scratches or unwanted ngerprints (platter).
The
Innovation
turntable requires a space for setup of at least 18.90 inch x 19.29 inch.
18.90 inch
/ 480 mm
19.29 inch / 490 mm
Pic. 3: Required set - up space
Innovation
User manual
Page 8 © Clearaudio electronic GmbH 2016
Please follow the description step by step:
1.)
First take out the three black at pads out of the accessory bag.
Place these at pads on your hi-rack or another suitable base, where the nal position of your
Innovation
turntable will be.
2.)
After that, take the Innovation turntable body of the next packing layer and place the spikes of the
turntable on the at pads.
Pic. 4:
Innovation
with tonearm base
Pic. 6: Oiling the bearing shaft
3.)
To avoid hum noises it can be necessary to ground the bearing. For that please plug in the provided ground
cable into the hole of the screw from the bearing at the bottom side of the turntable.
Pic. 5: Grounding the bearing of the
Innovation
4.)
Remove the protective security tape from the bearing housing.
Place two drops of the synthetic bearing oil on the ceramic bearing shaft.
(also available at www.analogshop.de, Art. No. AC068)
Innovation
User manual
Page 9
© Clearaudio electronic GmbH 2016
5.)
Take the stainless steel platter with both hands carefully out of the box.
Remove the lamination of the scale ring on the lower side of the turntable.
Please remove the lamination extreme carefully and avoid any soiling and scratches.
Push the delivered bearing part carefully through the hole in the stainless steel sub-platter and mount the
bearing part with the sub-platter by using the mounting clip.
6.)
In the next step remove the lamination of the sensor, mounted on the turntable chassis (picture 6: red
frame).
Please remove the lamination extreme carefully and avoid any soiling and scratches.
Pic. 7: Connection sub-platter and bearing upper part
Pic. 8: Removing the lamination
7.)
With both hands you can place the stainless steel platter
carefully onto the bearing.
Through a lightly (!!) up and down movement the platter will
slip onto the bearing upper part (picture 8).
Make sure with gentle pressure that the platter is applying on
the complete surface of the bearing.
Avoid major side forces to avoid any damages to the
ceramic bearing!
Pic. 9: Setup stainless steel platter with
upper bearing part
Innovation
User manual
Page 10 © Clearaudio electronic GmbH 2016
8.)
Now you can remove the mounting clip with the delivered hex wrench.
9.)
Take the Delrin platter with both hands out of the box and set
the platter carefully onto the bearing.
The at side of the platter should face to the stainless steel
platter and the side with the cut-out (for the record) should
face up.
To avoid any damages on your bearing, the Delrin platter
should have room temperature before the setup begins
(approx. 20 ° Celsius).
Avoid major side forces to avoid any damages to the
ceramic bearing!
Pic. 10: Removing of the mounting clip
Pic. 11: Setup Delrin platter and bearing cap
You will nd suitable adjustment equipment under www.clearaudio.de or www.analogshop.de.
10.)
To install the tonearm, please follow the user manual of the manufacturer.
Innovation
User manual
Otros manuales para Innovation Wood
1
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Placa giratoria de Clearaudio
Clearaudio
Clearaudio Ovation Manual de usuario
Clearaudio
Clearaudio Master Solution Manual de usuario
Clearaudio
Clearaudio Ovation Manual de usuario
Clearaudio
Clearaudio Statement V2 Manual de usuario
Clearaudio
Clearaudio Concept Manual de usuario
Clearaudio
Clearaudio Satisfy Kardan Manual de usuario
Clearaudio
Clearaudio Magnify Manual de usuario
Clearaudio
Clearaudio Innovation Wood Manual de usuario
Clearaudio
Clearaudio Jubilee MM Manual de usuario
Clearaudio
Clearaudio concept V2 Manual de usuario
Clearaudio
Clearaudio Perfomance SE Manual de usuario
Clearaudio
Clearaudio Stroboscope Testrecord Manual de usuario
Clearaudio
Clearaudio Emotion SE Manual de usuario
Clearaudio
Clearaudio Concept Manual de usuario
Clearaudio
Clearaudio Turbo Weight Manual de usuario
Clearaudio
Clearaudio TT1 MI Manual de usuario
Clearaudio
Clearaudio Peerformance Manual de usuario
Clearaudio
Clearaudio Emotion Start Smart Manual de usuario
Clearaudio
Clearaudio Unify Manual de usuario
Clearaudio
Clearaudio Charisma V2 MM Manual de usuario
