Clarke CONTRACTOR CON185B Manual de instrucciones

OPERATION & MAINTENANCE

INSTRUCTIONS

DL0222

ORIGINAL INSTRUCTIONS

185MM CIRCULAR SAW WITH LASER GUIDE

(230V)

MODEL NO: CON185B

PART NO: 6462502

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this CLARKE 185mm (230V) Circular Saw.

Before attempting to use this product, please read this manual thoroughly and

follow the instructions carefully. In doing so you will ensure the safety of yourself

and that of others around you, and you can look forward to your purchase

giving you long and satisfactory service.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission.

This guarantee does not effect your statutory rights.

ENVIRONMENTAL PROTECTION

Recycle unwanted materials instead of disposing of them as waste. All

unwanted accessories and packaging should be sorted and taken to a

recycling centre for disposal in a manner which is compatible with the

environment.

ENVIRONMENTAL RECYCLING POLICY

Through purchase of this product, the customer is taking on the

obligation to deal with the WEEE in accordance with the WEEE

regulations in relation to the treatment, recycling & recovery and

environmentally sound disposal of the WEEE.

In effect, this means that this product must not be disposed of with general

household waste but according to the laws governing Waste Electrical and

Electronic Equipment (WEEE) at a recognised disposal facility.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

SPECIFICATIONS

SAFETY SYMBOLS

Model Number CON185B

Rated Voltage 230V~50Hz

Power Input 1500 W

IP Rating IPX0

No Load Speed 4700 RPM

Maximum Depth of Cut 63 mm @ 90o- 43 mm @ 45o

Dust Port Dimension 35mm (Internal)

Laser Guide Class 2 Laser

Blade Dimensions 185 mm Ø x 2.5 mm (thickness) x 20 mm Bore

Sound Pressure Level LpA 94 dB(A)

Sound Power Level LWA 106 dB(A) - Uncertainty Factor (K): 3dB(A)

Vibration 4.26 m/s2- Uncertainty Factor: 1.5m/s2

Weight 5.25 kg

Dimensions (L x W x H) 300 mm x 245 mm x 170 mm

Fully read this

manual and safety

instructions before

use

Eye protection

should be worn

Ear protection

should be worn

Dust mask should be

worn

Warning: Laser

Radiation, Class 2

Laser: DO NOT stare

into the beam

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

OVERVIEW.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

CARTON CONTENTS

The following items should be supplied in the carton. If any parts are missing or

damaged, please contact the CLARKE dealer where you purchased the tool.

• 1 x 1500 Watt Circular Saw.

• 1 x 185 mm Ø x 20 mm Bore x 24 Tooth TCT blade.

• 1 x Parallel Guide.

• 1 x 6 mm Hexagon Key.

1 Dust Extraction Outlet 11 Laser Guide On/Off Switch

2 Laser Guide 12 Motor

3 Parallel Guide 13 Main Handle

4 Mark For Straight Cut 14 Safety Button

5 Mark For Bevel Cut 15 On/Off Trigger

6 Bevel Locking Screw 16 Depth Adjustment Lever & Scale

7 Bevel Scale 17 Blade Guard Retracting Lever

8 Parallel Guide Locking Screw 18 Blade Clamping Screw

9 Blade Lock 19 185mm Blade

10 Auxiliary Handle 20 6mm Hexagon Key (Not Shown)

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

POWER TOOL SAFETY WARNINGS

WORK AREA

1. Keep the work area clean and well lit. Cluttered and dark areas invite

accidents.

2. DO NOT operate this saw in explosive atmospheres, such as in the presence

of flammable liquids, gases or dust. Power tools create sparks which may

ignite the dust or fumes.

3. Keep children and bystanders away while operating this saw. Distractions

can cause you to lose control.

ELECTRICAL SAFETY

1. The saw plug must match the outlet. NEVER modify the plug in any way. DO

NOT use adaptor plugs with earthed (grounded) power tools. Unmodified

plugs and matching outlets will reduce the risk of electric shock.

2. DO NOT expose the saw to rain or wet conditions. Water entering the saw

will increase the risk of electric shock.

3. DO NOT abuse the cable. NEVER use it for carrying, pulling or unplugging

the saw. Keep the cable away from heat, oil, sharp edges or moving parts.

Damaged or entangled cables increase the risk of electric shock.

4. When operating the saw outdoors, use an extension cable suitable for

outdoor use. Use of a cable suitable for outdoor use reduces the risk of

electric shock.

5. If operating the saw in a damp location is unavoidable, use a residual

current device (RCD) protected supply.

PERSONAL SAFETY

1. Stay alert, watch what you are doing and use common sense when

operating the saw. DO NOT use this saw while you are tired or under the

influence of drugs, alcohol or medication. A moment of inattention while

operating power tools may result in personal injury.

2. Use safety equipment. ALWAYS wear eye protection. Safety equipment

such as dust mask, non-skid safety shoes, hard hat, or hearing protection

used for appropriate conditions will reduce personal injuries.

3. Avoid accidental starting. Ensure the switch is in the off position before

plugging in. Carrying this saw with your finger on the switch or plugging in

invites accidents.

4. Remove any hex key before turning the saw on. A hex key left attached to

a rotating part may result in personal injury.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

5. DO NOT overreach. Keep proper footing and balance at all times. This

enables better control of the saw in unexpected situations.

6. Dress appropriately, DO NOT wear loose clothing or jewellery. Keep your

hair, clothing and gloves away from moving parts. Loose clothes, jewellery

or long hair can be caught in moving parts.

POWER TOOL USE AND CARE

1. DO NOT force the saw. Use the correct accessories for your application.

The correct power tool will do the job better and safer at the rate which it

was designed for.

2. DO NOT use the saw if the switch does not turn it on and off. Any power tool

that cannot be controlled with the switch is dangerous and SHOULD NOT

be used until it has been repaired.

3. Disconnect the plug from the power source before changing accessories,

or storing the saw. Such preventive safety measures reduce the risk of

starting the saw accidentally.

4. Store idle tools out of the reach of children and DO NOT allow persons

unfamiliar with the saw or these instructions to operate it. Power tools are

dangerous in the hands of untrained users.

5. Check for misalignment or binding of moving parts, breakage of parts and

any other condition that may affect the saw’s operation. If damaged,

have the saw repaired before use. Many accidents are caused by poorly

maintained power tools.

6. Use the saw and accessories in accordance with these instructions and in

the manner intended, taking into account the working conditions and the

work to be performed. Use of the saw for operations different from

intended could result in a hazardous situation.

7. The performance of this saw may vary, depending upon variations in line

voltage. Extension cable usage may also affect performance.

SERVICE

1. Have your saw serviced by qualified service personnel using only identical

replacement parts. This will ensure that the safety of the saw is maintained.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

SAFETY INSTRUCTIONS FOR ALL SAWS

1. Keep hands away from cutting area and the blade. Keep your second

hand on the auxiliary handle, or motor housing. If both hands are holding

the saw, they cannot be cut by the blade.

2. DO NOT reach underneath the workpiece. The guard cannot protect you

from the blade below the workpiece.

3. Adjust the cutting depth to the thickness of the workpiece. Less than a full

tooth of the blade teeth should be visible below the workpiece.

4. NEVER hold the piece being cut in your hands or across your leg. Secure

the workpiece to a stable platform. It is important to support the work

properly to minimise body exposure, blade binding or loss of control.

5. ALWAYS hold the saw by the insulated gripping surfaces when performing

an operation (see page13). Contact with a ”live” wire will also make

exposed metal parts of the power tool”live” and shock the operator.

6. ALWAYS use blades with the correct size and shape of arbor holes. Blades

that do not match the mounting hardware of the saw will run eccentrically,

causing loss of control.

7. NEVER use damaged or incorrect blade washers or bolt. The blade washers

and bolt were specially designed for your saw, for optimum performance

and safety of operation.

8. DO NOT operate the saw if the guard is damaged or does not operate

correctly.

9. NEVER use the saw with the guard removed.

CIRCULAR SAW BLADE SAFETY WARNINGS

1. The maximum speed listed for the saw (see page 3) should not exceed the

maximum speed marked on the blade.

2. Cracked circular saw blades should be scrapped (repairing is not

permitted). Composite (tipped) circular saw blades, where the tip

dimension is reduced to less than 1 mm, should be taken out of service.

3. Fastening screws and nuts should be tightened using the tools supplied.

4. Clamping surfaces should be cleaned to remove dirt, grease, oil and

water.

5. DO NOT use loose rings or bushes to “make up”bore sizes on circular saw

blades.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

PREVENTION OF KICKBACK

Kickback is a sudden reaction to a pinched, bound or misaligned saw blade,

causing an uncontrolled saw to lift up and out of the workpiece toward the

operator.

When the blade is pinched or bound tightly by the kerf closing down, the

blade stalls and the motor reaction drives the unit rapidly back toward the

operator.

If the blade becomes twisted or misaligned in the cut, the teeth at the back

edge of the blade can dig into the top surface of the wood causing the

blade to climb out of the kerf and jump back toward the operator. Kickback is

the result of saw misuse and/or incorrect operating procedures or conditions

and can be avoided by taking proper precautions as given below.

1. Maintain a firm grip with both hands on the saw and position your arms to

resist kickback forces. Position your body to either side of the blade, but not

in line with the blade.

2. When the blade is binding, or when interrupting a cut for any reason,

release the trigger and hold the saw motionless in the material until the

blade comes to a complete stop. NEVER attempt to remove the saw from

the work or pull the saw backward while the blade is in motion or kickback

may occur. Investigate and take corrective actions to eliminate the cause

of blade binding.

3. When restarting a saw in the workpiece, centre the saw blade in the kerf

and check that saw teeth are not engaged with the material. If the blade

is binding, it may walk up or kickback from the workpiece as the saw is

restarted.

4. Support large panels to minimise the risk of blade pinching and kickback.

Large panels tend to sag under their own weight. Supports must be placed

under the panel on both sides, near the line of cut and near the edge of

the panel.

5. Blade depth and bevel adjusting locking screws must be tight and secure

before making a cut. If blade adjustment shifts while cutting, it may cause

binding and kickback.

6. Use extra caution when making a “plunge cut” into existing walls or other

blind areas. The protruding blade may cut objects that can cause

kickback.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

ELECTRICAL CONNECTIONS

Before switching the product on, make sure that the voltage of your electricity

supply is the same as that indicated on the rating plate. This product is

designed to operate on 230VAC 50Hz. Connecting it to any other power

source may cause damage.

This product may be fitted with a non-rewireable plug. If it is necessary to

change the fuse in the plug, the fuse cover must be refitted. If the fuse cover

becomes lost or damaged, the plug must not be used until a suitable

replacement is obtained.

If the plug has to be changed because it is not suitable for your socket, or due

to damage, it should be cut off and a replacement fitted, following the wiring

instructions shown below. The old plug must be disposed of safely, as insertion

into a mains socket could cause an electrical hazard.

If the colours of the wires in the power cable of this product do not correspond

with the markings on the terminals of your plug, proceed as follows.

• The wire which is coloured Blue must be connected to the terminal

which is marked Nor coloured Black.

• The wire which is coloured Brown must be connected to the terminal

which is marked Lor coloured Red.

We strongly recommend that this machine is connected to the mains supply

via a Residual Current Device (RCD)

This symbol indicates that this is a Class II product, and does not require

an earth connection.

WARNING: READ THESE ELECTRICAL SAFETY INSTRUCTIONS

THOROUGHLY BEFORE CONNECTING THE PRODUCT TO THE MAINS

SUPPLY.

Plug must be BS1363/A approved.

Always fit a 13 Amp fuse.

Ensure that the outer sheath of the cable is firmly held by the clamp

Neutral

(Blue)

Live

(Brown)

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sierra de Clarke

Clarke

Clarke CMSF110 Manual de instalación y operación

Clarke

Clarke C2MS210MP Manual de instrucciones

Clarke

Clarke CCS185 Manual de instrucciones

Clarke

Clarke MBS600D Manual de usuario

Clarke

Clarke CT4014 Manual de usuario

Clarke

Clarke CAT118 Manual de instalación y operación

Clarke

Clarke Woodworker CTS10PLM Manual de instalación y operación

Clarke

Clarke CPS160 Manual de instrucciones

Clarke

Clarke CBS 190 Manual de instalación y operación

Clarke

Clarke CCO14C Manual de instrucciones

Clarke

Clarke CONTRACTOR CON850B Manual de instrucciones

Clarke

Clarke Woodworker CBS12WC Manual de instalación y operación

Clarke

Clarke Metalworker CBS45MD Manual de instrucciones

Clarke

Clarke CBS 355 Manual

Clarke

Clarke CMS216S Manual de instrucciones

Clarke

Clarke CTS11 Manual de instalación y operación

Clarke

Clarke CCO14B Manual de instrucciones

Clarke

Clarke CMS10S2 Manual de instrucciones

Clarke

Clarke METALWORKER CBS 7MC Manual

Clarke

Clarke Contractor CCS2 Manual de instalación y operación

Clarke

Clarke WOODWORKER CBS205 Manual de instrucciones

Clarke

Clarke CSS 300 Manual de funcionamiento

Clarke

Clarke Contractor CFIS 250 Manual de instalación y operación

Clarke

Clarke WOODWORKER CMS10S Manual

Manuales populares de Sierra de otras marcas

RIDGID

RIDGID BS1400 Manual de usuario

ATIKA

ATIKA BWS 400-2 Manual de usuario

RGC

RGC FS20 Manual de usuario

Makita

Makita M2300 Manual de usuario

IMET Spa

IMET Spa BASIC 300 PLUS SHI Manual de usuario

IMET Spa

IMET Spa SIRIO 370 AF-E Manual de usuario

Optimum

Optimum OPTisaw CS 275 Manual de usuario

Makita

Makita BPB180 Manual de usuario

Stihl

Stihl MS 462 C-M Manual de usuario

AEG

AEG TS 250 K Manual de usuario

Meec tools

Meec tools 004665 Manual de usuario

Makita

Makita LS1018L Manual de usuario

Ryobi

Ryobi RCS1400 Manual de usuario

DeWalt

DeWalt DCS391 Manual de usuario

Sealey

Sealey SA72 Manual de usuario

skilsaw

skilsaw SPT88 Instrucciones de montaje

Urrea

Urrea SI810 Dimensiones y guía de instalación

EINHELL

EINHELL BKG 210/1 Manual de usuario