Claudgen SCREENZONE RAC1306 Manual de usuario

41001187 Iss 07

Consort Equipment Products Limited

Thornton Industrial Estate, Milford Haven

CREEN

ONE

RECESSED WARM AIR CURTAINS

ATALOGUE

UM ERS

RAC1306, RAC1309

RAC1306RF

NSTALLATION

AND

PERATING

ANUAL

INDEX Section

General Information ------------------------------------------------------------- 1

Dimensions ------------------------------------------------------------------------ 2

Installation Details ---------------------------------------------------------------

Electrical Connection ----------------------------------------------------------- 4

Operation -------------------------------------------------------------------------- 5

Servicing & Maintenance ------------------------------------------------------ 6

41001187 Iss 07

1.5 RF Controller Location

It is essential the Controller should be positioned on

the wail in the same room as the aircurtain. It

should be where its temperature will not be change

with local effects. Avoid:

• Draughty places near windows or doors

• Places near the aircurtain itself or any other

heat sources in the room

• Place where the sun will shine on it

• Places where it may get wet

1.6 Controller standard models

The RAC1 06 and RAC1 09 heaters are supplied

with a remote controller. The remote control unit

houses single pole and 1 change over 10A rocker

switches. The controller is wired to the base unit via

0.75mm² 5 core PVC flexible cable.

1.7 Clearance Distances

It is recommended that a minimum clearance of

100mm is allowed around the case and 55mm

above. The clearance allows for cable entry and

prevents combustible surfaces overheating.

The minimum mounting height (floor to grille) is 2m.

The maximum mounting height is m.

1. General Information

1.1 Introduction

The heaters are designed for discreet positioning in

a suspended ceiling or bulkhead in the doorways of

retail or commercial premises. Overall energy sav-

ing is likely when the heater is sited above a fre-

quently opened external door as the airstream can

prevent heat loss. Will fit a recess as shallow as

195mm.

1.2 General

All installations must be in accordance with the

regulations in force in the country of use.

These instructions must be handed to the user on

completion of the installation.

Installers and service engineers must be able to

demonstrate competence and be suitably qualified

in accordance with the regulations in force in the

country of use.

To ensure continued and safe operation it is rec-

ommended that the appliance is serviced annu-

ally.

The heater outlet / inlet must not be obstructed dur-

ing use.

1.3 Electrical Supply

Electrical supply for RAC1 06 and RAC1 09 is ei-

ther 2 0V single phase or 415V three phase, Neu-

tral and Earth. Max cable inlet size is 4mm² for 1 - 4

terminals and 6mm² for L and N terminals.

Electrical supply for RAC1 06RF is 2 0V single

phase only. Max cable inlet size is 4mm².

It is recommended that the electrical supply to the

base unit in the air curtain is via an appropriate

switched isolator having a contact separation of

greater than mm on all poles.

BMS control, time switches, room thermostats and

door interlocks can be installed at the discretion and

responsibility of the installer.

All units must be wired in accordance with I.E.E

regulations for the Electrical Equipment of Build-

ings and the installer should ensure that a suitable

isolating switch is connected in the mains supply.

1.4 Controller `RF` models

The RAC1 06RF heater is supplied without a con-

troller. The `RF` models will not work without the

controller. There are three wireless controllers to

choose from in our range. See section 6.1 for more

details.

CLAUDGEN Wireless controllers

41001187 Iss 07

2. Dimensions

2.1 Air Curtain Dimensions

41001187 Iss 07

3. Installation Details

ENSURE AIR OUTLET LOUVRES ARE NEAREST

TO DOOR APPERTURE.

3. Installation Details

3.1 Location

All units should be installed horizontally directly

over the door opening. It is recommended that the

air curtain is installed on the inside of the building,

within the open room space against a wall or

ceiling.

Care must be taken to allow complete free air

movement into the inlet grilles of the unit to ensure

correct working operation of the air curtain. The

discharge opening should be as close to the top of

the door as possible and cover the entire door

width.

Units can be mounted adjacent to each other to

cover the full door opening across wider

entrances.

The weight of the RAC13 heaters is 17kg

3.2 Clearance Distance

It is recommended that a minimum clearance of

55mm is allowed around the case.

The minimum mounting height (floor to grille) is

1.8m. The recommended mounting height is 2.8m.

3.3 Health and Safety

Sole liability rests with the installer to ensure that

all site safety procedures are adhered to during

installation.

Sole liability rests with the installer to ensure that

protective safety wear such as hand, eye, ear and

head protection is used during installation of the

product.

Do not rest anything especially ladders against the

product.

Fig.1 Air discharge

Fig.2 Mounting cut out dimensions

Fig.3 Grille fixing

WARNING:

THIS AIR CURTAIN SHOULD NOT BE

INSTALLED WHERE THERE IS A

CORROSIVE ATMOSPHERE.

41001187 Iss 07

3.4 Installation

It is the sole responsibility of the installer to ensure

that the points of attachment to the building are

sound. Consultation with the consultant/architect or

owner of the building is recommended to ensure

that a sound, mechanically stable installation is

achieved.

Before fitting or wiring the air curtain, ensure the

outlet is facing the doorway as on the picture and

see the general installation guidance notes.

Using a pozidrive screwdriver slacken the two M5

screws in the corners near air inlet side and remove

the two M5 screws in opposite corner near the out-

let. Slide the lid sideways until the keyhole slots

pass over the screw heads. The grille assembly can

now be removed from the case.

Each unit has 2 fixing brackets from which it is sus-

pended. The brackets may be removed to assist in

passing the air curtain through the recess then reat-

tached when in-situ.

Either drop rods or catenary wire can be used to

fasten the air curtain to the ceiling support structure.

The height between the ceiling face and the top of

the air curtain case needs to be adjusted to circa

140mm to enable the grille assembly to fit flush with

the ceiling. Adjust accordingly.

After fitting the product in the ceiling recess and ad-

justing the height to ensure that the grille sits flush

to the ceiling (when re-fitted) take the grille assem-

bly and refit using the screws removed.

4. Electrical Connections

Fig.8 Cable entry position

4.1 Electrical connections

Fig.7 Grille Earth lead

With grille removed, connect the electrical supply

and controls wiring to the appropriate terminals (see

relevant wiring diagram section).

The unit has four holes for the cable entry, two on

the top and two on the side.

Cable entry may be

moved to alternative position if desired (see Fig.8

drawing).

An EARTH lead is connected to the lid from the unit

body, push on connection at grille. When replacing

the grille onto the unit ensure the EARTH lead is re-

connected. (see Fig.7 )

3. Installation Details

Fig.4 Fixing points

Fig.5 Wire fixing

Fig.6 Rod fixing

41001187 Iss 07

4.2 Electrical connections for standard models

Fig.12 Wiring of the heaters without using remote switch

4.3 Electrical connections without using the remote switch standard models

If the heaters are to be controlled by means other than the remote switch supplied, eg BMS, then

the heat output can be selected by connecting the appropriate terminals.

WIRED TERMINALS

RAC1306 RAC1309

2 +3 + 4 or 5

6000W 9000W

2 + 4 or 5

2000W 000W

3 + 4 or 5

4000W 6000W

Please note the ‘4’ or ‘5’ terminal must always be connected

4. Electrical Connections.

L2 L3

Fig.10 Three Phase connection Fig.11 Single Phase connection

Fig.9 Remote switch wiring

ON/OFF

BOOST

HEAT I.

HEAT II.

41001187 Iss 07

5.1 Models for wireless controls

The wireless controlled model RAC1 06RF can

be controlled by Claudgen wireless controllers

CZC1, CZC2 or CZC . The heater will not work

without a controller. Each controller has a unique

identification code, it can control an unlimited

number of heaters and will not interfere with other

controllers within the building. For more details

please follow the instructions supplied with the

controller.

5.2 Standard models

All standard RAC heaters

are supplied with a remote switch that gives the

following functions; On/off, fan, fan boost and

heat.

For thermostatic control, a room thermostat with

6A switch rating maybe connected to the circuit.

The thermostat should be wired between the ter-

minal 1 and the heater remote switch.

5. Operation.

4. Electrical Connections.

4.4 Electrical connections for wireless control models

To switch on the appliance and operate the blower,

depress the left-hand switch (marked “on/off”).

To change the fan speed use fan/boost switch.

When the heat 1 switch only (marked with a single

bar) is depressed the heat output is ⅓ of full heat.

RAC1 06 - 2kW,RAC1 09 - kW

When the heat 2 switch only (marked with a double

bar) is depressed the heat output is ⅔ of full heat.

RAC1 06 - 4kW,RAC1 09 - 6kW

When both heat switches are depressed the full heat

output is available.

RAC1 06 - 6kW,RAC1 09 - 9kW

Fig.15 CZC1 Fig.16 CZC3 Fig.17 CZC2

Fig.13 ‘L’ and ‘N’ connections Fig.14 Earth connection

41001187 Iss 07

ALWAYS ENSURE THAT THE MAIN EXTER-

NAL ELECTRICITY SUPPLY IS SWITCHED

OFF EFORE COMMENCING ANY MAINTE-

NANCE ON THIS HEATER.

To obtain the best results from the heater, it is es-

sential to avoid the accumulation of dust and dirt

within the unit on the air inlet and discharge grilles.

For this reason regular cleaning is necessary, pay-

ing particular attention to the removal of dirt build up

on the rotor blades.

Cleaning of the fan is best carried out with a soft

brush.

The product should be serviced annually.

Servicing shall be undertaken by a competent per-

son.

6.2 General

If the air curtain does not operate after switching on,

then a suitably competent service engineer should

be called to identify the nature of the fault.

All Air Curtains are fitted thermal cut-outs and motor

thermal protection.

Other faults in relation to the element, motor and

wiring should be identified using conventional fault

finding techniques.

In the event that electrical components are replaced,

please ensure that electrical safety checks in accor-

dance with the regulations in force in the country of

use are undertaken.

6.3 Thermal and fault protection

The units are protected from overheating in the

event of fan failure or an obstruction of the free air-

flow by thermal cut-outs.

6. Servicing & Maintenance

6.1 Maintenance

If this happens, the thermal cut-outs effectively

switch off the appliance by disconnecting power to

the control circuit. The appliance will not operate

until the thermal cut-outs are manually reset. This

should be done by a competent electrician.

The heaters are also protected by thermal fuses to

prevent catastrophic failure. The thermal fuse will

trip and disconnect power to the affected heater.

Thermal fuses are not resettable.

6.4 Fault Conditions

If the heater will not operate, disconnect it from the

mains and arrange for a certified electrician to at-

tend to investigate the reason.

6.5 Replacing Fan Heater Assembly

Remove the lid.

Disconnect the internal wiring from the main termi-

nal block. Remove the four nuts and washers fixing

the fan heater assembly to the back of the case.

The fan heater assembly can now be eased for-

ward and removed from the heater case. Fit re-

placement fan heater and reassemble in reverse

order.

6.6 Spares

It is essential when ordering spares or replacement

parts to state the model number and the serial

number on the rating place fixed to the top of the

unit.

In the interest of progress the Company reserve the

right to vary specifications from time to time without

notice. The material listed is offered subject to the

Company’s General Conditions of Sale, a copy of

which can be obtained on request.

Consort Equipment Products Ltd

Registered Office: Thornton Industrial Estate

Milford Haven, Pembrokeshire, S 73 2RT

Tel: 01646 692172 Fax: 01646 695195

BS EN ISO 9001 Registered Company No FM12671

41001187 Iss 07

Fig.18 Wiring diagram

standard models

41001187 Iss 07

Fig.19 Wiring diagram models for

wireless controls

Otros manuales para SCREENZONE RAC1306

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Calentador de Claudgen

Claudgen

Claudgen CA1309S Instrucciones de funcionamiento originales

Claudgen

Claudgen HE7402RF Manual

Claudgen

Claudgen CH06CS Manual

Claudgen

Claudgen HE7010RF Manual

Claudgen

Claudgen ScreenZone RAC0603 Manual de usuario

Claudgen

Claudgen ScreenZone CA1514S10 Manual de usuario

Claudgen

Claudgen HE6137SL Manual de uso y mantenimiento

Claudgen

Claudgen HE8320 Instrucciones de funcionamiento originales

Claudgen

Claudgen HE7237 Manual de usuario

Claudgen

Claudgen CA1509S Instrucciones de funcionamiento originales

Claudgen

Claudgen HE8515 Manual

Claudgen

Claudgen HE8326-33 Manual

Claudgen

Claudgen SCREENZONE RAC1306 Manual de usuario

Claudgen

Claudgen HE7433 Instrucciones de funcionamiento originales

Claudgen

Claudgen CH06CSi Manual de usuario

Claudgen

Claudgen RAC1509 Manual de usuario

Claudgen

Claudgen HE7010W-30 Manual

Claudgen

Claudgen HE7402 Instrucciones de funcionamiento originales

Claudgen

Claudgen RCT250 Manual

Claudgen

Claudgen RCT250SL Manual de uso y mantenimiento

Claudgen

Claudgen CH06CSiRX Manual de usuario

Claudgen

Claudgen ScreenZone RAC10HL Manual de usuario

Claudgen

Claudgen CA1309S Manual

Claudgen

Claudgen HE6351 Manual

Manuales populares de Calentador de otras marcas

oventrop

oventrop Regucor Series Manual de usuario

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manual de usuario

ELMEKO

ELMEKO ML 150 Manual de usuario

BN Thermic

BN Thermic 830T Manual de usuario

KING

KING K Series Guía

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guía de inicio rápido

Well Straler

Well Straler RC-16B Manual de usuario

EUROM

EUROM 333299 Manual de usuario

Heylo

Heylo K 170 Manual de usuario

Eterna

Eterna TR70W Manual de usuario

Clarke

Clarke GRH15 Manual de instrucciones

IRSAP

IRSAP The Radiator Company Ovali Manual de usuario

Empire Heating Systems

Empire Heating Systems WCC65 Manual de usuario

Wetekom

Wetekom 92 86 43 Manual de usuario

Desa

Desa SPC170-F Manual de usuario

Watlow

Watlow Watrod Electric Tubular Heaters Manual de usuario

Haverland

Haverland ECO-DRY GPS Series Manual de lista de piezas

Stelpro

Stelpro ASILVC2060 Series Manual de usuario