Clas Ohlson BW6200 Manual de usuario
SUOMINORSKSVENSKAENGLISH
2
3
3
Please read the entire instruction manual
before using and save it for future use.
We apologise for any text or photo errors
and any changes of technical data.
If you have any questions concerning
technical problems please contact our
Customer Service Department (see
address on reverse.)
Product description
To remember
Usage
Advanced usage
Care and maintenance
Troubleshooting
Waste disposal
Specications
ENGLISH
2
3
3
This remote control is manufactured pre-
programmed and replaces up to 6 separate
remote controls for controlling, for example,
TVs, VCRs, satellite and digital TV receivers,
and DVD players. You only have to enter the
correct device code and your URC will be
ready for use. A list of device codes is found
at the very end of this instruction manual. The
URC can also be taught (programmed) by
existing remote controls.
- Pre-programmed for most existing
brands.
- Replaces damaged or lost remote
controls.
- Replaces up to 6 remote controls, for
example for TVs, VCRs, satellite and
digital TV receivers, and DVD players.
- Function for Teletext.
- Operated with 4 x R03/AAA batteries (not
included)
- The remote control is compatible with
most brands on the market but it might
not be compatible with your specic
model of the device. Even if the brand
is included in the code list.
- It is not possible to see in the code list if
the remote control ts your specic device
model, you have to try it out.
- The remote control may work with more
codes than one. One has to try it out until
nding the code that works with the most
buttons.
ENGLISH
4
5
5
When a button is pressed, the display is lit for
about 15 seconds, thereafter the display goes
into a sleep mode (energy saving mode).
Press the display again to activate the buttons
and the display.
The display’s buttons only react to button
presses as long as the display is lit. The direct
buttons react even when the display is in
sleep mode.
Button Sound
All buttons give off a low beep when pressed.
The button sound cannot be turned off.
VO L+
VO L-
P- P +
5
4
1
2
7
3
8
10
6
9
ENGLISH
4
5
5
The touch screen’s buttons
1. Infrared sender
2. LED indicator
3. Touch screen
4. Function buttons
5. Battery lid (on the back)
6. Device buttons (device modes,
buttons for selecting device)
7. Function buttons
8. Mute button (TV sound on/off)
9. SHIFT button (for the SHIFT function)
10.PAGE button (turn to next page of
button set)
On the lower part of the remote control,
there are 9 direct buttons with the following
functions:
Circuit breaker ON/OFF
P+ Programme/Channel up
P- Programme/Channel down
VOL+ Volume up
VOL- Volume down
GREEN button Quick button for, among
other things, Teletext
RED button Quick button for, among
other things, Teletext
YELLOW button Quick button for, among
other things, Teletext
BLUE button Quick button for, among
other things, Teletext
Note: Green, red, yellow and blue buttons
are also used by some satellite and cable TV
receivers.
ENGLISH
6
7
7
The remote control is operated with
4 x R03/AAA batteries.
1. Remove the battery lid on the backside.
2. Put in the batteries according to the
marking in the battery compartment.
Remember to turn the batteries right with
plus (+) and minus (-) according to the
marking.
3. Put the battery lid back.
Low batteries
If the battery symbol is shown in the
display the batteries are starting to go low.
You then have to replace the batteries with
new ones.
ENGLISH
6
7
7
Entering device code
Enter the code in the following manner:
1. Open the included code list and look
under the headline for the type of device
that corresponds to your equipment.
TV Brands – Codes for TVs
VCR Brands – Codes for VCRs
SAT Brands – Codes for satellite recei-
vers as well as codes for digital receivers
for cable TV and terrestrial television
broadcasting.
CBL Brands – Codes for analogue cable
TV receivers.
DVD Brands – Codes for DVD players.
Under this headline you then look for the
code that corresponds to the brand of
your device, for example Philips. Every
code contains 4 digits. If there is more
than device code for your brand, you
begin with the rst one.
2. Turn on, for example, the TV manually or
with the original remote control. Choose
channel 1.
3. Press the button for desired device,
for example [ TV ]. The symbol for the
chosen function ashes.
4. Press the buttons [ P+ ] and [ VOL- ]
simultaneously for 3 seconds until the
LED light is lit.
5. Enter your four digit device code with the
buttons [ 0 ] – [ 9 ].
The LED light ashes a few times and
then goes off.
Test the function of the remote control with
the device that you have just programmed.
If the device responds correctly to the but-
tons you press, you have entered the right
device code. Otherwise, you will have to
repeat the procedure above with the other
device codes available for your brand until
your device reacts in the right way when
you press the buttons and until most buttons
work correctly.
ENGLISH
8
9
9
In the same manner, you set the device
codes for other devices as well. Just
remember to press the button for device
type in step 3 above.
Note
If the LED light ashes 6 times while
entering the four digit device code the
programming has been interrupted for one
of the following reasons:
1. No digit has been pressed during an 8
second period.
2. An invalid device code has been ente-
red.
3. The device code has not been entered
correctly. The device code may only
contain the numbers 0-9.
Programming a new device code for a
chosen device type automatically replaces
the old code.
[ TV ] – the button can only save TV
codes.
[ VCR ] – the button can only save VCR
codes.
[ DVD ] and [ SAT ] – the buttons can
save all device codes (including TV and
VCR codes)
Tip!
When you have found the correct device
code we recommend that you write down
the code on the label on the backside of
the remote control.
If no device code works with your device
If you cannot nd the correct device code
for your device you can search through all
the remote control’s codes for the respec-
tive device type.
TV - TVs
VCR - VCRs
SAT - Satellite and digital TV receivers
DVD - DVD players
ENGLISH
8
9
9
If you cannot nd the right device code
in the list, you can search in the following
manner:
1. Turn on, for example, the TV manually
or with the original remote control.
2. Press the button for the desired device,
for example [ TV ]
First press the [ SHIFT ] button and
then button for desired device.
3. Press the buttons [ P+ ] and [ VOL- ]
simultaneously for 3 seconds until the
LED light is lit.
4. Enter the corresponding search code
from the following table.
The LED light ashes 2 times and is
then turned off.
Device type Search code
TV 0001
VCR 0002
SAT 0003
CBL 0004
DVD 0005
(In this example, you press the code for
TV: 0001)
5. Again, press the same button as in step
2 for desired device type.
(In this example the [ TV ] button).
6. Press the buttons [ P+ ] and [ VOL- ]
simultaneously for 3 seconds until the
LED light is lit. Now the remote control is
ready to search.
7. Point the remote control towards desired
device (in this example, the TV) and
press the button ON/OFF several
times slowly and with patience until the
device is turned off. When the device
has turned off, you immediately press
the device button (for this example
[ TV ] ) to store the search code. The
LED light is turned off.
ENGLISH
10
10
11
11
11
11
In the same manner as above, search for the
device code for other devices. Remember
to press the correct button for the desired
device in steps 2 and 5 above.
Important!
If the circuit breaker function on your device
is not controlled by infrared lights, you follow
steps 2 through 6 above and start the search.
Then, follow the instructions below.
- Press alternately on the button ON/OFF
and another important function button
until your device reacts with the desired
function. Press the button for the device
you have chosen in the steps above (in
this example the [ TV ] button) to store
the search code.
For example, you press alternately
on ON/OFF and another important
function button or on ON/OFF and
PLAY ►.
- Every time that you press the button
ON/OFF the remote control skips to
the next code and send out a signal for
turning off the device. If you do not ma-
nage to stop pressing ON/OFF in time
before the device is turned off, you turn
on the device as fast as you can. Before
the indicator (the LED light) is turned
off you press [ P- ] to skip backwards.
Repeat step 7 above and store the code.
- If the LED light ashes 6 times after that
you have pressed ON/OFF , you have
reached the library’s last code. Press
on (in this example [ TV ] ) to restore
the remote control and repeat the above
procedure to search again.
Note
DVD, SAT and other device codes may be
stored on all function buttons except TV and
VCR.
ENGLISH
Tabla de contenidos
Idiomas:
Otros manuales de Mando a distancia de Clas Ohlson
Clas Ohlson
Clas Ohlson ML-C Manual de usuario
Clas Ohlson
Clas Ohlson LD-SCB01 Manual de usuario
Clas Ohlson
Clas Ohlson PP-iDual-IR iD RC Manual de usuario
Clas Ohlson
Clas Ohlson 50027 Manual de usuario
Clas Ohlson
Clas Ohlson BW8380EU Manual de usuario
Clas Ohlson
Clas Ohlson SR1000 Manual de usuario
Clas Ohlson
Clas Ohlson EMW100TM Manual de usuario
Clas Ohlson
Clas Ohlson BW0881 Manual de usuario
