Clas Ohlson CSH-500 Manual de usuario
Art. no: 18-8009/38-1786
Model: CSH-500
Network Switch
SUOMINORSKSVENSKAENGLISH
ENGLISH
Please read the entire instruction manual before
using and save for future use. We apologise for
any text or photo errors and any changes of
technical data.
Unpacking
Contents:
• 1 x 5 ports N-Way Switch
• 1 x AC/DC adaptor
• Instruction manual
Network Switch
Art. no: 18-8009/38-1786 Model: CSH-500
ENGLISH
5
Description
Model
Model no. CSH-500
Number of ports 5 TP ports
Port type 100BASE-TX/10BASE-T
Features
• 5 independent bandwidths with 10 Mbps to
100 Mbps capacity (Full Duplex).
• 5 ports with automatic speed selection
(Autonegotiation).
• 128 KB buffer memory.
• 1 K MAC address list.
• Full speed storage and forwarding technique
removes all broken packets.
• Max. ltering/forwarding speed: 18.800
packet/s per port.
• Support for IEEE 802.x transfer rate for Full
Duplex use.
• Back pressure for half duplex use.
• Compatible with IEEE 802.u and 802.-
standards.
• Plug-and-play with easy to read LEDs.
• 5 ports with auto MDIX which recognizes and
corrects cross cables.
LED´s
The switch has 6 x green LEDs. One indicates
on/off. The other 5 represent their respective ports
and shine constantly when connected to another
device. They ash when data is transferred through
the port.
5
ENGLISH
a b
Back panel
a) Connecting to the power point.
b) Ports 1-5
AC/DC adaptor
Use only the included AC/DC adaptor.
Ports
10/100 Mbps TP-ports. Every port has automatic
rate selection (autonegotiation) which recognizes
the connected port’s maximum bandwidth and
automatically sets the connected port to 10 Mbps
or 100 Mbps in full duplex, and 10 Mbps or 100
mbps in half duplex.
Connections
Every TP port uses a RJ-5 connection and has
an Auto MDIX function.
Cables
10 Mbps
Category , or 5 TP cable can be used to transfer
data at 10 Mbps or 20 Mbps (Full-Duplex) in a 10
BASE T network.
100 Mbps
Only category 5 TP cables can be used for data
transfer at 100 Mbps or 200 Mbps (Full-Duplex) in
a 100 BASE TX network.
Note: Category 5 TP cables are recommended
when installing new cables.
6
ENGLISH
Installation
The switch is Plug and Play compatible, which
means it needs no drive routines. The switch can
be used immediately after the cables are connected
and the power is turned on.
Location
• Place the switch on a clean at surface close
by a power point.
• Connect the adaptor to the switch and then
to the wall socket.
NOTE: Use only the included AC/DC adaptor for
the switch.
Configuration
Half and Full Duplex
This 5 ports N-Way switch supports both half and
full duplex. 10 BASE T and 100 BASE TX.
Half duplex: Data cannot be sent and received
simultaneously.
Full duplex: Data cannot be sent and received
simultaneously.
NOTE:
• Full duplex data transfer is only possible
between 2 devices with a dedicated link, e.g.
switch-switch or switch-PC.
• Both devices must have the capacity for full
duplex.
• Both devices must be capable of full duplex
(via autonegotiation).
Every port on this switch recognizes and sets the
data transfer rate through automatic rate control
(autonegotiation).
6
ENGLISH
Fast Ethernet
100 BASE-TX is a.ka. Fast Ethernet. With Fast
Ethernet data is sent 10 times as fast as with
traditional Ethernet (10 Mbps).
10 BASE T ports should have category , or 5
TP cables, and 100 BASE TX ports should have
category 5 TP cables.
If your 10 BASE T network uses category 5 TP
cables you can upgrade your network to a 100
BASE TX network by changing adaptors, hubs, etc.
Automatic rate selection
(N-Way Auto-Negotiation)
Every TP port has a built-in function for automatic
rate selection. This technique automatically sets
the broadest bandwidth immediately when the
connection is made with another device (usually
when the power is turned on or when resetting). The
function for automatic rate selection recognizes the
settings and rates of the different devices. Every port
has an Auto MDIX function which recognizes the
connected cable’s polarity and automatically adjusts
the switch to the correct polarity. The user only
needs to connect the device to an available 10/100
Mbps port.
MAC address list
Every data packet in the Ethernet contains both an
originating address and a destination address. This
6 byte ID is called the MAC address (Media Access
Control) address.
The switch can automatically store up to 1 K of
MAC addresses. They are deleted once the switch
is turned off or reset.
We recommend that the power be turned off
rst before conguring the network. When all
connections have been moved, turn on the power
again in order to recreate the internal MAC address
list.
8
ENGLISH
a
bc
d e
Example network
This switch can be used for SOHO in a company
network. Below is a simple 10/100 Mbps SOHO
network with maximum network rate and efciency.
10/100 Mbps switched network med 5 x separate
bandwidths.
a) Mail server with Gigabit Ethernet adaptor
b) 5-port 100/10 Mbps
c) 5-port 100/10 Mbps
d) Workstation with 10/100 Mbps
Fast Ethernet adaptors
e) Workstation with 10/100 Mbps
Fast Ethernet adaptors
8
ENGLISH
Troubleshooting
Most problems with the network are usually caused
by faulty cable connections. Check your cable
connections accordingly:
• Make sure the port´s LED is on. A lighted LED
means a correct connection. If the LED does
not light, check that the other end of the cable
is connected to a device which is connected
and has the power turned on.
• If the TP port´s LED lights up normally when
connected but data transfer is irregular:
a) Make sure that the connected device
is not set or forced at 100 Mbps, or 10
Mbps Full-Duplex.
b) Some devices use a physical or
software based switch to change
duplex settings. It is possible that the
function for automatic rate selection
does not recognize this type of duplex
setting.
c) Turn off the switch´s power and turn
it on again to reset the switch.
• Make sure the adaptor´s LED is lit.
• Try to send a message (transfer data) through
the switch. During data transfer, make sure the
light ashes at the port used.
• Send a message to the network server through
the switch. Make sure that the server’s TX/RX
LED ashes.
100 BASE TX set high standards for the cables
used. These standards are given in this instruction
manual. Some simple rules are:
• No cable should be over 100 m long.
• The cable length per segment is measured
from the switch.
11
11
Disposal
Follow local ordinances when disposing of this
product. If you are unsure about how to dispose of
this product contact your municipality.
Specifications
Model: 5 port 10/100 Mbps N-way
switch
Standards: IEEE 802.u: 100 BASE TX
IEEE 802.: 10 BASE T
Ports: 5 x 100 BASE TX/10
BASE T
Media support: 100 BASE TX category
5 TP 10 BASE T category
, or 5 TP
Bandwidth: 100 BASE TX/10 BASE
T 100/10 Mbps, via
automatic rate selection
Forwarding: 18 800 packet/s per port
@ max. 100 Mbps ltering
rate 1,800 packet/s per
port @ max. 10 Mbps
MAC addresses: Max. 1 K of addresses,
self-xing
Buffer memory: 128 KB
Duplex: All ports support half duplex
and full duplex
Auto MDIX: All ports support auto MDIX
which recognizes and
corrects cross cables
LEDs: 1 x for AC/DC adaptor,
1 x port for connection and
transfer activity.
AC/DC adaptor: Output V DC, 1 A
Power Consumption: Max. 2.5 W
Area of use
Operating Temperature: 0 °C to 5 °C
Storage temperature: -20 °C to 0 °C
Humidity: 10% to 0%
Certications: FCC class B and CE certied
Dimensions (w x d x h): 118 x 0 x 25 mm.
Tabla de contenidos
Idiomas:
Otros manuales de Cambiar de Clas Ohlson
Clas Ohlson
Clas Ohlson 36-2824 Manual de usuario
Clas Ohlson
Clas Ohlson EMT446/MD Manual de usuario
Clas Ohlson
Clas Ohlson EMD300A-UK Manual de usuario
Clas Ohlson
Clas Ohlson EMT1700P Manual de usuario
Clas Ohlson
Clas Ohlson 32-4934 Manual de usuario
Clas Ohlson
Clas Ohlson EMR7370 Manual de usuario
Clas Ohlson
Clas Ohlson EMD500 Manual de usuario
Clas Ohlson
Clas Ohlson 18-2146 Manual de usuario
Clas Ohlson
Clas Ohlson KN-S1005TG Manual de usuario
Clas Ohlson
Clas Ohlson EMT445PCS Manual de usuario
Clas Ohlson
Clas Ohlson EMW100T Manual de usuario
Clas Ohlson
Clas Ohlson VE545 Manual de usuario
Clas Ohlson
Clas Ohlson WX0009 Manual de usuario
Clas Ohlson
Clas Ohlson HSW0301D Manual de usuario
Clas Ohlson
Clas Ohlson Welkin AV-302 Manual de usuario
Clas Ohlson
Clas Ohlson 4PET0402A Manual de usuario
Clas Ohlson
Clas Ohlson MA-001 Manual de usuario
Clas Ohlson
Clas Ohlson EFP700DA Manual de usuario
Clas Ohlson
Clas Ohlson HD-420 Manual de usuario
Clas Ohlson
Clas Ohlson HD4201 Manual de usuario
