Clarke STRONG-ARM CTJ2B Manual de instrucciones
OPERATION & MAINTENANCE
INSTRUCTIONS
05/08
HYDRAULIC TROLLY JACK
MODEL NO: CTJ2B, CTJ2MB
PART NO: 7623035, 7623040
2
INTRODUCTION
Thank you for purchasing this CLARKE Hydraulic Trolly Jack
Before attempting to use this product, please read this manual thoroughly and
follow the instructions carefully. In doing so you will ensure the safety of yourself
and that of others around you, and you can look forward to your purchase
giving you long and satisfactory service.
GUARANTEE
This product is guaranteed against faulty manufacture for a period of 12
months from the date of purchase. Please keep your receipt which will be
required as proof of purchase.
This guarantee is invalid if the product is found to have been abused or
tampered with in any way, or not used for the purpose for which it was
intended.
Faulty goods should be returned to their place of purchase, no product can
be returned to us without prior permission.
This guarantee does not effect your statutory rights.
SPECIFICATIONS
Model number CTJ2B CTJ2MB
Part number 7623035 7623040
Length (not including handle): 452 mm 452 mm
Width 188 mm 188 mm
Height of lifting cup (at rest): 130 mm 130 mm
Maximum lifting height from floor: 338 mm 338 mm
Distance raised per stroke: 6.5 mm 6.5 mm
Weight 8.5 kg 8.5 kg
Number of full strokes to maximum height: 32 32
Rated capacity 2 Tonnes 2 Tonnes
3
SAFETY PRECAUTIONS
1. This jack is for lifting only, do not move a load using the jack as a dolly
2. Always inspect the jack before use. Make sure that all parts are in good
condition and operating smoothly, and that no cracks or distortion is
apparent. If in doubt do not use. Have the parts replaced or consult your
CLARKE dealer.
3. Make sure that the jack is on a firm solid base, and there is no possibility of it
slipping when under load.
4. Make sure the load is taken by the full saddle and that the point of lift on
the load, is of sufficient strength to support the full load adequately.
5. Always use supports to stabilise the load once lifted. NEVER work on or
under a load unless it is fully and adequately supported. NEVER rely upon
the jack to hold the load in position.
6. Never push a load off the jack.
7. Ensure that all personnel are well clear of a load being raised, or lowered.
8. NEVER exceed the rated load for the jack (See “Specifications” on
page 2.).
9. Do not use if an oil leak is apparent. Consult your Clarke dealer.
SPARE PARTS
The following user serviceable parts are available from your Clarke dealer, or
Clarke International Parts Department.
1. Saddle
2. Castor Assembly
3. Front Wheel Assembly
4. Operating Lever
5. Carrying Handle
4
OPERATION
NOTE: Where included, the carrying handle should be attached by
clipping it over the two large nuts at the main arm pivot. see
photograph on the front cover.
Ensure the load is chocked and stable and on firm level ground
1. Position the jack so that the saddle is directly beneath the lifting point and
that there are no obstacles to prevent a clean lift, also, make sure that all
personnel are well away from the area, before raising the vehicle.
• Consult the vehicle handbook to determine the correct lifting points.
USING THE TROLLEY JACK
1.
Release Valve
Place the operating lever over the
release valve and turn it fully
clockwise to close the valve.
2.
Jacking Port
Place the operating lever in the
jacking port and pump the
operating lever so that the saddle
rises to the lifting point.
• Raise the vehicle to the
required level.
3. Place axle stands directly
beneath suitable support points,
4. Place the operating lever over the release valve and VERY carefully turn
the handle anti-clockwise to lower the load on to the axle stands.
• Ensure the axle stands are centred about the support point and
perfectly stable before full weight is taken.
NOTE: Ensure this operation is carried out under complete control. DO
NOT allow the load to drop suddenly as this could damage
internal components.
5. Remove the jack from the vehicle.
NOTE: The jack will move slightly during operation. It is important
therefore that the immediate vicinity is clean and completely
free from debris.
5
MAINTENANCE
BEFORE USE.
Inspect for distortion of components, and security of all nuts and bolts. If in
doubt, do not use. Have damaged parts repaired or replaced. If necessary,
consult your CLARKE dealer.
EVERY 6 MONTHS
1. Oil all joints, linkages and front wheel hubs.
2. Apply grease to the caster bearings.
NOTE: Lubrication and cleanliness is important as dirt, rust etc can
cause a jerky action which could damage internal components.
ANNUALLY
Carry out a thorough inspection for serviceability of components & check for
oil leaks. Only a very slight oil seepage is permissible. If a leak is evident, do not
use jack and consult your CLARKE dealer.
STORAGE
Store in a dry place, with the ram fully retracted, where it cannot be
attacked by the elements. If stored for long periods, inspect at least once a
year, clean and re-oil. For servicing, contact your CLARKE dealer, or CLARKE
International Service Department.
For Spare Parts and Servicing, please contact your nearest dealer, or
CLARKE International, on one of the following numbers.
PARTS & SERVICE TEL: 020 8988 7400
PARTS & SERVICE FAX: 020 8558 3622
6
TROUBLESHOOTING
PROBLEM CAUSE SOLUTION
Jack Will Not
Raise The Load
Low Oil Level 1. Make sure the ram is fully retracted by turning the handle
fully anti-clockwise.
2. Turn the release valve fully anti-clockwise and remove it.
3. If necessary, top up to the required level
4. Only use clarke hydraulic oil (part no. 3050830 for a 1 litre
bottle.
5. Replace the release valve, closing it fully, then pump
handle until the arm reaches its full height.
6. Open release valve and step on saddle forcing it to lower
as quickly as possible. repeat this procedure three or four
times.
7. Finally, raise jack under load to test its operation.
Air In The System 1. Open release valve and pump handle fully, 6 or 7 times to
purge air.
2. Close release valve and try again.
Release Valve
Seat Dirty
1. Pull lifting arm up and down a few times with the release
valve open. if necessary, the valve may be removed and
the valve seat cleaned.
Jack Lowers
Under Load.
Discharge Valve
Held Open
1. Follow the procedure for “low oil level” above.
Release Valve
Held Open/dirty
1. Pull lifting arm up and down a few times with the release
valve open. if necessary, the valve may be removed and
the valve seat cleaned.
Jack Will Not Lift
Full 2 Tonne
Air May Be
Trapped In The
System
1. Open release valve and pump handle fully, 6 or 7 times to
purge air.
2. Close release valve and try again.
If any of these remedies fail to restore your jack, consult your CLARKE dealer
• The oil level should be level with the bottom of
the threads inside the oil chamber.
7
DECLARATION OF CONFORMITY
DECLARATION OF CONFORMITY
This is an important document and should be retained.
CTJ Trolley jack DOC- RV1.doc Page 1 of 1
We declare that this product complies with the following directives:
98/37/ EC Machinery Directive.
The Following Standards have been applied to the product:
The technical documentation required to demonstrate that the products meet the
requirements of the Machinery directive has been compiled and is available for inspection
by the relevant enforcement authorities.
The CE mark was first applied in: 2005
Product Description: 2 Ton Trolley Jack
Model number(s): CTJ2B
Serial / batch Number: Current Manufacture.
Date of Issue: 09-07-08
Signed
A.C.AIKEN
Senior Manager Clarke International.
DECLARATION OF CONFORMITY
This is an important document and should be retained.
CTJ2MB Trolley Jack DOC-RV1.doc Page 1 of 1
We declare that this product complies with the following directives:
98/37/ EC Machinery Directive.
The Following Standards have been applied to the product:
The technical documentation required to demonstrate that the products meet the
requirements of the Machinery directive has been compiled and is available for inspection
by the relevant enforcement authorities.
The CE mark was first applied in: 2005
Product Description: 2 Ton DIY Trolley Jack In Plastic Case
Model number(s): CTJ2MB
Serial / batch Number: Current Manufacture.
Date of Issue: 09-07-08
Signed
A.C.AIKEN
Senior Manager Clarke International.
Este manual sirve para los siguientes modelos
3
Tabla de contenidos
Otros manuales de Jacobo de Clarke
Clarke
Clarke Strong Arm CTJ3000GB Manual de instrucciones
Clarke
Clarke STRONG-ARM CTJ1250A Manual de usuario
Clarke
Clarke STRONG-ARM CTJ10GLB Manual de instrucciones
Clarke
Clarke CTJ30 Guía de solución de problemas
Clarke
Clarke Strong-Arm CTJ2GLS Manual de instrucciones
Clarke
Clarke STRONG-ARM CTJ3000G Manual de usuario
Clarke
Clarke STRONG-ARM CML3 Guía de referencia rápida
Clarke
Clarke STRONG-ARM VPJ300 Manual de usuario
Clarke
Clarke CBJ32 Manual de instrucciones
Clarke
Clarke CGK4 Manual de usuario
Clarke
Clarke STRONG-ARM CTJ3000G Manual de instrucciones
Clarke
Clarke STRONG-ARM CHDDWD Manual
Clarke
Clarke STRONG-ARM CTJ2GLC Manual de usuario
Clarke
Clarke Strong-Arm CTJ1500QULP Manual de instrucciones
Clarke
Clarke CTJ2000LP Manual de instrucciones
Clarke
Clarke CFJ48 Manual de instalación y operación
Clarke
Clarke STRONG-ARM CTJ3000QLB Manual de instrucciones
Clarke
Clarke Strong-Arm CTJ2250LP Manual de instrucciones
Clarke
Clarke Strong Arm CTJ1250AB Manual de instalación y operación
Clarke
Clarke CTJ1800AB Manual de instrucciones
