Clarke CDP5EB Manual de instrucciones
OPERATION & MAINTENANCE
INSTRUCTIONS
GC0513
DRILL PRESS
MODEL NO: CDP5EB/RB
PART NO: 655030 & 655035
2
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
INTRODUCTION
Thank you for purchasing this CLARKE Drill Press. These instructions cover the
CDP5EB (blue) and the CDP5RB (red).
Before attempting to use this product, please read this manual thoroughly and
follow the instructions carefully. In doing so you will ensure the safety of yourself
and that of others around you, and you can look forward to your purchase
giving you long and satisfactory service.
IMPORTANT
Please read all of the safety and operating instructions carefully before using
this product. Please pay particular attention to all sections of these instructions
that display warning symbols and notices.
GUARANTEE
This product is guaranteed against faulty manufacture for a period of 12
months from the date of purchase. Please keep your receipt which will be
required as proof of purchase.
This guarantee is invalid if the product is found to have been abused or
tampered with in any way, or not used for the purpose for which it was
intended.
Faulty goods should be returned to their place of purchase, no product can
be returned to us without prior permission.
This guarantee does not effect your statutory rights.
WARNING: THIS SYMBOL IS USED THROUGHOUT THE INSTRUCTIONS
WHENEVER THERE IS A RISK OF PERSONAL INJURY. ENSURE THAT
THESE WARNINGS ARE READ AND UNDERSTOOD AT ALL TIMES.
3
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
GENERAL SAFETY RULES
GENERAL SAFETY IN THE WORKPLACE
1. ALWAYS ensure that air can circulate around the machine and that the air
vents are unobstructed.
2. ALWAYS keep work area clean & tidy. Cluttered work areas and benches
invite accidents.
3. NEVER over-reach. Keep proper footing and balance at all times.
4. NEVER store equipment in a wet/damp environment or expose to rain.
5. KEEP other persons away. Do not let persons, especially children, not
involved in the work, touch the tool or extension cable and keep them
away from the work area.
6. NEVER operate a machine when under the influence of alcohol, drugs or
medication.
7. ALWAYS ensure the workplace is well lit. Ensure that lighting is placed so
that you will not be working in your own shadow.
8. Do not use tools in the presence of flammable liquids or gasses.
9. Stay alert, watch what you are doing, use common sense and do not
operate the tool when you are tired.
CARE OF POWER TOOLS
1. Read this manual carefully. Learn the machines applications and
limitations, as well as the specific potential hazards peculiar to it.
2. ALWAYS keep guards in place and in working order. A guard or other part
that is damaged should be properly repaired or replaced by an authorised
service centre, unless otherwise indicated in this instruction manual.
3. Remove any adjusting keys or wrenches before starting. Form the habit of
checking to ensure that keys, wrenches and tools are removed from the
machine.
4. Don’t force the machine and use the correct tool. It will do the job better
and safer, at the rate for which it was intended.
WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS
SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK AND PERSONNAL INJURY INCLUDING THE FOLLOWING. READ ALL
THESE INSTRUCTIONS BEFORE ATTEMPTING TO OPERATE THIS PRODUCT
AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
4
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
5. ALWAYS disconnect the machine from the power supply before carrying
out any servicing or changing of accessories.
6. Before further use of the tool, it should be carefully checked to determine
that it will operate properly and perform its intended function. Check for
alignment of moving parts, binding of moving parts, breakage of parts,
mounting or other condition that may affect its operation.
7. Have defective switches repaired by an authorised service centre. Do not
use a tool if the switch does not turn it on and off.
8. ALWAYS check for any damage or any condition that could affect the
operation of the machine. Damaged parts should be properly repaired.
9. NEVER remove the cover panel unless the machine is disconnected from
the power supply, and never use the machine with cover panels removed.
10. Have your tool repaired by a qualified person. This tool complies with the
relevant safety rules. Repairs should only be carried out by qualified
persons using original spare parts, otherwise this may result in considerable
danger to the user.
11. NEVER use this product for any other purpose than that described in this
booklet.
12. NEVER abuse the power cable by yanking the cable to disconnect it from
the socket. Keep the cable away from heat, oil or sharp edges.
13. Guard against electric shock. Avoid body contact with earthed or
grounded surfaces.
14. If the tool should be used outdoors, use only extension cables intended for
outdoor use and marked accordingly.
15. Avoid accidental starting by making sure the power switch is off before
plugging in the power cable.
ADDITIONAL SAFETY RULES FOR DRILL PRESSES
1. IMPORTANT: You should not operate this machine unless you are thoroughly
familiar with drilling machines and drilling techniques. If there is any doubt
whatsoever you should consult a qualified person.
2. NEVER operate the machine until it is completely assembled and you have
read and understood this entire manual.
CAUTION: AS WITH ALL MACHINERY, THERE ARE CERTAIN HAZARDS
INVOLVED WITH THEIR OPERATION AND USE. EXERCISING RESPECT AND
CAUTION WILL CONSIDERABLY LESSEN THE RISK OF PERSONAL INJURY.
HOWEVER, IF NORMAL SAFETY PRECAUTIONS ARE OVERLOOKED, OR
IGNORED, PERSONAL INJURY TO THE OPERATOR, OR DAMAGE TO
PROPERTY MAY RESULT.
5
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
3. ALWAYS use clamps or a drill vice bolted to the table, to hold the work. It
should never be held with bare hands.
4. ALWAYS shut off the power & remove drill bit before leaving the machine.
5. ALWAYS make all adjustments with the power off.
6. ALWAYS use the correct drilling speeds for the drill size and the type of
material being drilled.
7. NEVER leave the drill unattended whilst it is running. Turn the machine OFF
and do not leave until it has come to a complete stop.
8. ALWAYS remove and store the drill bits when you have finished work.
9. NEVER attempt to drill into a workpiece that does not have a flat surface
unless a suitable support is used.
10. ALWAYS stop the drill before removing workpieces, work supports or swarf
from the table.
11. Keep drills sharp and clean for best and safest performance. Follow
instructions for changing accessories.
12. Adjust the table or depth stop to avoid drilling into the table surface.
13. ALWAYS be sure that the drill bit is securely locked in the chuck.
14. NEVER assemble or set up any work on the table while the drill is running.
15. ALWAYS ensure the table lock is tight before starting the drill.
16. Keep handles dry, clean and free from oil and grease.
17. ALWAYS keep hands and fingers away from the drill bit.
PROTECTIVE CLOTHING
1. Dress properly. Loose clothing or other jewellery may get caught in moving
parts. Non-slip footwear is recommended. Wear protective hair covering to
contain long hair..
2. ALWAYS wear safety glasses. (Everyday glasses are not safety glasses.)
3. Wear a face mask if drilling into any material which produces dust.
WARNING: DUST GENERATED FROM CERTAIN MATERIALS CAN BE
HAZARDOUS TO YOUR HEALTH. ALWAYS OPERATE THE DRILL IN A WELL
VENTILATED AREA. USE A DUST COLLECTION SYSTEM IF POSSIBLE.
WARNING: THE USE OF ANY ACCESSORY OR ATTACHMENT OTHER THAN
ONE RECOMMENDED IN THIS INSTRUCTION MANUAL MAY PRESENT A RISK
OF PERSONNAL INJURY.
6
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
ELECTRICAL CONNECTIONS
Before switching the product on, make sure that the voltage of your electricity supply is
the same as that indicated on the rating plate. This product is designed to operate on
230VAC 50Hz. Connecting it to any other power source may cause damage.
This product may be fitted with a non-rewireable plug. If it is necessary to change the
fuse in the plug, the fuse cover must be refitted. If the fuse cover becomes lost or
damaged, the plug must not be used until a suitable replacement is obtained.
If the plug has to be changed because it is not suitable for your socket, or due to
damage, it should be cut off and a replacement fitted, following the wiring instructions
shown below. The old plug must be disposed of safely, as insertion into a mains socket
could cause an electrical hazard.
If the colours of the wires in the power cable of this product do not correspond with the
markings on the terminals of your plug, proceed as follows.
If the colours of the wires in the power cable of this product do not correspond with the
markings on the terminals of your plug, proceed as follows.
• The wire which is coloured Blue must be connected to the terminal which is
marked Nor coloured Black.
• The wire which is coloured Brown must be connected to the terminal which is
marked Lor coloured Red.
• The wire which is coloured Yellow and Green must be connected to the
terminal which is marked E or or coloured Green.
We strongly recommend that this machine is connected to the mains supply via a Residual
Current Device (RCD)
If in any doubt, consult a qualified electrician. DO NOT attempt any repairs yourself.
WARNING! Read these electrical safety instructions thoroughly
before connecting the product to the mains supply.
WARNING! The wires in the power cable of this product are
coloured in accordance with the following code:
Blue = Neutral Brown = Live Yellow and Green = Earth
Plug must be BS1363/A approved.
Always fit a 13 Amp fuse.
Ensure that the outer sheath of the cable is firmly held by the clamp
Neutral
(Blue)
Live
(Brown)
Earth
(Green and Yellow)
7
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
PRODUCT OVERVIEW
NO DESCRIPTION NO DESCRIPTION
1 Head & Motor Assembly 7 Chuck Key
2 Column 8 Feed Handles (x 3)
3Base 9Bolts(x3)
4 Table 10 Table Locking Handle
5 Chuck Guard Assembly 11 Depth Stop Assembly
6 Chuck 12 Hex Key
13
2
6
5
4
7
8
9
10
8
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
UNPACKING
The drill press is delivered with the components shown on page 7.
Check the parts against the above list. Should there be any deficiencies or
damage, you should contact your CLARKE dealer immediately where the
product was originally purchased. Do not discard the packaging until the
machine is assembled. The packaging consists of cardboard and
appropriately marked materials which can be sent tp a re-cycling facility.
To protect the machine parts from moisture, a protective coating of light
machine oil will have been applied to the outside surfaces. Remove any
excess with a paper towel.
Take care when lifting the head assembly, considering its weight.
Before use, the machine must be mounted, and securely bolted, to a strong,
heavy workbench, of sufficient height that you will be standing upright when
working.
Ensure the work place is adequately lit, and that you will not be working in your
own shadow.
ASSEMBLY
COLUMN TO BASE
Bolt the column assembly to the base with the three bolts provided.
NOTE: Ideally, the base with column attached, should be firmly bolted to
the workbench, prior to the assembly of other components.
TABLE TO COLUMN
1. Thread the table locking handle
into the table support from the
right hand side and leave it loose
at this stage.
2. Slide the table support with the
table, over the column, and allow
it to rest against the base as
shown in Fig.1.
9
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
HEAD TO COLUMN
NOTE: It may be necessary to
unscrew both the head
locking set screws
slightly, to ensure they do
not protrude internally,
as this would prevent the
head from sliding fully
into position.
1. Lift the head assembly and
locate it on top of the
column, ensuring it slides
home fully.
2. Align the head with the base, and
firmly secure to the column with
the set screws as shown in Fig. 2.
Tighten with the hex key supplied.
3. Screw the three feed handles,
firmly into the hub of the feed
shaft shown in Fig. 3.
CHUCK GUARD ASSEMBLY
This task should be carried out before
the chuck is installed.
1. Slide the chuck guard support
over the Quill Shaft and nip up the
pinch bolt at the rear of the
assembly shown in Fig 4.
2. Assemble the transparent guard
to the guard support using the
small bolt/nut and the two small
screws provided. (A small x-head
screwdriver will be required.)
10
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
ASSEMBLING THE DEPTH STOP
1. Slide the end of the threaded rod
through the bracket on the side of
the head and through the hole in
the top of the chuck guard
support as shown in Fig 5.
2. Secure with the nut provided,
from beneath, locking the Depth
Stop to the Chuck Guard and the
spindle assembly. (In use, as the
spindle is moved downwards, the
depth stop will move by the same
amount).
3. Add the two adjuster nuts to the
depth stop and slide the pointer
to the tip of the stop rod as shown
in Fig 6. The pointer may be
zeroed by sliding it up or down on
its mounting.
INSTALLING THE CHUCK
1. With the chuck guard lifted clear
of the spindle nose, slide the work
table up the column to within 6" of
the spindle.
2. Open the jaws of the chuck to
their maximum, using the chuck
key supplied.
3. Put a piece of scrap wood on the
table to protect the chuck nose
as shown in Fig 7.
4. Ensuring all parts are thoroughly clean, dry, and burr free, place the chuck
over the end of the spindle and pull the spindle down using the feed
handles, pressing the chuck jaws hard against the piece of scrap wood
until the chuck is forced home. Discard the scrap wood.
5. When the chuck is installed, turn the chuck guard around so that the shield
is facing the front, and tighten the pinch bolt to secure it in position.
Este manual sirve para los siguientes modelos
3
Tabla de contenidos
Otros manuales de Herramientas eléctricas de Clarke
Clarke
Clarke Air 25C Manual de instalación y operación
Clarke
Clarke CTC150 Manual de instrucciones
Clarke
Clarke CDP10B Manual de instrucciones
Clarke
Clarke CAT209 Manual de instalación y operación
Clarke
Clarke STRONG-ARM CSA12F Manual de instrucciones
Clarke
Clarke STRONG-ARM CSA4B Manual de instrucciones
Clarke
Clarke CPSB1 Manual de instrucciones
Clarke
Clarke Contractor CON750 Manual de instrucciones
Clarke
Clarke ECSS-1 Guía del usuario
Clarke
Clarke Woodworker CJS2 Manual de instalación y operación
Clarke
Clarke CAT21B Manual de instalación y operación
Clarke
Clarke X-Pro CAT205 Manual de instalación y operación
Clarke
Clarke X-Pro CAT199 Manual de instalación y operación
Clarke
Clarke Air CSG3KC Manual de instalación y operación
Clarke
Clarke Metalworker CDP301B Manual de instalación y operación
Clarke
Clarke STRONG-ARM CSA50FP Guía de solución de problemas
Clarke
Clarke COEBS1 Manual de instrucciones
Clarke
Clarke CAT55 Manual de instalación y operación
Clarke
Clarke STRONG-ARM CS4BRK Manual de instrucciones
Clarke
Clarke CAT221B Manual de instrucciones
