Clarke JetKing 2000 Manual de instalación y operación

POWER WASHER

OPERATING & MAINTENANCE

INSTRUCTIONS

0298

Thank you for purchasing this JetKing 2000 Power washer

This machine is a lightweight, portable, high pressure power washer, designed for

DIYuse in and around the home.

It comprises an electric motor, a pump, a high pressure hose with a trigger and

lance, and an adaptor for injecting foam or cleaning agents into the water jet,

ideal for cleaning greasy engines and equipment, removing oil spots from patios

etc.

Before attempting to use your JetKing, please read this instruction manual

thoroughly and follow all instructions carefully. By doing so you will ensure the

safety of yourself and that of others around you, and you can look forward to it

giving you long and satisfactory service.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12 months

from the date of purchase. Please keep your receipt as proof of purchase. This

guaranteeisinvalidiftheproductisfoundtohavebeenabusedortamperedwith

in any way, or not used for the purpose for which it was intended.

Faulty goods should be returned to their place of purchase, no product can be

returned to us without prior permission. This guarantee does not effect your

statutory rights.

Before assembling your new Powerwasher, check to ensure that all parts listed

below are included.

• JetKing Powerwasher with cable and plug.

• Trigger/Handle assembly with high pressure hose.

• Lance with nozzle assembly.

• Inlet hose connector.

• Detergent/foam attachment with plastic container.

• Bag containing one wire prod (for unblocking nozzle. should it become

necessary) and a Hose Securing Clip (Spare Parts, item no. 9)

SAFETY PRECAUTIONS

WARNING

Water at high pressure can be dangerous and may cause severe damage to

persons or property if improperly used.

NEVER allow anyone to operate this equipment unless they are thoroughly

reliable, and completely familiar with the safety precautions.

1. Never direct the spray jet at any person or animal.

2. Never hold a finger over the high pressure nozzle.

3. Never direct the spray jet at the machine itself or any other electrical

equipment.

4. After use,and before disconnecting hoses,release the pressure in the high

pressure hose by operating the trigger.Do not attempt to disconnect any

hose or coupling with pressure still in the hose.

5. Never operate the machine with any of the covers removed.

6. Do not,attempt any electrical or mechanical repair.If you have a problem

with your machine contact your local dealer or Machine Mart Service Dept.,

tel: 0115 9561809

7. Never supply any liquid other than water to the water inlet.

8. Use only chemical cleaning agents approved for power washing.

9. Never usethe foamattachment tointroducesolventseg.paint thinners,petrol,

oil,etc.

10. Do not operate the machine whilst standing on ladders: use a platform tower

or scaffolding.

11. Children should not be allowed to use the machine.

12. We recommendthe use ofsafety goggles when usingthis machineespecially

where loose particles of stone or grit etc.may be blown around by the high

pressure spray.

13. Whennot inuse,disconnectfromthe waterandelectricalsupply’s,and ensure

the system is completely drained.Store in a dry,frost free environment.

14. Disconnect from the mains supply before carrying out any maintenance or

servicing.

15. Never carry the washer by the power cable,or yank it to disconnect from the

socket.Keep the cable away from heat,oil or sharp edges.

16. DO NOT run machine OFF LOAD for longer than 1 minute.Always switch off

and restart when required. 3

ELECTRICAL CONNECTIONS

WARNING: THIS MACHINE MUST BE EARTHED.

This product is provided with a standard 13 amp, 230 volt (50Hz), BS 1363 plug, for

connection to a standard, domestic electrical supply.

Should the plug need changing at any time, ensure that a plug of identical

specification is used. IMPORTANT: The wires in the mains lead should be wired up

in accordance with the following colour code:

Green & Yellow —- Earth

Blue —- Neutral

Brown —- Live

Asthecoloursofthewiresinthemainsleadmaynotcorrespondwiththecoloured

markings identifying the terminals in your plug, proceed as follows:

Connect GREEN & YELLOW coloured cord to plug terminal marked

with a letter “E” or Earth symbol “ “.

Connect BROWN coloured cord to plug terminal marked letter “L”

Connect BLUE coloured cord to plug terminal marked letter “N”

We strongly recommend that this machine is connected to the mains supply

through a Residual Current Device (RCD).

FUSE RATING

The fuse in the plug for this appliance must be rated at 13 amps

IMPORTANT:

If this appliance is fitted with a plug which is moulded onto the electric cable (i.e.

non-rewirable) :

1. The plug must be thrown away if it is cut from the electric cable. There is a

danger of electric shock if it is subsequently inserted into a live socket outlet.

2. Never use the plug without the fuse cover fitted.

3. Should you wish to replace a detachable fuse carrier, ensure that the correct

replacement is used (as indicated by marking or colour code).

4. Replacement fuse covers can be obtained from your local dealer or most

electrical stockists.

5. The fuse in the plug must be replaced with one of the same rating (13 amps)

and this replacement must be approved to BS1362.

EXTENSION CABLES

If an extension cable is used, always ensure it is fully unwound. When used

outdoors, ensure the extension cable is specifically designed for outdoor use.

The maximum extension length is 25 metres. Ensure that the wire sizes in the cable

is at least 1.5mm2in cross section. As a general rule, the extension cable must be

thicker than the cable supplied with the washer.

IF IN DOUBT, CONSULT A QUALIFIED ELECTRICIAN.

Do not attempt any electrical repairs yourself.

ASSEMBLY AND PREPARATION FOR USE.

A. High Pressure Hose (2)

At one end of the hose is a spigot,fitted with an O-ring.Push this end firmly into the

water inlet port of the handle and lance assembly, and insert the Hose Securing

Clip (Spare Parts list,item 9),ensuring it is fully home.It is correctly fitted when the

‘U’ bend of the clip sits snugly in the groove provided, allowing the protecting

shroud to be pushed over the connection until it clicks into place.

Remove the plastic travel cap from the threaded high pressure outlet (6), and

screw on the high pressure hose (2) firmly.

B. Lance Extension (3)

At the opposite end to the nozzle (4) is a spigot (5) with two integral lugs,and a

rubber O-ring.Ensure the O-ring is in place and in good condition.

Insert the spigot end of the lance extension into the trigger/handle assembly (1).

Push home firmly and twist to lock it in position.DO NOT attempt to disassemble

the trigger/handle assembly.

NOTE: When new, the lance extension may be a tight fit and a little lubrication,

with vaseline or similar,will assist when joining the parts together.

C. Water Supply Hose

Remove the temporary travel cap from the threaded inlet port (7),on the front of

the unit.

IMPORTANT: Check to ensure that the filter is correctly located inside the inlet port

Screw on the Inlet Hose Adapter,ensuring the rubber sealing ring is in place.This

connection must be tight to avoid leaks.

Attach a suitable 1/2” hose to the inlet hose adapter (6),using a standard type

snap-on connector (not supplied), available from all good DIY and Hardware

Stores.

Secure the other end of the hose to your tap using a suitable tap adaptor (not

supplied)

Cold or hot water (up to 50°C) can be used.

NOTE:

1. In some areas,it may be necessary to ensure that you comply with local

bylaws concerning the use of water from the mains supply,and the disposal

of possibly contaminated water.

2. Hose,worm drive clips and other accessories are readily available from all

good DIY,Hardware and Garden Supplies Stores.

OPERATION

1. Make certain the ON/OFF switch,located on the rear panel of the unit,is set

in the OFF position.

2. Connect theplugto themainssupply,preferablyviaa ResidualCurrentDevice.

3. Turn the water tap fully on.Remember - NEVER attempt to run the machine

with the water supply disconnected,or turned off.

When starting,you should always adopt the following procedure:

In order to ease the starting process,and to prevent the possibility of blown fuses,

pull the trigger on the lance and hold in that position whilst switching the motor

ON and allowing the pump to develop full pressure.

NOTE: Itmaybenecessary toreleasethe safetylatchin orderto releasethe trigger,

by pushing the button,on the right side of the trigger assembly,IN.

You may release the trigger once full pressure is developed.When you do so,the

motor will continue run,and the bypass will come into effect,accompanied by a

noticeable change in motor noise.

As soon as you pull the trigger again,the bypass will close and water at pressure

will be ejected.

WARNING

ENSURE THE OPERATOR IS AWARE THAT WHEN THE TRIGGER IS PULLED, WATER AT

HIGH PRESSURE CAN CAUSE THE LANCE TO KICK

- IT SHOULD THEREFORE BE HELD FIRMLY.

IN ADDITION, CARE MUST BE TAKEN TO ENSURE THAT THE NOZZLE IS NOT AIMED

AT AN AREA WHERE THE WATER JET WILL CAUSE DAMAGE.

i.e. AWAY FROM PEOPLE, ANIMALS, WINDOWS - GREENHOUSES ETC., AND BE

AWARE THAT SPLASH BACK COULD ALSO CAUSE DAMAGE IF THE JET IS

TRAINED ON A NEARBY WALL ETC.

IMPORTANT: NEVER run the machine ‘off load’ for long periods, (greater than 1

minute),without pulling the trigger,as damage to the pump will eventually occur.

A fan or pencil spray is possible

by twisting the nozzle as shown

in the diagram.

Pump pressure is factory set

and cannot be adjusted. A

pressure of 100bar is sufficient

to blast off dirt and grime from

patiosandbrickworkwithease.

To reduce water pressure at thenozzle and to givea wider distribution of waterfor

rinsing etc., turn the nozzle to produce a fan spray

Whenyouhavefinished withthe machineyou shouldshut downusingthe following

procedure:

1. Switch OFF using the switch mounted on the rear panel of the machine.

2. Disconnect from the mains electrical supply.

2. Turn OFF the water supply at the mains.

3. For safety,pull the trigger to relieve any pressure in the system.

4. Disconnect from the water supply.

5. Disconnect the inlet and high pressure hoses and allow to drain.

6. If the detergent adapter has been used,rinse it thoroughly with clean water.

Store in a dry,frost free location,not exposed to the elements.

CHEMICAL CLEANING AGENTS

To improve cleaning qualities,it is possible to introduce chemical cleaning agents

(detergents) into the spray using the foam attachment.This is particularly useful

for washing cars, greasy engine parts, removing oil spots on concrete etc. Use

ONLYthosedetergentsrecommended foruse withpower washers,suchas‘TRAFFIC

FILM REMOVER’ which is a powerful low foaming agent for car cleaning, patio

cleaning etc.,or‘WASH & WAX’,both available from Machine Mart.

To preparefordetergentapplication,ensurethe trigger safetylatchis settoprevent

the trigger from being pulled accidentally.

Push the detergent attachment,firmly on to the end of the nozzle until you hear or

feel it lock into place.

With the container filled with detergent,screw it on to the detergent attachment

ensuring the plastic pickup tube is in place.

Twist the lance nozzle to select a fan spray which will provide better distribution of

the detergent.Release the trigger safety latch and pull the trigger to spray the

detergent on to the vehicle,patio etc.,and allow it to work itself into the grime.

Bucket

containing

antifreeze

On top of the foam attachment is a yellow knob with a serrated edge,which can

be turned clockwise or anticlockwise to adjust the amount of detergent allowed

intothe water jet.Turntheknob clockwisetoreduce theamount andanticlockwise

to increase.

To rinse and clean,set the trigger safety latch,and remove the foam attachment

as follows:

Pull DOWN on the locking latch, in the

direction of the arrow, as shown in the

diagram, and pull the attachment away

from the nozzle.

Releasethe triggersafety latchand pull the

trigger to blast off the dirt.

After using the detergent attachment,rinse

it, together with the container, thoroughly

with clean water.

IMPORTANT: Ensure you read and comply with the manufacturers instructions

regarding the use of chemical detergents.

CARE AND MAINTENANCE

WARNING: Ensure the plug is removed from the socket before carrying out any

adjustment, servicing or maintenance.

After each use

If cleaning agents have been used,thoroughly clean the detergent attachment

and bottle with clean water.

Storage

Store in an horizontal position.

Ifthere isa dangerof freezing,insert theinlet

and outlet hoses into a bucket of antifreeze

as shown in the diagram,start the machine

and allow the antifreeze to circulate.After

ashort timestopthe machine,andstorewith

the antifreeze still within the pump body.

NOTE:

Ifyou experiencedifficulty in starting the motor following a long periodofstorage,

it is possible that the seals within the pump have dried out and are gripping the

pistons. This problem may be alleviated by storing the machine with antifreeze

within the pump body,as described above.

If the seals are stuck however, disconnect the machine from the electrical and

water supply’s,and proceed to free them as follows:

Insert a screwdriver into the slot provided in the centre of the fan,which is at the

rear of the machine,visible through the grille.Turn the fan with the screwdriver to

free the seals.

Water inlet filter

Located behind the inlet Hose Adapter,this filter should be removed for cleaning

after every 10 hours of use (or less if water is contaminated).

Remove the filter by unscrewing the inlet hose adapter and withdrawing the filter

element.

Clean the element with fresh water. To replace, reverse the above procedure,

ensuring that the inlet hose adapter seal is in place.

TROUBLESHOOTING

Fault Cause Remedy

Machine will not start 1. No electrical power 1. Check cable,plug,fuse

2. Electrical defect 2. Return to service agent

Motor will not rotate 1. Pump seals dry after 1. Disconnect from electrical

period of storage andwatersupply’sandfree

seals - refer to Care &

Maintenance,p8

Machine blows fuses 1. Pump seals dry after 1. Free off pump seals

when starting a period of storage refer to maintenance p8

2. Hard Start 2. Pull trigger when starting

3. Poor electrical 3. Check supply

supply

4. Motor defective 4. Return to service agent

Machine will not 1. Pump sucking in air 1. Check for leaks in hose

come up to pressure 2. Intake filter blocked 2. Clean filter

3. Defective pump 3. Return to service agent

For Spare Parts and Servicing,please contact your nearest dealer,or

MACHINE MART,on one of the following numbers.

PARTS - 0115 956 1805 SERVICE - 0115 956 1809

Please note that the details and specifications contained herein,are correct at the time of going to print.However,

MACHINE MART reserve the right to change specifications at any time without prior notice.

ACCESSORIES

The accessories listed below provide the JetKing with great versatility and are

available from your local branch of Machine Mart.

A. 3-Piece Kit. (Code No. 050420620)

comprising:

1. Large,auto cleaning,soft

bristled Rotary Brush.

2. Drain Cleaner.Exerts a

powerful water jet via its’8

metre flexible hose,which may

also be used as a prod to

remove blockages.

3. Water,Sand Blasting Lance.For

cleaning stonework,masonry,

driveways etc.

B. Turbo Nozzle (Code No.050420622)

Provides rotary cleaning action for

improved cleaning of brickwork,

patios - removing oil stains from

driveways etc.

C. Under Chassis Spray Lance

(Code No. 050420624)

For reaching under vehicles with

the minimum of effort.

SPECIFICATIONS

Motor ............................................................ 230V 50Hz 1Ph

Power Rating ................................................ 1.5HP

Max.Pressure ............................................... 100bar (1500psi)

Max.Water Flow .......................................... 8L/min

Max.Inlet Water Temp. ............................... 50oC

Weight .......................................................... 10.5kg

Part No.......................................................... 050410620

Tabla de contenidos

Otros manuales de Hidrolavadora de Clarke

Clarke

Clarke CWG2 Manual de instalación y operación

Clarke

Clarke TIGER1700 Manual de instrucciones

Clarke

Clarke PLV100LT Manual de instalación y operación

Clarke

Clarke Tiger 2600B Manual de instrucciones

Clarke

Clarke JETSTAR 1850 Manual de instrucciones

Clarke

Clarke KING 145 Guía de solución de problemas

Clarke

Clarke JET 7500 Manual de instrucciones

Clarke

Clarke PLV145H Manual de instalación y operación

Clarke

Clarke TIGER 3000A Manual de instrucciones

Clarke

Clarke King 130 Manual

Clarke

Clarke Power Wash PLS190 Manual de instrucciones

Clarke

Clarke JETSTAR 1800 Manual de instalación y operación

Clarke

Clarke PLV100LB Manual de instalación y operación

Clarke

Clarke KING150B Manual de instrucciones

Clarke

Clarke JETSTAR 1950 Manual de instrucciones

Clarke

Clarke JET 9000B Manual de instrucciones

Clarke

Clarke Power Wash PLS265B Manual de instrucciones

Clarke

Clarke JET 8000 Manual de instrucciones

Clarke

Clarke Power Wash PLS265A Manual de instrucciones

Clarke

Clarke HLS130 Manual de instrucciones

Clarke

Clarke KING 200 Manual de instrucciones

Clarke

Clarke Power Wash PLS195A Manual de instrucciones

Clarke

Clarke Power Wash EHD130 Manual de instalación y operación

Clarke

Clarke JET 8500 Manual de instrucciones

Manuales populares de Hidrolavadora de otras marcas

Shark

Shark RG-232637 Manual de usuario

Shakti Technology

Shakti Technology S3 Manual de usuario

Kärcher

Kärcher K 4 Pure Manual de usuario

Porter-Cable

Porter-Cable D25806-025-2 Manual de usuario

REM POWER

REM POWER HDEm 662 Manual de usuario

Landa

Landa HS-3000 Manual de usuario

Craftsman

Craftsman 580.752270 Manual de usuario

HIKOKI

HIKOKI AW 100 Manual de usuario

Delco

Delco DC 1302 Manual de usuario

Kärcher

Kärcher K 3 Full Control Manual de usuario

BIEMMEDUE

BIEMMEDUE 120/10 - 170/13 Manual de usuario

ARKSEN

ARKSEN 014-HG-14141-HR Manual de usuario

Black & Decker

Black & Decker PW1700SPX Manual de usuario

Kärcher

Kärcher 595 - SPARE Guía

Kranzle

Kranzle B 10 200 Manual de usuario

Stihl

Stihl RE 90 Manual de usuario

Husky

Husky HU80911 Manual de usuario

PowR-Quip

PowR-Quip PQ-2600 Manual de usuario