Classic Exhibits Perfect 10 Manual de usuario

www.classicexhibits.com

866.652.2100

WHEN DISASSEMBLING TIGHTEN ALL KNOBS TO PREVENT LOSS DURING SHIPPING

Order #XXXXX - P10 -

Page 1 of 5

Step 1

patent D599,121

VK-1513 Nina - General Layout

Plan View Perspective View

10’

www.classicexhibits.com

866.652.2100

WHEN DISASSEMBLING TIGHTEN ALL KNOBS TO PREVENT LOSS DURING SHIPPING

Order #XXXXX - P10 -

Page 1 of 5

Step 1

patent D599,121

Nina - Backwall Assembly

Item

Qty.

Steps:

NOTE: Assembly may be easiest if assembled face down on floor then lifted upright.

1) Connect upper curved vertical extrusions [3a,3] to leg assemblies [1,2].

2) Connect lower and upper horizontal extrusions between vertical assemblies by slightly

tightening BLACK knobs on backside of extrusion as shown.

NOTE: Make sure velcro faces toward back and knobs face horizontally as shown in detail.

** Various Accessories Available **

Description

Left Leg Assembly

Right Leg Assembly

Right Upper Curved Vertical

Left Upper Curved Vertical

83”w Horizontal w/ Hinge

Start Assembly of Backwall face

down on floor. Then lift upright.

Black

Knob

Horizontal

extrusion

Turn Knob Clockwise

to Tighten Lock

STAR indicates location of

knobs on BACKSIDE of unit.

Stopper

Hinge Extrusion

Vertical

Connection Bar

Vertical Connection Bar -

Slide Bar into lower leg

assembly, secure in place.

Slide upper vertical over

bar and secure into place.

Step stool may be required

for assembly.

NOTE: When assembling horizontals they should be

placed approximately one inch from TOP and BOTTOM.

Slide

horizontal into groove

Assure

that a good

connection is made

and tighten to secure.

www.classicexhibits.com

866.652.2100

WHEN DISASSEMBLING TIGHTEN ALL KNOBS TO PREVENT LOSS DURING SHIPPING

Order #XXXXX - P10 -

Page 2 of 5

Step 2

patent D599,121

Nina - Backwall Attachments

Light Connection

Attach lights to

backwall where

desired and

tighten in place.

When desired location

is found, tighten

set screw to secure.

Slide connector on back

of A10 clamp into groove

of extrusion.

Example of A10 Clamp Attachment

Tighten knob to

secure wing in

place.

A10’s

Accessary Attachment

Attach header support to backwall then

attach header to support with velcro.

Header

Cubby Attachment

Slide onto back pin first.

When attaching counter you will need to first

slide shelf onto back pin then set down on

front pin.

Pins

Thumbscrew

Shelf attaches to section

5 by setting atop pins

located on right side

and securing into place

with thumbscrew on left.

www.classicexhibits.com

866.652.2100

WHEN DISASSEMBLING TIGHTEN ALL KNOBS TO PREVENT LOSS DURING SHIPPING

Order #XXXXX - P10 -

Page 3 of 5

Step 3

patent D599,121

Workstation Assembly

Part Number

Steps:

1) Connect lower horizontal extrusion [C] between bottom of leg assemblies [A and B] as shown.

2) Insert Laminated infill into grooves of leg assemblies [A and B].

3) Attach extrusion door between leg assemblies [A and B] and on top of laminated infill.

4) Attach upper horizontal extrusion w/ door stopper [D] between leg assemblies [A and B],

and set flush with top of legs [A and B].

Description

Left Leg Assembly

Right Leg Assembly

Horizontal Extrusion

Horiontal Extrusion w/ Door Stopper

Black

Knob

Turn Knob Clockwise

to Tighten Lock

DOOR

Laminated Infill

A (left)

B (right)

D (w/ Door Stopper)

Knobs face INSIDE

of workstation

Knobs face INSIDE

of workstation

Knobs face FORWARD

Pins are

located on INSIDE

FRONT vertical

of Leg

Assemblies

NOTE: Make sure the lock is flush with extrusion before tightening. If lock will not fully

engage, gently rock lock and extrusion back and forth while turning knob until lock

fully opens.

Align with bottom of leg assemblies [A and B].

www.classicexhibits.com

866.652.2100

WHEN DISASSEMBLING TIGHTEN ALL KNOBS TO PREVENT LOSS DURING SHIPPING

Order #XXXXX - P10 -

Page 4 of 5

Step 4

patent D599,121

Workstation Assembly (Cont’d)

Part Number

Steps:

1) Attach horizontal extrusion [E] between vertical leg assemblies [A and B] as shown below.

2) Insert Laminated infill into grooves of vertical leg assemblies [A and B].

3) Attach upper horizontal extrusion [F] between vertical leg assemblies [A and B] atop infill.

Place internal shelf into assembled pedestal atop pins.

5) Set Counter atop assembled pedestal and secure with Velcro straps attached to underside of top.

Description

Horizontal Extrusion

Laminated

Infill

Knobs facing FORWARD

Place internal shelf into

workstation then

place counter atop

assembled workstation.

Internal

Shelf

Knobs face INSIDE

of workstation

www.classicexhibits.com

866.652.2100

WHEN DISASSEMBLING TIGHTEN ALL KNOBS TO PREVENT LOSS DURING SHIPPING

Order #XXXXX - P10 -

Page 5 of 5

Step 5

patent D599,121

Workstation Assembly (Cont’d)

When assembled

Part Number

Steps:

Slide connection bar into lower leg assembly. Slide upper vertical over bar and secure both.

2) Attach monitor mount to vertical as shown in detail below.

Description

Curved Montior Mount Extrusion

Hex Key Tool

V20

Adjust V20 connector to

desired location.

Then remove screws.

Place mount plate

in front of V20 connectors.

Then secure with screws.

NOTE: Monitor mount should be installed

while laying down on floor

Monitor Mount Attachment

Vertical Connection Bar -

Slide connection bar into

lower leg assembly. Slide

upper vertical over bar and

secure both as shown.

www.classicexhibits.com

866.652.2100

WHEN DISASSEMBLING TIGHTEN ALL KNOBS TO PREVENT LOSS DURING SHIPPING

Order #XXXXX - P10 -

patent D599,121

Case Packing - Case 1 of 3

Wings

Wing Attachment

Level 2 Level 3 Level 4

Leg Assembly

Horizontal Extrusions 4 & 5

Extrusions 3 & 3a

Level 1

Top View

Additional Items:

- Setup Hardware

- Graphic

- (3) Lights

Connection Bar

Round Sign

www.classicexhibits.com

866.652.2100

WHEN DISASSEMBLING TIGHTEN ALL KNOBS TO PREVENT LOSS DURING SHIPPING

Order #XXXXX - P10 -

patent D599,121

Case Packing - Case 2 of 3

Top View

Level 1

Backside

Shelf

Cubby

www.classicexhibits.com

866.652.2100

WHEN DISASSEMBLING TIGHTEN ALL KNOBS TO PREVENT LOSS DURING SHIPPING

Order #XXXXX - P10 -

patent D599,121

Case Packing - Case 3 of 3

Level 1 Level 3

Top View of Each Level

Counter

Internal

Shelf

Level 2

Inserts

Door

Level 4

Leg Assembly

Horiz. Extrusion F

Horiz. Extrusion D

Level 5

Leg Assembly

Horiz. Extrusion E

Horiz. Extrusion C

Connection Bar for Verticals

Monitor

Mount

Otros manuales para Perfect 10

Otros manuales de Monitor de Classic Exhibits

Classic Exhibits

Classic Exhibits Symphony SYK-1036 Manual

Classic Exhibits

Classic Exhibits Perfect 10 VK-1510 Kira Manual de usuario

Classic Exhibits

Classic Exhibits Symphony SYK-1040 Manual

Classic Exhibits

Classic Exhibits visionary DESIGNS VK-1321 Manual de usuario

Classic Exhibits

Classic Exhibits Supernova VK-1968 Manual

Classic Exhibits

Classic Exhibits Symphony SYK-2014 Manual

Classic Exhibits

Classic Exhibits Perfect 10 VK-1402 Manual de usuario

Classic Exhibits

Classic Exhibits Symphony SYK-1001 Manual

Classic Exhibits

Classic Exhibits SYMPHONY SYK-1021 Manual

Classic Exhibits

Classic Exhibits Symphony SYK-1038 Manual de usuario

Classic Exhibits

Classic Exhibits visionary DESIGNS TF-513 Manual

Classic Exhibits

Classic Exhibits Symphony SYK-2019 Manual

Classic Exhibits

Classic Exhibits SEGUE DESIGNS VK-1302 Manual

Classic Exhibits

Classic Exhibits Symphony SYK-2011 Manual

Manuales populares de Monitor de otras marcas

Linear Acoustic

Linear Acoustic LQ-1000 Manual de usuario

AOC

AOC I2579V Manual de usuario

Gateway

Gateway FPD1520 Manual de usuario

Furuno

Furuno Mu 120c Manual de usuario

Asus

Asus VB171D - 17" LCD Monitor Manual de usuario

Dell

Dell S2230MX Instrucciones de uso

Philips

Philips 107C64 Manual de usuario

Dell

Dell S2409WFP Manual de usuario

EverFocus

EverFocus EN-7517E Manual de usuario

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manual de usuario

Dell

Dell Precision 7680 Manual de instrucciones

LG 50PM1M - - 50" Plasma Panel Manual de usuario

Bosch

Bosch DDU 9 Manual de usuario

Acer

Acer A231HL Manual de usuario

Philips

Philips 86BDL4152T Manual de usuario

NEC

NEC AccuSync LCD5V Manual de usuario

Emay

Emay SleepO2 Manual de usuario

IBM

IBM 6360 Instrucciones de instalación