Clarke Air TPG30PTC Manual de usuario

USER INSTRUCTIONS

GC0516

TYRE INFLATOR

MODEL NO: TPG30PTC

PART NO: 3082107

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this CLARKE product. Before attempting to use this

product, please read this manual thoroughly and follow the instructions

carefully. In doing so you will ensure the safety of yourself and that of others

around you, and you can look forward to your purchase giving you long and

satisfactory service.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission. This guarantee does not effect your

statutory rights.

SPECIFICATION

GENERAL SAFETY PRECAUTIONS

1. Compressed air can be dangerous. Ensure that you are thoroughly familiar

with all precautions relating to the use of compressors and a compressed

air supply.

2. Never direct a jet of compressed air at people or animals.

3. Always ensure that the equipment/tool being used has a safe working

pressure exceeding the output pressure of the compressor that it is

connected to.

4. Never exceed the operating pressure stated in the specification.

5. Always ensure that the air supply is turned off at the tool outlet and vent all

compressed air from the air hose and the equipment attached to it, before

disconnecting air hoses or other equipment from your compressor.

Weight 0.65 kg

Connecting Hose Length 400 mm

Max Working Pressure 8 bar/ 116 psi

Airline Connection size 1/4” BSP

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

6. Ensure all fixed air connections are properly sealed using teflon tape or

pipe sealant.

7. Check the gauge periodically for accuracy and replace if damaged or

inaccurate.

OPERATION

Under or over inflated tyres are dangerous. Consult vehicle owners handbook

before using this tyre inflator.

Attach the airline hose to the tyre inflator and fully tighten. Use PTFE tape if

needed. Turn on the air supply and check that the airline pressure does not

exceed 8 bar (116psi)

1. Remove the dust cap from the tyre valve and check that the tyre valve is

clean before connecting.

2. Push the connector fully home onto the tyre valve. If the valve leaks, the

connector may need repositioning. Correct position is confirmed by a

steady reading on the gauge.

3. Check the tyre pressure on the gauge.

4. Pull the trigger to inflate the tyre. Re-check the tyre pressure. Note that

when the trigger is pulled, the gauge will show the airline pressure, not the

tyre pressure.

5. To deflate the tyre, partially pull the trigger and check the pressure again.

6. When the tyre pressure is correct, disconnect and remove the connector.

Replace the dust cap on the tyre valve.

IMPORTANT: The air pressure gauge on this product is for guidance only. It is

important that you check the pressure with an approved, calibrated

gauge.

7. Inspect the air hose for wear or damage periodically and replace if

necessary.

8. DO NOT use damaged or leaking hoses. Occasionally clean the product

and lubricate the trigger parts.

CAUTION: THIS PRODUCT MAY HAVE A LOWER WORKING PRESSURE

THAN SOME COMPRESSORS WILL SUPPLY, THEREFORE, AN AIRLINE

REGULATOR SHOULD BE INSTALLED.

CAUTION: AIRLINE LUBRICATORS SHOULD NOT BE USED WITH THIS ITEM

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Herramientas eléctricas de Clarke

Clarke

Clarke CHG1600 Manual de usuario

Clarke

Clarke CONTRACTOR CON800 Manual de instalación y operación

Clarke

Clarke Strong-Arm GC0915 Manual de instrucciones

Clarke

Clarke Metalworker CDP502F Manual de instrucciones

Clarke

Clarke STRONG-ARM CSA50FP Guía de solución de problemas

Clarke

Clarke CAT134 Manual de instalación y operación

Clarke

Clarke CWS250 Manual de instalación y operación

Clarke

Clarke CSB34 Manual de instrucciones

Clarke

Clarke Air CAT149 Manual de instalación y operación

Clarke

Clarke METALWORKER CBS20 Manual de usuario

Clarke

Clarke BJ300 Manual de usuario

Clarke

Clarke Strong-Arm AHP 26 Manual de instrucciones

Clarke

Clarke STRONG-ARM CSA10BB Manual de instrucciones

Clarke

Clarke METALWORKER CMPS1 Manual de instrucciones

Clarke

Clarke CAG120 Manual de instalación y operación

Clarke

Clarke CAT141 Manual de instalación y operación

Clarke

Clarke CAT21B Manual de instalación y operación

Clarke

Clarke CIWLI300 Manual de instalación y operación

Clarke

Clarke CE7 PRO Manual de usuario

Clarke

Clarke METALWORKER CDP401B Manual de instalación y operación

Clarke

Clarke CTIDG2 Manual de instrucciones

Clarke

Clarke 6505512 Manual de instrucciones

Clarke

Clarke Metalworker CDP101B Manual de instalación y operación

Clarke

Clarke CBM 2B Manual de instalación y operación

Manuales populares de Herramientas eléctricas de otras marcas

AEG

AEG OMNI-JS Manual de usuario

SIP

SIP 01533 Manual de usuario

Ribimex

Ribimex PRS499 Manual de usuario

3M Fiber Optic Connector Crimp Tool Manual de usuario

Ryobi

Ryobi P524 Manual de usuario

ROJEK

ROJEK FSN 300A Manual de usuario

Kemper

Kemper 1740PRO Manual de usuario

WABCO

WABCO OptiTire Manual de usuario

EINHELL

EINHELL TE-MS 18/210 Li Manual de usuario

Orgapack

Orgapack OR-T 85 Guía rápida

TOUGHCUT

TOUGHCUT Diamond 400 Manual de usuario

Yaros

Yaros PB-3603 Manual de usuario

Fein

Fein BSS 2.0 E Guía de configuración

Baileigh Industrial

Baileigh Industrial SS-2725 Manual de usuario

Milwaukee

Milwaukee 2674-20 Manual de usuario

Fein

Fein BLs 1.6 Manual de usuario

Princess

Princess Electric Multi Sharpener Manual de usuario

FOREDOM

FOREDOM K.1050 Manual