Clear One BMA CTH Manual de usuario

COLLABORATE® Versa™ Room CT 160

Quick-Start Guide

COLLABORATE® Versa™ Room CT 160

1QSG-0169-001v1.0 May 2023

Quick-Start Guide

Notices

Information in this document is subject to change without notice.

Document: QSG-0169-001v1.0, May 2023

1. Read, follow, and keep all instructions.

2. Do not use these devices near water.

3. Clean only with dry cloth.

4. Do not block any ventilation openings. Install in accordance with manufacturer instructions.

5. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that

produce heat.

6. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the

other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your

safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

7. Protect the PoE injector’s power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the

point where they exit from the apparatus.

8. Only use attachments/accessories specified by the manufacturer.

9. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

10. Unplug this apparatus during lightning storms or when unused for long periods of time.

11. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as

power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate normally, or has been dropped.

12. Disconnect the apparatus from the AC mains with the mains plug. This plug shall remain readily operable.

13. Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out

parts that could result in fire or electric shock.

14. This product can interfere with electrical equipment such as tape recorders, TV sets, radios, computers and microwave ovens if

placed in close proximity.

15. Class 2 Wiring IS REQUIRED. Only qualified personnel should wire and install.

16. Underwriters Laboratories (UL) requires these safety notifications:

Important Safety Information

ClearOne®Contacts

Headquarters Headquarters

5225 Wiley Post Way Suite 500 Tel: +1.801.975-7200

Salt Lake City, UT 84116

Sales Technical Support

Tel: +1.801.975.7200 Tel: +1.801.974.3760

[email protected] [email protected]

COLLABORATE® Versa™ Room CT 160

2QSG-0169-001v1.0 May 2023

Quick-Start Guide

Operating Requirements

System Power and Thermal

• Power Type: PoE/PoE+

• Port Type: RJ-45

• PoE In/P-Link In: 802.3af or 802.3at PoE/PoE+

• Power Source: PoE Injector or equivalent

• PoE: IEEE 802.3at compliant devices providing 56V and 640 mA (36 W).

• P-Link In - Mode B

Power Consumption

• 100-240VAC, 50/60Hz, 3 Watts Typical

• 38W at max power 1kHz (2 x 10W)

• Thermal: 130 BTU/Hr at max power

• Operating Temperature: 14° F/-10° C to 104° F/40° C ambient temperature

System Part Number

• 930-3200-020-U - COLLABORATE Versa Room CT

• 930-3200-020-I - COLLABORATE Versa Room CT INTL

Packing List

Verify that you have received all parts associated with each of the following components:

Inspect your shipment carefully.

If the shipment shows obvious signs of damage, retain original boxes and packing material for inspection by the carrier,

and contact the carrier immediately.

ClearOne is not responsible for product damage incurred during shipment.

1. BMA CTH

2. Versa USB

3. PoE (Injector) Kit

4. CONVERGE®Versa Hub

5. UNITE 160 4K Camera

6. Ceiling Loudspeakers

7. Cables

WARNING: TO

PREVENT FIRE

ELECTRICAL

SHOCK

HAZARD, DO

NOT EXPOSE

THIS

PRODUCT TO

RAIN OR

MOISTURE

THE LIGHTING FLASH

AND ARROWHEAD

WITHIN THE TRIANGE IS

A WARNING SIGN

ALERTING YOU OF

DANGEROUS VOLTAGE

INSIDE THE PRODUCT.

THE EXCLAMATION POINT

WITHIN THE TRIANGLE IS A

WARNING SIGN ALERTING

YOU OF IMPORTANT

INSTRUCTIONS

ACCOMPANYING THE

PRODUCT.

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR BACK)

NO USER SERVICEABLE PARTS INSIDE. REFER

SERVICING TO QUALIFIED SERVICE PERSONNEL.

SEE MARKING ON BOTTOM/BACK OF PRODUCT

RISK OF ELECTRIC SHOCK DO

NOT OPEN

AVIS RISQUE DU CHOC ELECTRIQUE

- NE PAS OUVRIR

Use only in

non-tropical

locations.

Use only at

altitudes of

2000 meters

or less.

CAUTION

COLLABORATE® Versa™ Room CT 160

3QSG-0169-001v1.0 May 2023

Quick-Start Guide

3. PoE (Injector) Kit

CAT6 cable,

Black, 25 ft. (1)

CAT6 cable,

Blue, 25 ft. (1)

Power

cord, 6 ft.

Power

supply

4. COLLABORATE Versa Hub

Versa Hub

Power

supply

DVI-VGA

adapter USB 3.0 Cable Type

B to Type A, 3ft

Does not require a Quick-Start Guide

5. UNITE 160 4K Camera

USB 3.0 Cable Type

C to Type A, 5ft

Power Supply

Includes UNITE 160 Camera Quick-Start Guide

6. Ceiling Loudspeakers (2)

7. Cables

CAT6 cable,

50 ft. (1)

USB extender

cable, 33 ft.

Includes installation

instructions and ceiling tile

cutout template

1. BMA CTH

BMA CTH Plenum

shield (1)

2. Versa USB

Versa USB USB Cable

600-to-625

mm adapter

(4)

Camera

COLLABORATE® Versa™ Room CT 160

4QSG-0169-001v1.0 May 2023

Quick-Start Guide

Basic Versa Room CT 160 Connections

The steps listed below and the accompanying illustration describe how to connect your Versa Lite.

1. Connect the PoE injector to the

Versa USB PoE In port.

2. On the Versa USB, move the

Power Select switch to the PoE

In position.

3. Connect the Versa USB P-Link

Out port to the BMA CTH P-Link

In port.

4. On the BMA CTH, move the

Power Select switch to the

P-Link In position.

5. Connect the Versa USB Audio

port to a Versa Hub USB port.

6. Connect the Versa Hub’s USB

In port to your PC’s USB port.

Mount the Components

BMA - CTH

1. On the BMA CTH back panel, do the following:

• With speaker wire (not included), connect the two loudspeakers to the Phoenix Euroblock connectors (a)

• Move the Power Select sliding switch (b) to the right, towards the P-Link In connector (c)

2. Complete the steps indicated in the BMA Surface Mount Kit Installation Guide

adc

COLLABORATE® Versa™ Room CT 160

5QSG-0169-001v1.0 May 2023

Quick-Start Guide

Required Tools

Bottom Side of a Table Top Mount

Select your hardware based on your specific installation needs.

1. Determine the location for the Versa Hub.

2. Use a pencil to mark on the table the location of four mounting holes

that align with the mounting holes on the Versa USB mounting ears.

3. Determine the proper depth and diameter for the holes.

4. Drill four pilot holes for #6 or M3.5 screws.

5. Align the mounting holes on the Versa USB mounting ears with the

pilot holes.

6. Use four #6 or M3.5 screws to attach the Versa Hub to the table.

• No. 1 Phillips screwdriver

• T15 Torx screwdriver

• Level (to level the Versa USB)

• Drill bits appropriate for anchors

• Electric drill

• Drywall saw (for cutting hole in wall or ceiling)

Wall Mount

Select your hardware based on your specific installation needs.

1. Determine location for the Versa USB.

2. Use a pencil to mark on the table the location of four mounting holes that align with the mounting holes on the

Versa USB mounting ears. If needed, use a level.

3. With the proper size drill bits, drill four pilot holes for fasteners/anchors.

4. Install the fasteners/anchors in the wall.

5. Align the mounting holes on the Versa USB mounting ears with the pilot holes.

6. Use four #6 or M3.5 screws to attach the Versa Hub to the wall.

Note: Anchors and screws to mount the Versa USB are not provided. The installer must select them for the wall

material that supports the unit. Exercise care when you drill and install anchors so wall material does not tear out

and weaken the attachment.

Versa USB

You can mount the Versa USB in the following ways:

Note: Mounting hardware such as screws and anchors are not included with the Versa USB.

Standard Equipment Rack Mount

ClearOne offers a standard 1U rack shelf with 20 lb (9kg) weight capacity.

1. Determine location for rack shelf.

2. Align mounting holes on rack shelf mounting ears with holes on the rack (at determined location).

3. Insert the four #10-32 screws included with the ClearOne 1U rack shelf (or proper screws for your third-party

mount) and tighten.

Note: Remove pre-installed mounting ears on expander to fit up to 3 Versa USB units side-by-side on a single

ClearOne 1U rack shelf.

4. Torx drive screws secure the pre-installed mounting ears to the main body of

the Versa USB. Remove them with a Torx T15 screwdriver. (optional)

5. Secure the Versa USB to the rack shelf. You must supply your own hardware

(four #6 or M3.5 screws) for securing the Versa USB.

• Standard equipment rack

• Bottom side of a table top

• On a wall

• Above the ceiling

COLLABORATE® Versa™ Room CT 160

6QSG-0169-001v1.0 May 2023

Quick-Start Guide

Mount the Versa Hub, UNITE 160 4K Camera, and Ceiling Loudspeakers

Follow the instructions in the respective Quick-Start or Installation Guide (included).

Above the Ceiling Mount

Select hardware based on your specific installation needs.

Note: It is the installer’s responsibility to ensure that the installation and cable routing complies with local safety

codes.

1. Determine location for the mount, and where to route cables.

Mark location where you want to route cables through with a pencil (on finished side of ceiling tile) if you need to

cut a hole.

2. Remove affected ceiling tile and adjacent tiles required for access.

3. Install fasteners/anchors.

4. Install the Versa USB at determined location.

5. Use a drywall saw to cut a hole into finished side of ceiling tile at marked location.

6. Route the cables through the hole.

Note the following:

• Carefully run connected cables so they do not block the cooling vents or put strain on the connectors.

• Anchors and screws used to mount the Versa USB are not provided and must be selected by installer for the

type of ceiling material supporting the unit. Take care while drilling and installing anchors so ceiling material

does not tear out and weaken attachment.

Connect the Components

Warning:

Power over Ethernet (PoE) equipment used with Xceed BMA Room must meet the IEEE 802.3af or 802.3at

standards.

You should use the PoE Power Injector provided with Xceed BMA Room. Other power source equipment may

immediately apply power and could damage the Xceed BMA Room components.

Complete step 1 NOW if you did not when you installed the BMA CTH with the surface mount kit.

1. On the BMA CTH back panel, do the following:

• With speaker wire (not included), connect the two loudspeakers to the Phoenix Euroblock connectors (a)

• Move the Power Select sliding switch (b) to the right, towards the P-Link In connector (c)

2. On the Versa USB, set the Power select switch (h) towards PoE In.

adc

COLLABORATE® Versa™ Room CT 160

7QSG-0169-001v1.0 May 2023

Quick-Start Guide

3. With a 50’ CAT6 cable (provided), connect the BMA CTH P-Link In connector (c) to the Versa USB P-Link Out

connector (g).

4. Optional

If your system includes a Bluetooth expander (available separately), complete this step.

If not, skip this step and proceed to step 5.

With a CAT6 cable (not included):

Connect the BMA CTH P-Link Out connector (d) to the Bluetooth Expander.

5. With one of the included 25 ft. CAT6 cables, connect

the Versa USB PoE In connecter (i) to the PoE injector

connector (j).

6. With the provided USB cable, connect the Versa USB Audio connector (e) to the Versa Hub USB connector (m)

(any one of the four).

7. As needed, use the provided 33 ft. USB extender cable to connect the UNITE camera to the Versa Hub connector

(l) (either of the two).

8. Connect the Versa Hub 12 VDC power connector (k) to a standard power outlet.

9. Caution: Complete this connection step only after you confirm that you correctly completed the previous steps!

With the PoE Injector:

• Attach the power cord to the power supply.

• Connect the power cord to a standard power outlet.

klm

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sistema de conferencias de Clear One

Clear One

Clear One VERSA 20 Manual de usuario

Clear One

Clear One collaborate pro 600 Manual de usuario

Clear One

Clear One COLLABORATE Live 600 Manual de usuario

Clear One

Clear One ClearOne RAV 600 Manual de usuario

Clear One

Clear One Collaborate Manual de usuario

Clear One

Clear One ClearOne RAV 600 Manual de usuario

Clear One

Clear One Collaborate Manual de usuario

Clear One

Clear One Converge Pro 840T Manual de usuario

Clear One

Clear One Converge Pro 880 Instrucciones de instalación

Clear One

Clear One Converge Pro TH20 Manual de usuario

Clear One

Clear One CONVERGE Pro 2 (CP2) Series Manual de usuario

Clear One

Clear One COLLABORATE Live 600 Manual de usuario

Clear One

Clear One Aura VERSA 150 Manual de usuario

Clear One

Clear One COLLABORATE ROOM Series Manual de usuario

Clear One

Clear One COLLABORATE Pro 300 Manual de usuario

Clear One

Clear One UNITE 160 Manual de usuario

Clear One

Clear One XAP TH2 Manual de usuario

Clear One

Clear One MAX EX Manual de usuario

Clear One

Clear One COLLABORATE Versa Lite CT Manual de usuario

Clear One

Clear One XAP 800 Manual de usuario

Clear One

Clear One MAX IP Response Point Manual de servicio

Clear One

Clear One MAX WIRELESS Manual de usuario

Clear One

Clear One AP800 Manual de usuario

Clear One

Clear One Aura VERSA PRO 50 Manual de usuario

Manuales populares de Sistema de conferencias de otras marcas

Kramer

Kramer VIA GO Manual de usuario

AVT

AVT MAGIC AC1 Go Manual de usuario

ProSoft Technology

ProSoft Technology AN-X4-AB-DHRIO Manual de usuario

Sony

Sony PCS-I150 Manual de usuario

Middle Atlantic Products

Middle Atlantic Products VTC Series Manual de usuario

Prentke Romich Company

Prentke Romich Company Vanguard Plus Guía

Speakerbus

Speakerbus iD 712 Manual de usuario

Trelleborg

Trelleborg SafePilot CAT PRO Manual de usuario

Sennheiser

Sennheiser ADN Manual de usuario

ADTRAN

ADTRAN NetVanta 7100 Manual de usuario

AINA

AINA PTT Voice Responder Manual de usuario

Yamaha

Yamaha ProjectPhone PJP-100H Manual de usuario

vissonic

vissonic VLI Series Manual de usuario

Panasonic

Panasonic KX-VC500 Manual de usuario

Poly

Poly Trio 8300 Manual de usuario

Crestron

Crestron Mercury CCS-UCA-SMK Dibujo dimensional

Inmarsat

Inmarsat mini M Manual de usuario

Tenveo

Tenveo ALL-IN-ONE Manual de usuario