Classe Audio C-501 Manual de usuario

CLASSÉ AUDIO

C-501

REMOTE CONTROL

BALANCED PREAMPLIFIER

C-501

OWNER'S MANUAL

CLASSÉ DESIGN PHILOSOPHY

1. REPEATED LISTENING DESIGN SESSIONS:

Fine tuning of sound by exchanging and mixing of parts (transistors, capacitors, wiring, PCB boards

etc.), and adjusting many specific operating voltages within proper engineering ranges, producing an

overall sonic recipe giving the most natural harmonic realism of music typical of instruments in a

live performance.

2. UPGRADABLE SINGLE CIRCUIT DESIGNS:

All Classé products (all preamps and all amps) share exactly the same circuit design philosophy

(excluding moving coil and moving magnet phono circuits). This means all amplifiers and all high

level circuits of the preamps benefit from the same design goals. Similar circuits are then tailored to

different power levels etc. Differences between less expensive models and more expensive models

are parts quality and compliment, power supply extravagance and the amount of filtering etc., as

well as features and packaging.

This means that for years Classé has been constantly sonically fine tuning and technically upgrading

this circuit design and its application, thus reaching a very high level of natural musical enjoyment,

as well as excellent reliability which benefits all models - least expensive, most expensive, preamps

and amplifiers alike.

3. EXTREME LONG LIFE IN REAL WORLD CONDITIONS:

Choosing the best attainable quality parts and materials combined with the advantages of the two

above-mentioned areas provides Classé owners with years of proven trouble free reliability and

musical enjoyment.

-3-

C-501

OWNER'S MANUAL

TABLE OF CONTENTS

UNPACKING & SET-UP..................................................... 4

A.C. LINE POWER............................................................... 5

INPUTS.................................................................................. 6

OUTPUTS ............................................................................. 8

FRONT PANEL CONTROLS............................................... 9

FEATURES AND SPECIFICATIONS ................................. 18

-4-

NPACKING & SET-UP

Your new preamplifier has been carefully wrapped in heavy gauge plastic, packed in semi-

rigid foam and contained in a special box. To remove the unit, open and spread the top flaps of the

box. By its sides, lift out the entire unit with the foam pieces intact. Remove each foam side by

pulling straight out. Remove the plastic wrap and inspect the unit for any concealed damage. Apart

from this owner's manual, please ensure the following has also been included:

1) Detachable A.C. linecord.

2) 5/64 in. Allen key for top cover

3) Remote Control unit (Allen key and Batteries AAA X 2 included).

Please report any damage or missing parts to your dealer promptly.

This preamplifier, being capable of very high gain, must be located in a position free of any

hum-inducing magnetic fields. (This also applies to turntables and interconnect cables.) Positions

adjacent to power amplifiers, A.C. line filters, or regulation devices should be avoided. Ideally, a

few feet should separate the preamplifier from the power amplifier. As well, keep low-level

interconnect cables away from the power amp and separate from A.C. linecords.

Heat generated by the preamplifier is negligible. Air space around the unit need not be a

concern.

Check the Serial Number sticker on the back of the unit for the correct operating voltage.

Regardless of voltage, the fuse rating should be 2 AMP SLO-BLO.

-5-

.C. LINE POWER

The preamplifier has no power switch. Its low power consumption and improved sonics

from always being ON led to the omission of an ON/OFF switch. In fact, while thoroughly musical

shortly after turn-on, the preamplifier will exhibit "sonic growth" for the first 300 hours of used.

For optimum sonic performance, you should consider use of the optional CLASSE

REFERENCE A.C. LINECORD. Consult your dealer regarding this accessory.

SAFETY FEATURE: The preamplifier is designed with an Auto-Muting Circuit which

engages and is indicated by two FLASHING RED ARROWS when the unit is first connected, or

after an A.C. power failure. After 45 seconds of stabilizing the preamplifier is automatically

switched to "MUTE" mode, after which all operating functions such as input etc. may then be

selected.

CAUTION: "FLOATING THE GROUND” OR DEFEATING THE GROUND ON A 3-

PRONG LINECORD MAY CREATE A SHOCK HAZARD. CONNECT ALL INTERCONNECT

CABLES BETWEEN THE ELECTRONICS BEFORE CONNECTING THE A.C. LINECORDS

TO THE WALL OUTLETS. THIS WILL REDUCE THE POTENTIAL SHOCK HAZARD. SEE

ALSO THE WARRANTY SECTION OF THIS OWNER'S MANUAL.

-6-

NPUTS

The input jacks are clearly marked on the back of the C-501. The following inputs are

provided: BAL 1, BAL 2, REG 1 (also used for Phono), REG 2, REG 3, REG 4, TAPE, and a

SURROUND sound loop. (see figure 3).

OPTIONAL INTERNAL PHONO FEATURE:

The REG 1 input jacks are to be used with the optional phono feature (see fig.6) The phono

ground screw is located between the REG 4 and TAPE IN jacks. The optional phono can

accommodate both magnetic and moving coil cartridges of various outputs. In the MC position, gain

of the Moving Coil stage is factory preset at 16dB which matches perfectly with most typical MC

cartridges. With the resistor kit included with the optional phono feature, the gain can also be

adjusted to 20db, 25db, or 30db in order to optimize system gain, and lower noise while using other

less typical MC cartridges. (Note: The MC gain is in addition to the standard MM gain of 42dB). To

change the MC gain, proceed as follows:

1. Disconnect A.C. linecord from the wall outlet.

2. Remove top cover with Allen key supplied.

3. Locate R245 and R145 (see fig.6), which are the MC gain setting resistors for the LEFT

and RIGHT channel respectively. Remove the resistors and replace them with newly selected ones,

according to the following chart.

GAIN COLOR CODED RESISTOR (or) NUMERICAL RESISTOR

Standard: 16db (Brown, Brown, Black, Black) 1100 (110 ohms)

20db (Red, Black, Black, Black) 2000 (200 ohms)

25db (Orange, Grey, Orange, Black) 3830 (383 ohms)

30db (Violet, Blue, Grey, Black) 7680 (768 ohms)

4. Having completed the resistor changes, replace the top cover.

-7-

BALANCED, TAPE, AND REGULAR INPUTS

The BALANCED INPUTS are true differential high level inputs, wired as follows:

PIN 1: GROUND

PIN 2: POSITIVE (NON-INVERTED) SIGNAL

PIN 3: NEGATIVE (INVERTED) SIGNAL

The Balanced inputs may be used with CD players that have a balance output, or any other

high level, balanced source.

The TAPE IN of the C-501 should be connected to the LINE OUT or TAPE OUT of the tape

deck. (See FRONT PANEL CONTROLS: TAPE SWITCH.)

The Regular inputs may be used with any high level sources (REG 1 may also be used with

the optional Classé Internal Phono Feature.)

-8-

UTPUTS

The C-501 has both regular (single-ended) and balanced outputs. Both are working at all

times, and may be used separately, or simultaneously.

TAPE OUTPUT

Whichever input is selected will be fed to the TAPE OUTPUT jacks. This should be

connected to the TAPE IN or LINE IN of the tape deck.

REGULAR OUTPUTS

Simply connect your regular interconnects to the RCA output jacks marked REGULAR OUT

on the back of the C-501.

BALANCED OUTPUTS

A balanced power amplifier and balanced interconnects are also required. For use with

balanced power amplifiers other than Classé, the wiring of the 3-pin XLR connectors must be wired

as follows:

PIN 1: GROUND

PIN 2: POSITIVE (NON-INVERTED) SIGNAL

PIN 3: NEGATIVE (INVERTED) SIGNAL

If the pin configuration of the power amplifier differs from above, the balanced interconnects

must be modified to accommodate the different power amp.

Having confirmed the correct connections, plug the XLR connectors of the balanced

interconnects into the locking XLR connectors on the rear panel of the C-501 marked BALANCED

OUT. (To remove the connectors, press the tab above the connector.)

-9-

RONT PANEL CONTROLS

NOTE: All functions (except Display, Gain, and Phase) may be activated directly on the front panel,

or otherwise by the hand held remote control.

DISPLAY:

Three (3) different display brightness levels can be selected (Full/Medium/Low as well as Off).

NOTE: With display set at the OFF position, activating any switches on the front panel or from the

remote control unit will temporarily turn the display to ON at full brightness. The display will

automatically turn back to OFF after approximately 10 seconds from the last change.

GAIN:

The dual gain feature provides the user to set the preamplifier either at REGULAR gain of

18db or LOW gain of 12db. The red indicator "GAIN" appears in the display when LOW gain is

selected.

PHASE:

Phase of the output signal can be switched between inverted (180 degrees phase shift) or

normal non-inverted (0 degree phase shift). The red indicator "PHASE" is shown when the unit is in

the inverted mode.

TAPE

The TAPE button selects the input signal, between the TAPE and SOURCE inputs, which

goes to the main REGULAR and BALANCED output jacks. The red indicator "TAPE" appears

when Tape input is selected. However, the SOURCE signal always appears at the TAPE OUT jacks

and shown in the display.

-10-

SURROUND

When the surround mode is engaged, the selected signal is directed to the SURROUND

output connectors where it is sent to a Surround Sound Processor for the decoding process. The

Front-Left and Front-Right output signals from the Surround sound processor are then fed to the Left

and Right Surround input connectors on the back of the preamplifier. The main outputs of the

preamplifier (both Balanced or Regular) are now to be connected to the amplifier powering the

Front-left and Front-right speakers of your surround sound system. (see figure 4)

All preamplifier functions (except input select, display, and mute) are disabled in the

surround mode.

SAFETY FEATURE: The volume control of the preamplifier is automatically brought back to the

MIN position, and MUTE is also engaged when the preamplifier is switched back from the surround

mode to the regular stereo mode.

VOLUME CONTROL

The preamplifier volume control has a total of 60 steps of level adjustments which varies the

level of both channels simultaneously. The volume can be operated from the remote using the hand

held control unit or manually turning the control knob at the preamplifier.

The volume will turn up or down ONE step at a time when the buttons are pressed

intermittently. When the buttons are pressed and held constantly the volume will change rapidly

until the pressed volume button is released.

Tabla de contenidos

Otros manuales de Amplificador de Classe Audio

Classe Audio

Classe Audio SSP-30 MKII Manual de usuario

Classe Audio

Classe Audio CP-35 Manual de usuario

Classe Audio

Classe Audio CA-5100 Manual de usuario

Classe Audio

Classe Audio CA-201 Manual de usuario

Classe Audio

Classe Audio CA-M600 Manual de usuario

Classe Audio

Classe Audio CA-101 Manual de usuario

Classe Audio

Classe Audio CAP-101 Manual de usuario

Classe Audio

Classe Audio CA-5300 - V1.4 Manual de usuario

Classe Audio

Classe Audio CAV-180 Manual de usuario

Classe Audio

Classe Audio CA-M600 Manual de usuario

Classe Audio

Classe Audio CA-5200 Manual de usuario

Classe Audio

Classe Audio CA-5100 Manual de usuario

Classe Audio

Classe Audio Omega Series Manual de usuario

Classe Audio

Classe Audio CP-800 Manual de usuario

Classe Audio

Classe Audio CP-40 Manual de usuario

Classe Audio

Classe Audio CA-150 Manual de usuario

Classe Audio

Classe Audio CA-2200 Manual de usuario

Classe Audio

Classe Audio CA-2300 Manual de usuario

Classe Audio

Classe Audio CA-2100 - 3 Manual de usuario

Classe Audio

Classe Audio OMICRON Manual de usuario

Classe Audio

Classe Audio CP-500 Manual de usuario

Classe Audio

Classe Audio CAP-2100 Manual de usuario

Classe Audio

Classe Audio CT-2300 - V1.1 Manual de usuario

Classe Audio

Classe Audio C-303 Manual de usuario

Manuales populares de Amplificador de otras marcas

ASTRO

ASTRO HVO V40 P Manual de usuario

Marantz

Marantz SUPERSCOPE BLA-545 Instrucciones de montaje

NAD

NAD CI980 Manual de usuario

Technics

Technics SE-CH770 Manual de usuario

Harman Kardon

Harman Kardon HK6300 Manual de usuario

NAD

NAD T975 Manual de usuario

McIntosh

McIntosh MA6850 Manual de usuario

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manual de usuario

Viatron

Viatron Autrix Manual de usuario

GME

GME GA9800 Manual de usuario

Atlas

Atlas CP700 Manual de usuario

Roland

Roland KC-1000 Manual de usuario

Pyle

Pyle PFMRA350BW Manual de usuario

Advantage

Advantage S-250 Manual de usuario

IRT Electronics

IRT Electronics DVA-3007 Manual de usuario

Dimavery

Dimavery BA-100 Series Manual de usuario

Sony

Sony XM-S400D Manual de usuario

Schertler

Schertler ROY X Manual de usuario