Clean Water Systems 7500-M Manual de usuario

7500-M Sediment Filter Installation Guide

Thank you for purchasing a Clean Water System! With proper installation and a

little routine maintenance your system will be providing Sediment free water for

many years.

Please review this start‐up guide entirely before beginning to install your system,

and follow the steps outlined for best results.

Minimum pressure of 30 PSI recommended.

Maximum pressure recommended 80 PSI.

For indoor installation only.

Protect from sunlight, rain, and freezing.

SEDIMENT MEDIA CONTAINS DUST.

USE MASK TO AVOID BREATHING DUST.

OK to wet down media with spray bottle

Questions?

Call us toll‐free: 1‐888‐600‐5426 or 1‐831‐462‐8500

Email us: [email protected]

See more information on our website: www.cleanwaterstore.com/resources

Clean Water Made Easy

www.cleanwaterstore.com

Table of Contents

Packing Lists .................................................................................................................................................. 3

Pre‐Installation.............................................................................................................................................. 4

Best Practices for Piping & Drain Installation: .............................................................................................. 4

Installation of Your System in Copper or Metal Piping Systems:.................................................................. 5

How Your Sediment Filter Works:................................................................................................................. 6

Assembly and Installation Instructions:........................................................................................................ 7

Programming Your Valve and Setting Time and Days for Backwash............................................................ 8

Initial Backwash .......................................................................................................................................... 10

Maintenance: .............................................................................................................................................. 11

Troubleshooting the 7500‐M Sediment Filter: ........................................................................................... 11

7500-M Sediment Filter Installation & Startup Guide

3www.cleanwaterstore.com 042021

Packing Lists

All systems include:

7500‐M control valve, 3 female NPT to BSP black pipe adapters, power supply, funnel for adding

media, top screen, start‐up guide, and items included in one of the following options:

Find Your Size System to See What is Included:

What to Do if Your Tank is Not Level Out of the Box:

Your black filter tank base is not glued to the bottom of your tank. Occasionally tank bases will become

crooked during shipment. If you find that that your tank does not sit level on the floor, you can easily

adjust it by holding the empty tank and knocking it on a concrete or solid floor once or twice to level it.

Sediment Filter 0.75 cubic foot size

8” x 44” filter tank with distributor tube

8 lbs. filter gravel

0.75 cubic foot of Sediment Media

Sediment Filter 1.0 cubic foot size

9” x 48” filter tank with distributor tube

12 lbs. filter gravel

1 cubic foot of Sediment Media

Sediment Filter 1.5 cubic foot size

10” x 54” filter tank with distributor tube

16 lbs. Filter gravel

1.5 cubic foot of Sediment Media

Sediment Filter 2.0 cubic foot size

12” x 52” filter tank with distributor tube

20 lbs. filter gravel

2.0 cubic foot of Sediment Media

Sediment Filter 2.5 cubic foot size

13” x 54” filter tank with distributor tube

35 lbs. filter gravel

2.5 cubic foot of Sediment Media

Sediment Filter 3.0 cubic foot size

14” x 65” filter tank with distributor tube

40 lbs. filter gravel

3.0 cubic foot of Sediment Media

7500-M Sediment Filter Installation & Startup Guide

4www.cleanwaterstore.com 042021

Pre-Installation

1. Review your packing list and make sure you have received all the parts before installation.

2. If you are going to be turning off the water to the house and you have an electric water heater,

shut off the power to the water heater before beginning installation in case water heater is

accidentally drained.

3. Pick a suitable location for your filter system on a dry level spot where it won’t be exposed to

freezing temperatures. A minimum of 20 PSI is required. Maximum pressure is 90 PSI.

4. Get all of your plumbing parts together before beginning installation, and make sure you have

received all of your packages before beginning or scheduling an installation. Installation typically

takes 3 to 5 hours. However, after installation the Sediment Filter must be allowed to run

through a complete backwash and rinse cycle.

5. After the system is installed and running, your water may be discolored, or full of sediment or

rust, particularly if this is older or corroded piping. This typically clears up over a day or two.

Best Practices for Piping & Drain Installation:

1. Make sure to connect the Inlet from your water source and outlet, following arrows on control

valve. Connect the External Flow Control fitting onto the Drain

line. You must use the 3 female pipe adapters provided.

Assemble all fittings into valve fitting prior to installion to the

head. These seal with the blue seals and if overtightened can

damage the valve body.

2. Make sure there is a working gate or ball valve before the 7500

Filter System and also one after as well as a bypass valve. A hose

bib (which is a faucet to which you can attach a garden hose) is

strongly recommended after the Sediment Filter and before the

second ball valve. This makes it easy to rinse your new Sediment

Filter on start‐up and gives you a place to test the water.

3. If you will be using copper piping, do not sweat the copper pipe

directly on to the 7500‐M control valve.

4. You should install unions and a bypass around the valve, so that you can remove it and still have

water (See Build Your Bypass).

5. To connect drain line to drain, use an air‐gap connection, so that if your sewer or septic tank

backs up, it cannot cross connect with the drain tubing.

7500-M Sediment Filter Installation & Startup Guide

5www.cleanwaterstore.com 042021

Installation of Your System in Copper or Metal Piping Systems:

If your new filter system is to be installed in a metal (conductive) plumbing system, i.e. copper or

galvanized steel pipe, the plastic components of the system will interrupt the electrical continuity of the

plumbing system.

As a result, any stray currents from improperly grounded appliances downstream or potential galvanic

activity in the plumbing system can no longer ground through the contiguous metal plumbing.

Some homes may have been built in accordance with building codes, which encouraged the grounding

of electrical appliances through the plumbing system.

Consequently, the installation of a bypass consisting of the same material as the existing plumbing, or a

grounded "jumper wire" bridging the equipment and reestablishing the contiguous conductive nature of

the plumbing system must be installed prior to your systems use.

This is simple and easy step to take if you are installing your water treatment system into copper

piping. A simple ground jumper wire with a pipe clamp can be purchased at any Home Center, or

hardware store etc. for a few dollars.

7500-M Sediment Filter Installation & Startup Guide

6www.cleanwaterstore.com 042021

How Your Sediment Filter Works:

Water enters the top of the tank and

flows down through the media and up

the distributor tube.

The backwashing Sediment Filter

removes sediment and is automatically

backwashed.

This cleans and re‐classifies the

Sediment, preventing channeling.

During backwash the flow of water is

reversed and water flows down the

distributor tube and up through the

media, lifting and expanding the

Sediment media.

During the backwash the Sediment is

cleaned by the action of the water

flowing through it.

7500-M Sediment Filter Installation & Startup Guide

7www.cleanwaterstore.com 042021

Assembly and Installation Instructions:

1. Wrap the top of distributor tube with electrical or duct tape so

that no gravel or Sediment media will go down the distributor

tube when adding the media.

2. Add the filter gravel that came with your order. You want the

gravel to cover the bottom distributor screen before adding the

Sediment media.

3. Next add Sediment media. The tank should be about 2/3rds full

of media, do not fill more than 2/3rds, even if there is some

media left over.

4. Remove cap or tape from top of distributor tube. Be careful not to pull up distributor tube when

removing cap or tape.

5. Fill tank completely with water. This will allow the Sediment Filter media to settle and reduce the

need of purging the air out of the tank later.

6. Add a small amount of silicone grease to the inner O‐ring, where the distribution tube goes. Next,

install the top screen (This is a funnel‐shaped plastic screen that locks into the control valve and

prevents resin from being backwashed out to drain during the regeneration cycles.).

7. Lubricate the main tank O‐ring and screw on 7500 control valve carefully. Do not use pipe‐joint

compound, vegetable oil, Teflon tape, or Vaseline or other petroleum greases to lubricate tank

threads.

Next, you will need to program the system and set the time of day.

7500-M Sediment Filter Installation & Startup Guide

8www.cleanwaterstore.com 042021

Programming Your Valve and Setting Time and Days for Backwash

Next, you will need to program the system to work as a Sediment Filter. There are a few settings that

must be changed before the system can be put into service. Plug in the control valve and begin the

programming instructions.

*IMPORTANT*: Before any operation, the valve menu must be unlocked. If the button lock

indicator is displayed, press and hold both the Up and Down buttons for 5 seconds. A sound will

indicate the menu is unlocked. The menu will re‐lock automatically after 1 minute of inactivity.

1. To begin programming your valve, unlock the menu and press the Menu/Confirm button. This

puts the valve into program display mode, indicated by the Enquiry/Setting icon being

displayed. The Enquiry/Setting icon is displayed whenever you are changing the parameter

of a programming mode.

2. The sequence of programming modes is shown in the diagram below. To switch between

modes, press the up or down button according to which direction your mode is. The modes

can only be changed when the Enquiry/Setting button is displayed and you are not currently

modifying any other parameter.

7500-M Sediment Filter Installation & Startup Guide

9www.cleanwaterstore.com 042021

1) To change the Time of Day:

Change programming mode to Time of Day ( [00:00] and time of day icon displayed ). The hour

and Enquiry/Setting icon will be flashing. Change the hour value with the Up/Down buttons,

then press Menu/Confirm to move onto the minute value. Change this value with Up/Down,

and press Menu/Confirm again to confirm the time.

2) To change the Rinsing Time:

The rinsing time is the hour of day that the system will turn on to perform its function. We

recommend setting the system to backwash at 2 AM [02:00], or any time that it is unlikely any

water will be used. Note the valve uses the 24‐hour clock.

The default setting is [02:00]. The max setting is [23:59]. To change, set the programming mode

to Rinsing Time ( [00:00] ). Press the Menu/Confirm button and use the Up/Down buttons to

change the hour value. Press the Menu/Confirm button again and change the minute value

using the Up/Down buttons. Finally, press Menu/Confirm to confirm your rinse time.

3) To change the Rinsing Frequency:

The rinsing frequency is how many times the system will backwash and rinse per service.

This should be left at its default, [F-00]. This will have the system only backwash and rinse once

per service.

4) To change the Service Days:

5) The recommended initial backwash frequency setting for the Sediment Backwash Filter is

every 3 to 4 days for families or heavy use and every 7 days for 1 to 2 persons in the home.

If you experience pressure loss in between backwashes, increase frequency of backwash up

to once per day.

7500-M Sediment Filter Installation & Startup Guide

10 www.cleanwaterstore.com 042021

To set this, change the programming mode to Service Days ( [1‐03D] ). Press the Menu/Confirm

button and use the Up/Down buttons to set it to your desired amount. Press Menu/Confirm to

confirm your input.

6) To change the Backwash Time:

The backwash time is the amount of time (in minutes) that the system will backwash for.

For a neutralizer filter, set the backwash time to 10 minutes [2-10:00]. To change this, set the

programming mode to Backwash Time ( [2‐10:00] and backwash icon displayed ). Press the

Menu/Confirm button and use the Up/Down buttons to set it to [2-10:00]. Press Menu/Confirm

to confirm the backwash time.

7) To change the Fast Rinse Time:

The fast rinse time is the amount of time (in minutes) that the system will rinse for.

For a Sediment filter, set the fast rinse time to 6 minutes [3-06:00]. To change this, set the

programming mode to Fast Rinse Time ( [3‐10:00] and fast rinse icon displayed ). Press the

Menu/Confirm button and use the Up/Down buttons to set it to [3-06:00]. Press Menu/Confirm

to confirm the fast rinse time.

8) To change the Signal Output Mode

The signal output mode refers to when the system receives external function.

Leave this at its default, [b-01].

After configuring, press the Manual/Return button to exit programming mode.

Initial Backwash

1After programming, the system must be run through an initial backwash.

2Close inlet ball valve and outlet ball valve and open the bypass valve.

3Press the Manual/Return button to enter the backwashing cycle. When the backwash icon

is displayed, slowly open the inlet valve B to a quarter position to make the water flow into

the resin tank; you should be able to hear air escaping from the drain pipeline.

4After all the air is out of the pipeline, open inlet valve B and clean the foreign materials in

the tank until the water is clean.

5If possible, verify that the backwash flow corresponds with the size of your system below.

Otros manuales para 7500-M

Tabla de contenidos

Otros manuales de Sistema de filtración de agua de Clean Water Systems

Clean Water Systems

Clean Water Systems 5900e-AIR Manual de instalación

Clean Water Systems

Clean Water Systems Pro-OX 8500 Manual de instalación

Clean Water Systems

Clean Water Systems Tannin 5900e Series Manual de instalación

Clean Water Systems

Clean Water Systems Tannin 5900e Series Manual de instalación

Clean Water Systems

Clean Water Systems Pro?OX 2510 Manual de instalación

Clean Water Systems

Clean Water Systems Tannin 5900e Series Manual de instalación

Clean Water Systems

Clean Water Systems Tannin 5900e Series Manual de instalación

Clean Water Systems

Clean Water Systems CWS Plus Manual de instalación

Clean Water Systems

Clean Water Systems 7500-REV2.5 Manual de usuario

Clean Water Systems

Clean Water Systems Pro-OX Iron Filter 1650 with Chlorine Manual de instalación

Clean Water Systems

Clean Water Systems Pro-OX 7800 Manual de instalación

Clean Water Systems

Clean Water Systems 5900BT-SIDE-AIR Instrucciones de funcionamiento y seguridad

Clean Water Systems

Clean Water Systems 7500-M Manual de usuario

Clean Water Systems

Clean Water Systems Precision-24 Manual de usuario

Clean Water Systems

Clean Water Systems Greensand 7800 Manual de instalación

Clean Water Systems

Clean Water Systems Up-Flow Carbon Manual de instalación

Clean Water Systems

Clean Water Systems 7500-REV4 Manual de usuario

Clean Water Systems

Clean Water Systems 7500-REV4 Manual de usuario

Clean Water Systems

Clean Water Systems 7500-REV2.5 Manual de usuario

Clean Water Systems

Clean Water Systems 7500-C Manual de usuario

Clean Water Systems

Clean Water Systems Fleck 7000 Greensand Manual de instalación

Clean Water Systems

Clean Water Systems 5900-BT Tannin Filter Instrucciones de funcionamiento y seguridad

Clean Water Systems

Clean Water Systems Pro-OX 5700-E Manual de instalación

Clean Water Systems

Clean Water Systems Pro-Ox 5900-BT-AIR Series Instrucciones de funcionamiento y seguridad

Manuales populares de Sistema de filtración de agua de otras marcas

Wisy

Wisy LineAir 100 Manual de usuario

Schaffner

Schaffner Ecosine FN3446 Series Manual de funcionamiento

Pentair

Pentair FLECK 4600 SXT Guía del usuario

H2O International

H2O International H20-500 Manual de usuario

Renkforce

Renkforce 2306241 Manual de usuario

Neo-Pure

Neo-Pure TL3-A502 Manual de usuario

FLTR

FLTR OBF Manual de usuario

STA-RITE

STA-RITE VERTICAL GRID DE FILTERS S7D75 Manual de usuario

Applied Membranes

Applied Membranes W-G844EM Manual de usuario

BEGA

BEGA 116 Manual de usuario

WATA

WATA Standard Manual de usuario

Price

Price FFU series Manual

Gaggenau

Gaggenau BRITA INTENZA 467873 Manual de usuario

Brita

Brita SAFF-100 Manual de usuario

HEISSNER

HEISSNER FPU24000-00 Manual de usuario

BGS technic

BGS technic 1518 Manual de usuario

Reverse Osmosis

Reverse Osmosis RF Series Manual de usuario

ubbink

ubbink Filtramax Series Manual de usuario