Clarke CTJ2000LP Manual de instrucciones

OPERATING & MAINTENANCE

INSTRUCTIONS GC01/12

2TONNE TROLLEY JACK

PART NO: 7623065

Model No: CTJ2000LP

Parts & Service: 020 8988 7400/E-mail:[email protected] or [email protected]

INTRODUCTION

Thank you for purchasing this CLARKE Trolley Jack.

Before attempting to use this product, please read this manual throughout

and follow the instructions carefully. Thoroughly familiarise yourself with this

product & its operation in order to ensure the safety of yourself and others

around you. In doing so, you can look forward to the product giving you

long and satisfactory service.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase. This guarantee is invalid if the product is found

to have been abused or tampered with in any way, or not used for it’s

intended purpose.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission. This guarantee does not effect

your statutory rights.

SPECIFICATION

Please note that details and specifications contained herein, are correct at

the time of going to print. However, CLARKE International reserve the right to

change specifications at any time without prior notice.

erutaeF noitacificepS

rebmuNtraP5603267

thgieWgk9.01

)HxWxL(snoisnemiDeldnahtuohtiwmm031x512x825

daoLdetaRennot2

elddaSfothgieHniMmm08

xaMelddaSfothgieHmm033

yticapaClIOlm501

thgieHxaMotniMmorfsekortSfooN43

ekortSrepdesiaRecnatsiD)egareva(mm3.

Parts & Service: 020 8988 7400/E-mail:Part[email protected] or [email protected]

GENERAL SAFETY PRECAUTIONS

GENERAL

1. ALWAYS read and ensure you fully understand the following precautions

and the hazards associated with this product. Do not allow anyone who

has not read these instructions to use the jack.

2. Only use this jack for its intended purpose.

3. NEVER carry out any modifications to this product. If experiencing difficulty

of any kind consult your local dealer.

WORK AREA

1. NEVER use the jack on sloping surfaces, only on level ground. The jack

may move away slightly as soon as it lifts the tyre from the ground.

2. DO NOT start the vehicle engine with the jack in use.

3. This jack is for lifting ONLY. DO NOT move a load using the jack as a dolly.

4. Ensure the load is taken by the full saddle and that the point of lift on the

load is of sufficient strength to support the full load adequately.

5. Never allow children or bystanders in the area while the jack is in use.

6. NEVER work underneath a vehicle supported only by this product. If

working under a vehicle, always use stands designed for the purpose.

7. Ensure the jack is on a firm solid base and that there is no likelihood of it

slipping when under load.

8. Ensure that all personnel are well clear of a load being raised or lowered.

SERVICING & REPAIRS

1. Check the jack for damage before use and do not use if damaged. If in

doubt, DO NOT use. Consult your local dealer.

2. ALWAYS use spare parts supplied by Clarke International. Using non-

standard parts could be extremely dangerous.

3. Ensure the jack is properly maintained at all times and that no damage is

allowed to weaken any part of it. Do not use if an oil leak is apparent.

4. When necessary, have your jack serviced or repaired by a qualified

technician using identical replacement parts. This will ensure that the

safety of the jack is maintained.

5. NEVER exceed the rated load or use the jack if it has been subjected to

excess load (over 2 tonne). The jack should be removed from service

immediately and fully inspected by qualified personnel and passed as

serviceable before further use.

Please keep these instructions in a safe place for future reference.

Parts & Service: 020 8988 7400/E-mail:[email protected] or [email protected]

OPERATION

Before use, visually inspect the jack for oil leaks or any other sign of damage.

Should any be apparent, have the jack inspected and repaired by a

qualified technician before use.

WARNING! NEVER WORK ON THE VEHICLE WHEN SUPPORTED ONLY BY A

JACK. THIS IS A HIGHLY DANGEROUS PRACTICE. THE VEHICLE MUST BE

SUPPORTED ON AXLE STANDS, OR SUITABLE SUPPORTS, BENEATH THE

JACKING/SUPPORT POINTS RECOMMENDED BY THE VEHICLE

MANUFACTURER. THERE SHOULD BE NO LOAD ON THE JACK.

1. Ensure the vehicle to be raised is chocked, stable & on firm level ground

with the supporting wheels adequately chocked.

2. Position the jack so that the saddle is directly beneath the lifting point.

• Consult the vehicle handbook to determine suitable lifting points.

3. Place the handle over the control valve & turn clockwise to shut the valve

4. Insert the handle into the handle

sleeve and pump the handle to

raise the saddle until it reaches

the vehicle lifting point.

5. Take care that there are no

obstructions to prevent a clean

lift. Keep all personnel at a safe

distance before pumping the

handle to raise the vehicle.

NOTE: The jack may move slightly

during operation. It is important therefore, that the floor is clean

and completely free from debris.

6. Position axle stands directly beneath suitable supporting points below the

vehicle, before engaging the handle with the control valve and very

gently twisting the handle anticlockwise.

• This will open the control valve to lower the load onto the stands.

7. To stop it lowering, turn the handle clockwise again. Always avoid a rapid

descent by turning the handle slowly.

8. Carefully lower the vehicle onto the axle stand, checking constantly,

preferably with an assistant, that the vehicles supporting point rests snugly

and cleanly on the stand, and that the supporting stand is stable before

all the weight is taken.

NOTE: Ensure this operation is carried out under complete control. DO NOT

allow the load to drop suddenly as this could damage internal parts.

9. Completely remove the jack from the vehicle.

Control

Valve

Handle

Sleeve

Parts & Service: 020 8988 7400/E-mail:Part[email protected] or [email protected]

MAINTENANCE

PURGING AIR FROM THE SYSTEM

If air bubbles become trapped inside the hydraulic system, the efficiency of

the jack will be reduced. Any air can be purged from the system as follows.

1. Turn the control valve counter-clockwise and remove the filler plug.

2. Pump the handle several times to purge air from the system.

3. Replace the filler plug, then turn the control valve clockwise and test the

jack. If efficiency is still low, check the oil level as below.

CHECKING THE OIL LEVEL

If the jack has been stored for long periods, check for oil leaks before use. If

necessary, check the oil level as follows:

1. Ensure the jack is fully lowered by using the handle to turn the control

valve fully anticlockwise.

2. Lift up the cover plate and remove the oil filler plug on the top of the ram

assembly. A large cross headed screwdriver is required.

• The oil should be almost level with the bottom of the oil filler hole.

• Oil can be topped up using Clarke Hydraulic Oil (p/no 3050830 for 1 litre).

OIL REPLACEMENT

1. With the jack lowered, remove the filler plug. Tilt the jack onto its side and

drain the old oil into a container.

2. Return the jack to upright and refill with hydraulic oil up to the lower rim of

the filler hole.

3. Purge any air from the system and replace the filler plug.

4. Dispose of old oil appropriately and be sure to wipe up any spillage.

GENERAL CARE

1. Periodically lubricate the hinges, front wheels & rear castors with light oil.

2. Store in a dry location with the arm in its lowest position.

3. In the event of damage or broken components, replacements are

available from Clarke Parts & Service.

Parts & Service: 020 8988 7400/E-mail:[email protected] or [email protected]

TROUBLESHOOTING

MELBORP ESUAC NOITULOS

ehtotesiartonlliwkcaJ

.thgiehlluf

.levelliowoLfipupotdnaegakaelrofkcehC

.gulplioehtaivderiuqer

.metsysniriApmupdnagulprellifevomeR

metsysmorfriaegrupoteldnah

.5egapnodebircsedsa

.nrowsgnir-OrofrelaedekralCruoyotn

ruteR

.luahrevo

ehtdlohtonlliwkcaJ

.daol

tonevlavesaeleR

.desolcylthgit

.yllufgnisolcsievlavkcehC

tonevlaves

aeleR

.gnitaes

rofrelaedekralCruoyotnruteR

.luahrevo

.metsysniriApmupdnagulprellifevomeR

metsysmorfriaegrup

oteldnah

.5egapnodebircsedsa

rewoltonseodkcaJ

.denepoevlavnehw

dellif-revorednilyC

.liohtiw

.lioevissecxeffoniarD

mratovipronotsiP

.gnidnibrotneb

rofrelaedekralCruoyotnruteR

.riaper

rodetcennocsiD

.gnirpsnruterneko

rofrelaedekralCruoyotnruteR

.riaper

stnenopmocdegniH

.yleerfgnivomton

.stniojdegnihetacirbuL

nehwygnopss

leefkcaJ

.gnitfil

.metsysnideppartriApmupdnagulprellifevomeR

metsysmorfriaegrupoteldnah

.5egapnodebircseds

ENVIRONMENTAL PROTECTION

One of the most damaging sources of environmental pollution is oil

products. Never throw away used hydraulic oil with domestic refuse or

flush it down a sink or drain. Collect all the hydraulic oil in a leak proof

container and take it to your local waste disposal site.

Parts & Service: 020 8988 7400/E-mail:Part[email protected] or [email protected]

DECLARATION OF CONFORMITY

Parts & Service: 020 8988 7400/E-mail:[email protected] or [email protected]

COMPONENT PARTS

oN tsiLstraP oNtraP oN noitpircseD oNtraP

121MtuN10PL0002JTCAT7toviPmrAgnitfiL70PL0002JTCAT

2rehsaWtalF20PL0002JTCAT8pilCgniniateR80PL0002JTCAT

3leehW

tnorF30PL0002JTCAT9 emarFdnah-thgiR90PL0002JTCAT

4elxAtnorF40PL0002JTCAT01doRgnitcennoC01PL0002JTCAT

5emarFdnah-tfeL50PL0002JTCAT11spilCmrA11PL0002JTCAT

621oNrehsaWgnirpS60PL0002JTCAT21ecaRllaB21PL0002JTCAT

Parts & Service: 020 8988 7400/E-mail:Part[email protected] or [email protected]

oN tsiLstraP oNtraP oN noitpircseD oNtraP

31rotsaCraeR31PL0002JTCAT04laeS-U04PL0002JTCAT

418MtuN41PL0002JTCAT14rednilyCpmuP14PL0002JTCAT

51mm8rehsaWgn

irpS51PL0002JTCAT24rehsaW24PL0002JTCAT

61niPgnitcennoCmaR61PL0002JTCAT34llaBleetS34PL0002JTCAT

71pilcriC71PL0002JT

CAT44wercSevlaVlortnoC44PL0002JTCAT

81elxAniaM81PL0002JTCAT543x6gniR-O54PL0002JTCAT

91eldnaHgniyrraC91PL0002JTCAT6

4gePevlaVlortnoC64PL0002JTCAT

02ylbmessAmaR02PL0002JTCAT74paCevlaVytefaS74PL0002JTCAT

12gnirpSnruteR12PL0002JTCA

T84wercSevlaVytefaS84PL0002JTCAT

22mrAgnitfiL22PL0002JTCAT94gnirpSevlaVytefaS94PL0002JTCAT

32elddaS32PL0002JTCAT05r

egnulPevlaVytefaS05PL0002JTCAT

42pilcriC42PL0002JTCAT15mm4llaBleetS15PL0002JTCAT

52toviPelddaS52PL0002JTCAT25gnit

saCydoBmaR25PL0002JTCAT

62etalPrevoC62PL0002JTCAT35rehsaWnolyN35PL0002JTCAT

72doReiT72PL0002JTCAT45rehsaWmaR45PL00

02JTCAT

82eldnaHgnitarepO82PL0002JTCAT55rednilyCmaR55PL0002JTCAT

92niPtoviPrewoL92PL0002JTCAT65riovreseRliO65PL00

02JTCAT

03rehsaW03PL0002JTCAT75paCrelliFliO75PL0002JTCAT

13tuN13PL0002JTCAT85laeS-U85PL0002JTCAT

23gnitnuoMeldnaH23P

L0002JTCAT95reniateRgniR-O95PL0002JTCAT

33egniHnotsiPpmuP33PL0002JTCAT06gniRgniruceS06PL0002JTCAT

43niPgnitnuoMe

ldnaH43PL0002JTCAT16notsiPmaR16PL0002JTCAT

53niPtilpS53PL0002JTCAT26rehsaWnolyN26PL0002JTCAT

63pilCgnixiFnotsiP63P

L0002JTCAT36paCdnEriovreseR36PL0002JTCAT

73notsiPpmuP73PL0002JTCAT463x7.12gniR-O46PL0002JTCAT

839.1x8.7gniR-O83PL

0002JTCAT56"61/3llaBleetS56PL0002JTCAT

93gniRpu-kcaB93PL0002JTCAT---tiKlaeSciluardyH66PL0002JTCAT

COMPONENT PARTS

Parts & Service: 020 8988 7400/E-mail:[email protected] or [email protected]

COMPONENT PARTS

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Jacobo de Clarke

Clarke

Clarke Strong-Arm CFT5 Guía

Clarke

Clarke Strong-Arm CTJ2CBB Manual de instrucciones

Clarke

Clarke CTJ2000LPB Manual de instrucciones

Clarke

Clarke Strong Arm CTJ1250AB Manual de instalación y operación

Clarke

Clarke STRONG-ARM CTJ5GLB Manual de instrucciones

Clarke

Clarke STRONG-ARM CTJ2LP Manual de instrucciones

Clarke

Clarke CTJ1250AC Manual de instrucciones

Clarke

Clarke STRONG-ARM CTJ3GLC Manual de usuario

Clarke

Clarke Strong-Arm CTJ1500QULP Manual de instalación y operación

Clarke

Clarke CTJ2500QLG Manual de instalación y operación

Clarke

Clarke Strong-Arm CTJ100 Manual de instalación y operación

Clarke

Clarke STRONG-ARM CTJ3000QLB Manual de instrucciones

Clarke

Clarke STRONG-ARM CTJ1250A Manual de usuario

Clarke

Clarke CSJ1500 Manual de usuario

Clarke

Clarke STRONG-ARM CTJ2500QLGB Manual de instalación y operación

Clarke

Clarke CTJ2001G Manual de instrucciones

Clarke

Clarke CGK4 Manual de usuario

Clarke

Clarke CFJ60 Manual de usuario

Clarke

Clarke CTJ1800AB Manual de instrucciones

Clarke

Clarke CTJ1800A Manual de instrucciones

Clarke

Clarke STRONG-ARM CTJ2QLP Manual de instrucciones

Clarke

Clarke CTJ3QLGB Manual de instrucciones

Clarke

Clarke CFJ48 Manual de instalación y operación

Clarke

Clarke STRONG-ARM CTJ10GLB Manual de instrucciones

Manuales populares de Jacobo de otras marcas

Omega Lift Equipment

Omega Lift Equipment 18122C Instrucciones de uso

Pittsburgh

Pittsburgh 58816 Instrucciones de montaje

Unimec

Unimec TP Manual de usuario

Sonic

Sonic 4800703 Manual de usuario

BGS technic

BGS technic 70039 Manual de usuario

TradeQuip

TradeQuip 1128T Manual de usuario

VEVOR

VEVOR TJD-12000SP-F Manual de usuario

ULTIMATE SPEED

ULTIMATE SPEED URW 2 A1 HYDRAULIC TROLLEY JACK Manual de usuario

Stels

Stels 51131 Manual de usuario

Bushranger

Bushranger RJX01 Manual de usuario

Valex

Valex 1650520 Manual de usuario

Pfaff

Pfaff Merkur M0 Manual de usuario

Beta

Beta 3050/K Suplemento

Sealey

Sealey 1050CXHV Manual de usuario

Jung

Jung JH Series Manual de usuario

URIAH

URIAH UC200020 Manual de usuario

Kennedy

Kennedy KSJ010 Manual de usuario

Grizzly

Grizzly H8097 Manual de usuario