Classe Audio CAV-150 Manual de usuario

CLASSÉ AUDIO

CAV-150

MULTI-CHANNEL

POWER AMPLIFIER

CAV-150

OWNER'S MANUAL

CLASSÉ DESIGN PHILOSOPHY

1. REPEATED LISTENING DESIGN SESSIONS:

Fine tuning of sound by exchanging and mixing of parts (transistors, capacitors, wiring,

PCB boards etc.), and adjusting many specific operating voltages within proper engineering

ranges, producing an overall sonic recipe giving the most natural harmonic realism of music

typical of instruments in a live performance.

2. UPGRADABLE SINGLE CIRCUIT DESIGNS:

All Classé products (all preamps and all amps) share exactly the same circuit (excluding

moving coil and moving magnet phono circuits). This means all amplifiers and all high level

circuits of the preamps are the same. The same circuit is tailored to different power levels etc.

Differences between less expensive models and more expensive models are parts quality and

compliment, power supply extravagance and the amount of filtering etc., as well as features and

packaging.

This means that for years Classé has been constantly fine tuning and upgrading this

circuit and its application, thus reaching a very high level of understanding and musical

achievement which benefits all models - least expensive, most expensive, preamps and

amplifiers alike.

3. EXTREME LONG LIFE IN REAL WORLD CONDITIONS:

Choosing the best attainable quality parts and materials combined with the advantages of

the two above-mentioned areas provides Classé owners with years of proven trouble free

reliability and musical enjoyment.

-3-

CAV-150

OWNER'S MANUAL

TABLE OF CONTENTS

UNPACKING & SET-UP............................................................ 4

GENERAL CONNECTIONS AND OPERATIONS ................. 5

CONNECTIONS AND DIAGRAMS .......................................... 8

WARRANTY .............................................................................. 11

SPECIFICATIONS ..................................................................... 13

WARRANTY REGISTRATION ................................................ 14

-4-

UNPACKING & SET-UP

Your Classé CAV-150 multi-channel power amplifier is packed in high density, semi-rigid

foam placed in a special cardboard box. To remove the unit, open and spread all the top flaps of the

box and by its sides, lift out the entire unit and put it on a large flat surface. Take it out of the plastic

bag and inspect the unit for any concealed damage. Apart from this owner's manual, please ensure

the following have also been included:

1) Detachable linecord.

2) Allen key for top plate.

Please report any damage or missing parts to your dealer as soon as possible.

Place the CAV-150 at or near its final set-up position, allowing 8 inches at the rear for

tightening the speaker output connectors. For optimum sonic performance, we recommend the

optional CLASSÉ REFERENCE A.C. LINECORD. Consult your dealer regarding this accessory.

The power transformer in the CAV-150 is located at the front-center of the unit. Ideally, a

few feet should separate this area from components which potentially could pick up hum. These

include preamplifiers, turntables, and interconnect cables. In terms of providing adequate airspace

for cooling, a good rule of thumb is to allow 6 inches above and 3 inches on each side of the unit.

Check the Serial Number sticker on the back of the unit for the correct operating voltage.

The CAV-150 has one line fuse (internal), the rating of which should be as follows:

LINE VOLTAGE FUSE RATING

100 or 120 V.A.C. 8 AMP SLOW BLOW 125 or 250 volts

220 or 240 V.A.C. 6 AMP SLOW BLOW 250 volts

INTERNAL RAIL FUSES:

The CAV-150 is designed with each channel protected by one pair of internal fuses for

positive and negative rails (see fig-1b page 8) 8 AMP FAST BLOW 125 volts

-5-

GENERAL CONNECTIONS AND OPERATION:

A.C. LINE: Insert the linecord into the A.C. receptacle on the rear of the unit.

CAUTION: SAFETY INSTRUCTIONS

DISCONNECT AC LINE CABLE WHILE MAKING ALL CONNECTIONS. "FLOATING THE

GROUND", OR DEFEATING THE GROUND ON A 3-PRONG LINECORD MAY CREATE

A SHOCK HAZARD. CONNECT ALL INTERCONNECT CABLES BETWEEN THE

ELECTRONICS BEFORE CONNECTING THE A.C. LINECORDS TO THE WALL

OUTLETS. THIS WILL REDUCE THE POTENTIAL SHOCK HAZARD. SEE ALSO THE

WARRANTY SECTION OF THIS OWNER'S MANUAL.

REGULAR INPUTS:

The CAV-150 is factory set for REGULAR use. Connect the regular interconnect to the

RCA input jacks, for Channel-1 and Channel-2 make sure the Regular/Balanced switch is set to

position marked "Regular" (down) which selects REGULAR inputs for both channels-1 and

channel-2. (The Balanced XLR input jacks are automatically disable).

BALANCED INPUTS:

Balanced inputs are available to Channel-1 and Channel-2 only. For use with balanced

preamplifier other than Classé, the wiring of the 3-pin XLR connectors must be matched to that of

the Classé wiring configuration, which are as follows:

PIN 1: Ground

PIN 2: Positive (non-inverting) signal

PIN 3: Negative (inverting) signal

If the pin configuration of the preamplifier differs from above, the balanced interconnects

must be modified to accommodate the different preamp. Make sure the Regular/Balanced switch is

-6-

set to position marked "Balanced" (up). Regardless of the type of input used, NORMAL or

BRIDGED operation is still possible for Channel-1 and Channel-2

NORMAL OPERATION:

Input and output connectors for each channel are clearly grouped and marked on the back of

the amplifier. (Units are preset at the factory for NORMAL.)(see fig.2&3 page 9&10) for typical

connections of the CAV-150.

Use only high quality interconnect and loudspeaker cables, and make all connections tight. If

the input plugs are loose, remove them and pinch down the ground leaves slightly with pliers.

Observe correct phasing of the loudspeaker connections, and tighten.

BRIDGED OPERATION:

The six (6) channels of the CAV-150 are divided into three (3) groups. These groups can be

operated and configured independently _ Channel-1 with Channel-2, Channel-3 with Channel-4, and

Channel-5 with Channel-6. When in bridged mode, the inputs of CH-1, CH-3 and CH-5 are used

respectively. The unused inputs of CH-2, CH-4 and CH-6 are automatically disconnected when

configured in bridged mode. The following steps should be performed to switch between

NORMAL mode and BRIDGED mode.

1) Turn OFF the unit and disconnect the AC cable.

2) Reconnect all cables. Make sure the input and output connections of channels to be

switched are according to the operating mode. (see fig.2&3 page 9&10).

3) Locate and set the mode switch to the desired operating mode (see fig.1a page 8) for

channels to be switched (up=BRIDGED, down=NORMAL)

Please read through the previous normal section for general notes on securing good connections, and

safety tips.

-7-

CAUTION: Please remember that the negative output connection of a bridged amplifier is NOT a

ground. Do not use a "common ground" or switchbox set-up. Do not use with electronic crossovers

which have a common ground.

REMOTE CONTROL: (optional)

With a simple connection from the receiver box to the remote jack at the back of the

amplifier, (see Fig.1a page 8) the power amplifier can be turned ON/OFF from a distance (or from

another room).

SPECIAL FEATURES: The front LED will change from Red to Green if any of the (12) internal

rail fuses are blown.

-8- CL

-9-

-10-

Tabla de contenidos

Otros manuales de Amplificador de Classe Audio

Classe Audio

Classe Audio CA-3200 Manual de usuario

Classe Audio

Classe Audio CA-2300 Manual de usuario

Classe Audio

Classe Audio CA-5200 Manual de usuario

Classe Audio

Classe Audio CAM-200 Manual de usuario

Classe Audio

Classe Audio DR-10 Manual de usuario

Classe Audio

Classe Audio CA-150 Manual de usuario

Classe Audio

Classe Audio CAP-80 Manual de usuario

Classe Audio

Classe Audio CAP-101 Manual de usuario

Classe Audio

Classe Audio CP-40 Manual de usuario

Classe Audio

Classe Audio CP-500 - V2.8 Manual de usuario

Classe Audio

Classe Audio C-151 Manual de usuario

Classe Audio

Classe Audio OMICRON Manual de usuario

Classe Audio

Classe Audio CA-2300 Manual de usuario

Classe Audio

Classe Audio CA-M300 - V1.4 Manual de usuario

Classe Audio

Classe Audio SSP-60 Manual de usuario

Classe Audio

Classe Audio Sigma SSP Manual de usuario

Classe Audio

Classe Audio CT-M300 - V1.2 Manual de usuario

Classe Audio

Classe Audio DR-9 Manual de usuario

Classe Audio

Classe Audio CA-M400 Manual de usuario

Classe Audio

Classe Audio CT-M600 - V1.6 Manual de usuario

Classe Audio

Classe Audio CA-201 Manual de usuario

Classe Audio

Classe Audio OMEGA-PREMKIII Manual de usuario

Classe Audio

Classe Audio CP-47.5 Manual de usuario

Classe Audio

Classe Audio DR-3 Manual de usuario

Manuales populares de Amplificador de otras marcas

ASTRO

ASTRO HVO V40 P Manual de usuario

Marantz

Marantz SUPERSCOPE BLA-545 Instrucciones de montaje

NAD

NAD CI980 Manual de usuario

Technics

Technics SE-CH770 Manual de usuario

Harman Kardon

Harman Kardon HK6300 Manual de usuario

NAD

NAD T975 Manual de usuario

McIntosh

McIntosh MA6850 Manual de usuario

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manual de usuario

Viatron

Viatron Autrix Manual de usuario

GME

GME GA9800 Manual de usuario

Atlas

Atlas CP700 Manual de usuario

Roland

Roland KC-1000 Manual de usuario

Pyle

Pyle PFMRA350BW Manual de usuario

Advantage

Advantage S-250 Manual de usuario

IRT Electronics

IRT Electronics DVA-3007 Manual de usuario

Dimavery

Dimavery BA-100 Series Manual de usuario

Sony

Sony XM-S400D Manual de usuario

Schertler

Schertler ROY X Manual de usuario