Clarke CDDFTP Manual de usuario

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

MODEL NO: CDDFTP

PART NO:

PART NO: 6499680

Fuel Transfer Pump

INTRODUCTION

Thank you for purchasing this CLARKE Double Diaphragm Fuel Transfer Pump,

This pump is designed for use with non-corrosive petroleum based products of light to medium viscosity such as petrol,

diesel,fuel oil and motor oils. It should not be used with solvents,acids,alkalis,or other corrosive liquids

Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully.

SAFETY

To ensure safe and efficient operation, it is essential to read and follow each of these warnings and precautions.

1. When used to pump flammable liquids, improper use or installation of this product can cause serious bodily injury or

death.

2. Do NOT smoke near the pump or use the pump near an open flame. Fire could result.

3. When pumping flammable liquids, all equipment must be grounded to prevent the build up of static electricity

which may ignite vapours or gases. The pump and containers should be connected using bonding clamps or clips

and a conductive wire no smaller than 12 gauge. A secure and positive metal to metal contact must be made. The

other end of the wire should be attached to a good ground, such as a steel building column or water pipe.

SPECIFICATIONS

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12 months from the date of

purchase. Please keep your receipt which will be required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or tampered with in any way, or not

used for the purpose for which it was intended.

Faulty goods should be returned to their place of purchase, no product can be returned to us without prior

permission.

This guarantee does not effect your statutory rights.

Barrel Collar Size 2” BSP Outlet Tube Diameter 27 mm

Inlet Tube Diameter 26 mm Product Weight 5.6 kg

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

ASSEMBLY

FITTING THE PUMP TO A BARREL

1. Assemble the pump as shown above. Use PTFE tape (not supplied) at all connections

2. Screw the threaded collar into the opening of the barrel.

3. Tighten the collar bolt to the pump body.

USING THE PUMP

1. Make sure all connections are secure and place a suitable container under the spout.

2. Pump the handle to draw fluid from the barrel.

• The first time you use the pump, liquid should begin flowing after several pumps of the handle

CLEANING THE FILTER

1. Remove the four bolts that connect the Inlet to the pump.

2. Remove the filter holder and filter.

3. Wash the filter of any contaminants.

4. Replace the filter holder and filter.

5. Reattach the Inlet and secure with the four bolts.

WHAT IS SUPPLIED ASSEMBLED

CAUTION: DO NOT USE THE PUMP IF THE FILTER. IS DAMAGED OR

BLOCKED.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Bomba de agua de Clarke

Clarke

Clarke CRWP1 Manual de usuario

Clarke

Clarke MSP12 Manual de usuario

Clarke

Clarke CPE30A1 Manual de instrucciones

Clarke

Clarke DFT230 Manual de instrucciones

Clarke

Clarke SPE800 Manual de instrucciones

Clarke

Clarke SUBMERSIBLE PUMP Manual de instrucciones

Clarke

Clarke PF75A Manual de instrucciones

Clarke

Clarke CVPW Guía rápida

Clarke

Clarke PSV6A Manual de instrucciones

Clarke

Clarke HSE Series Manual de instalación y operación

Clarke

Clarke PW2 Manual de instrucciones

Clarke

Clarke DWP210A Manual de instrucciones

Clarke

Clarke CU150 Manual de instalación y operación

Clarke

Clarke TAM100 7230035 Manual de instalación y operación

Clarke

Clarke ECP15A1 Manual de instrucciones

Clarke

Clarke CBM240E Manual de instrucciones

Clarke

Clarke CSE400A Manual de instrucciones

Clarke

Clarke CHF2 Manual de instalación y operación

Clarke

Clarke CPRP560 Manual de instrucciones

Clarke

Clarke PSV7A Manual de instrucciones

Clarke

Clarke SPE800 Manual de instalación y operación

Clarke

Clarke CSE2 Manual de instrucciones

Clarke

Clarke CBM100SS Manual de instalación y operación

Clarke

Clarke ISP14A Manual de instalación y operación

Manuales populares de Bomba de agua de otras marcas

Neptun

Neptun NPHW 5500 Manual de usuario

Sensidyne

Sensidyne Gilian BDX-II Instrucciones de instalación y funcionamiento

Draper

Draper 47808 Manual de usuario

Trolla

Trolla 12820 Manual de usuario

Sunfab

Sunfab SVH Series Manual de usuario

WilTec

WilTec 50740 Manual de usuario

Fieldmann

Fieldmann FVC 5015 EK Manual de usuario

Everbilt

Everbilt EFSUB5-122HD Manual de usuario

Graco

Graco Husky 3300e Manual de usuario

esotec

esotec 101018 Manual de usuario

moyno

moyno 2000 CC Manual de usuario

Becker

Becker BASIC VASF 2.80/1-0.AC230 Manual de usuario

Sykes AmeriPumps

Sykes AmeriPumps GP100M Guía de solución de problemas

DUROMAX

DUROMAX XP WX Series Manual de usuario

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Manual de usuario

Franklin Electric

Franklin Electric IPS Manual de usuario

Xylem

Xylem e-1532 Series Manual de usuario

Milton Roy

Milton Roy PRIMEROYAL Manual de usuario