Clarke ETC180 Guía de referencia rápida

ASSEMBLY & OPERATING

INSTRUCTIONS

Model Nos ETC180

Part No: 3400740

GC05/14

ELECTRIC TILE CUTTER

INTRODUCTION

Thank you for purchasing this CLARKE product.

Please read this manual thoroughly and follow the instructions carefully and

follow the instructions given. In doing so you will ensure the safety of yourself

and that of others around you, and you can look forward to the product

giving you long and satisfactory service.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission.

This guarantee does not effect your statutory rights.

SAFETY PRECAUTIONS

WORK AREA

1. ALWAYS keep the work area clean and well lit. Floors should always be

kept clear. Cluttered or dark areas invite accidents.

2. ALWAYS keep children away and keep visitors at a safe distance from the

work area, especially whilst operating the machine.

3. ALWAYS place the machine on a firm steady base and at a comfortable

working height.

4. ALWAYS check to ensure that all other parts of the machine and the

surrounding work area are kept dry, apart from the water trough which is

provided to wet the cutting disc.

5. ALWAYS use in a well ventilated area. Never operate the cutter in the

presence of flammable vapours.

PERSONAL SAFETY

1. ALWAYS stay alert, watch what you are doing and use common sense

when operating a power tool. Do not use the machine while you are tired

or under the influence of medication, drugs or alcohol.

2. NEVER over-reach. Keep your proper footing and balance at all times to

enable better control of the machine in unexpected situations.

3. ALWAYS wear safety goggles, manufactured to the latest European Safety

Standards. Everyday eyeglasses do not have impact resistant lenses and

are not safety glasses.

4. ALWAYS concentrate on the job in hand, no matter how trivial it may

seem. Accidents are caused by carelessness due to familiarity.

5. ALWAYS keep your proper footing and balance at all times. For best

footing, wear rubber soled shoes. Keep floor clear of oil, scrap wood, etc.

6. ALWAYS use a face mask to prevent inhalation of dust.

7. ALWAYS take precautions in respect of loose clothing, jewellery & long hair,

which are potential hazards which could get caught in the cutting disc.

GENERAL USE AND CARE

1. ALWAYS ensure that the cutter cannot be started inadvertently by using

the ON/OFF switch whenever carrying out maintenance.

2. ALWAYS maintain in top condition. Keep clean for the best and safest

performance. Follow maintenance instructions.

3. ALWAYS check for damage or condition that may affect the machine’s

operation. Any damage should be properly repaired or the part replaced.

If in doubt, DO NOT use the machine. Consult your Clarke dealer.

4. ALWAYS keep the mains cable well away from any machinery and ensure

an adequate electrical supply is close to hand so that the operation is not

restricted by the length of cable.

6. NEVER drag the machine by its power cable or pull the cable to

disconnect it from the power supply.

7. ALWAYS ensure the switch is off before plugging into the power supply.

8. ALWAYS examine the cutting disc before use, and replace if badly worn.

9. ALWAYS allow the motor freedom, so that the cutting disc will be cutting

at, or close to its maximum speed.

10. ALWAYS turn off the power supply before making any adjustments.

11. NEVER force the cutting disc if it is reluctant to cut properly or slows down.

12. NEVER use this machine for cutting metal or timber. This machine is for

cutting stone, ceramics, marble and similar hard material ONLY.

13. NEVER apply side thrust to the cutting disc. i.e. try to cut on one side of the

disc only.

14. NEVER operate this machine with the blade guard removed.

15. ALWAYS store out of reach of children and do not allow persons unfamiliar

with these instructions to operate this machine.

16. NEVER attempt to repair the mains cable. If the cable, or any part of the

switch assembly becomes damaged it must be replaced.

ELECTRICAL CONNECTIONS

This product is provided with a 13 amp BS 1363 plug, fitted with a 13amp fuse and

MUST be connected to a standard, 230 Volt (50Hz) electrical supply, preferably

through an approved plug, or a suitably fused isolator switch.

WARNING: THIS APPLIANCE MUST BE EARTHED

IMPORTANT: The wires in the mains lead should be connected in accordance

with the following colour code:

Green & Yellow - Earth

Blue - Neutral

Brown - Live

As the colours of the flexible cable of this appliance may not correspond with

the coloured markings identifying terminals in your plug, proceed as follows:

•

Connect the GREEN & YELLOW coloured cord to the plug

terminal marked with a letter E or Earth symbol “ ” or

coloured GREEN or GREEN & YELLOW.

• Connect the BROWN coloured cord to the plug terminal

marked a letter “L” or coloured RED.

•

Connect the BLUE coloured cord to the plug terminal marked

a letter “N” or coloured BLACK

If this appliance is found to be fitted with a plug which is moulded on to the

electric cable (i.e. non-rewireable) please note:

1. The plug must be thrown away if it is cut from the electric cable. There is a

danger of electric shock if it is subsequently inserted into a socket outlet.

2. Never use the plug without the fuse cover fitted.

3. Should you wish to replace a detachable fuse carrier, ensure that the

correct replacement is used (as indicated by marking or colour code).

4. Replacement fuse covers can be obtained from your local Clarke dealer

or most electrical stockists.

FUSE RATING

The fuse in the plug must be replaced with one of the same rating and this

replacement must be ASTA approved to BS1362.

We strongly recommend that this machine is connected to the mains supply

via a Residual Current Device (RCD).

UNPACKING

When unpacking please check contents and advise your dealer immediately

if any parts are missing. The essential parts of the machine are as follows;

1. ETC180 Tile Cutter

2. Open Spanner

3. Special Spanner

4. Mitre Guide

5. Blade Guard Arm

6. Guard Bracket

7. Water Tray

8. Instruction Manual (this document)

All item numbers in the following text refer to the diagram on page 9.

ASSEMBLY

Although the machine is portable, always ensure its temporary working

location is flat and even, and at a convenient height with adequate lighting.

The machine is supplied

fully assembled, other than

the blade guard, which

must be fitted as follows:

1. Insert screws (45)

through the gap in the

table top (7) and screw

the guard support

bracket into frame (25)

below.

2. Attach the blade guard (4) to the bracket (5) by screwing the guard

securing knob (6) through the holes and into the captive nut (1) in the

guard.

OPERATION

1. Measure the tile or piece of material to be cut and proceed to adjust:

A) The angle of the table, which can be adjusted up to 45 degrees

from the horizontal for mitre edge cuts if required. For normal

perpendicular cuts, the table should be set to zero degrees on the

bevel scale.

B) The position of the fence on the table top. To ensure accurate cuts,

check the alignment of the fence by reference to the calibrated

scale, set into each end of the table top.

2. Re-tighten all locking knobs securely to ensure secure positions for both

the table top and the fence.

3. Fill the water trough (43) located underneath the table with just sufficient

water so that the edge of the cutting disc can be kept constantly wet. Do

not overfill as this can cause an unnecessary mess. Check the water level

constantly during use and top up as necessary. A filling hole (A), which

can accommodate, for example, a small watering can, is be found in the

front face of the machine frame.

4. Adjust the blade guard position, ensuring that there is sufficient room for

the tile to pass between the table top and the guard. The guard should

be parallel to the surface of the table with the minimum clearance

between the guard and the tile.

5. Start the machine by pressing the green button on the ON/OFF switch

(39), marked ‘I’.

6. Hold the material firmly at all times against the parallel fence, or hold it in

the mitre gauge, as required. Move it steadily over the table, into the

cutting edge of the disc.

7. DO NOT force the cutting disc through the tile. Keep the speed of the disc

as near to its maximum speed as possible.

8. Always cut in a straight line. DO NOT attempt to cut a curved line.

9. Keep hands well clear of the disc whilst it is in motion. Remove all pieces

using a piece of wood, or similar, before making the next cut.

10. To stop the machine at any time, press the red stop button marked ‘O’.

Always do this as soon as cutting has been completed, and before

making any adjustments to the machine.

NOTE:

Bevel cuts are usually made on the right side of the cutting disc,

i.e. on the ‘downward’ slope side of the disc, so that the glazed

side of the tile is uppermost, and as there is little room here for the

parallel fence, this operation is usually carried out freehand. DO

NOT exert side pressure on the cutting disc.

NOTE: In order to get the feel of the machine and reduce the possibility

of wastage, we recommend that trial cuts are made first with

surplus or scrap material of a similar type to that to be cut.

CHANGING THE CUTTING DISC

1. Ensure that the machine is switched off and disconnected from the mains.

2. First remove the water trough, then remove the two screws securing the

cutting disc cover, beneath the table, and withdraw the cover.

3. Undo the disc securing nut (21)

using the spanner supplied.

The drive shaft has two flats

milled on its end, allowing a

second spanner (supplied) to

be used to restrain the shaft

from rotating.

4. Pull off the clamping disc,(22)

followed by the cutting disc

(23).

5. Take this opportunity to clean

the drive-shaft of any foreign

matter.

6. Replace the cutting disc,

ensuring the direction of

rotation is correct. If in

doubt, take note that the shaft

rotates in an anticlockwise

direction as you look directly at

it. The disc must be fitted so that

the arrow on the cutting disc,

points in the SAME direction.

7. Replace the clamping plate and the nut. It is sufficient that the nut be

tightened only as much as is possible whilst holding the disc by hand. DO

NOT overtighten.

MAINTENANCE

When carrying out servicing or maintenance tasks...ALWAYS disconnect the

machine from the mains supply.

Always rotate the cutting disc by hand before use, to check for cracks or

distortion. If any damage is detected, renew the disc.

Check the power cable to ensure it is in perfect condition.

Drain the water tank after use and ensure it is dry before storing.

ALWAYS maintain the machine in top condition. When not in use, keep it

covered, and store in a dry place, not exposed to the elements.

SPECIFICATION

Motor ....................................................................................... 230V, 50 Hz 1ph

Power Rating .......................................................................... 500 Watts

Speed ...................................................................................... 2800 RPM

Fuse Rating .............................................................................. 13 Amps

Weight (net) ............................................................................ 16 kg

Cutting Angle ......................................................................... 0 - 45 degrees

Cutting Depth at 90O............................................................ 33 mm

Cutting Depth at 45O............................................................. 24 mm

Cutting Disc Diameter ........................................................... 180 mm

Cutting Disc Bore .................................................................... 22.2 mm

Cutting Disc Part Number ..................................................... 6490640

Sound Power Level ................................................................ 104 Lw(A)

Sound Pressure Level ............................................................. <70 dB(A)

Vibration .................................................................................. <2.5m/s2

Table Dimensions .................................................................... 420x400 mm

Overall Dimensions (LxWxH) .................................................. 460x420x295 mm

ENVIRONMENTAL PROTECTION

Do not dispose of this product with general household waste. This product

contains valuable raw materials and should be disposed of appropriately at a

recognised disposal facility.

COMPONENT PARTS

Through purchase of this product, the customer is taking on the obliga-

tion to deal with the WEEE in accordance with the WEEE regulations in

relation to the treatment, recycling & recovery and environmentally

sound disposal of the WEEE.

In effect, this means that this product must not be disposed of with general

household waste. It must be disposed of according to the laws governing

Waste Electrical and Electronic Equipment (WEEE) at a recognised disposal

facility.

COMPONENT PARTS

oN noitpircseD oN noitpircseD

1tuN42csiDgnipmalCraeR

2a/n52emarFesaB

3a/n62bonKtnemtsujdAelbaT

4drauG72a/n

5tekcarBdrauG82a/n

6bonKgniruceSdr

auG92a/n

7poTelbaT03)01x6M(tloBegniH

8eldnaH13a/n

9paCcitsalP23rotoMevirD

01)HL(tekcarBediuGecneF33revoCevirD

11ecneF43werc

21)HR(tekcarBediuGecneF53roticapaC

31)8x5M(wercS63dnalGelbaC

41)61x6M(tloBhcaoC73pmalCelbaC

518MrehsaW83gulP&elbaC

1a/n93hctiwSFFO/NO

71bonKgniruceSecneF04)4M(wercS

81)6x4M(wercS14etalPhctiwS

91)4M(rehsaW24teeFrebbuR

02revoCevitcetor

P34knaTretaW

12)21M(tuN44)ylnosledomylrae(elacS

22csiDgnipmalCtnorF54)8x4M(wercS

32)0460946ontrap(csiDgnittuC

Note: All spare parts for ths product carry the prefix HT-ETC-180.

Otros manuales para ETC180

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cortador de Clarke

Clarke

Clarke 20CI Manual de instrucciones

Clarke

Clarke CAT127 Manual de instalación y operación

Clarke

Clarke TCM420 Manual de usuario

Clarke

Clarke ETC400 Guía de solución de problemas

Clarke

Clarke CMB710 Manual de instrucciones

Clarke

Clarke 30SI Manual de instalación y operación

Clarke

Clarke CHT532 Manual de usuario

Clarke

Clarke 1801518 Manual de usuario

Clarke

Clarke WE6493A Manual de usuario

Clarke

Clarke ETC8 Manual de instrucciones

Clarke

Clarke CHT518 Manual de usuario

Clarke

Clarke ETC6 Manual de instalación y operación

Clarke

Clarke CLC1 Manual de usuario

Clarke

Clarke ETC180 Manual

Clarke

Clarke Strong-Arm CS10HC Manual de instalación y operación

Clarke

Clarke TCM430 Manual de usuario

Clarke

Clarke X-Pro CAT203 Manual de instalación y operación

Clarke

Clarke ETC7 Manual de instalación y operación

Clarke

Clarke ETC8 Manual de instrucciones

Manuales populares de Cortador de otras marcas

Milwaukee

Milwaukee HEAVY DUTY M12 FCOT Manual de usuario

Makita

Makita DCS552 Manual de usuario

SignWarehouse.com

SignWarehouse.com Bobcat BA-60 Manual de usuario

Makita

Makita 4112HS Manual de usuario

GEISMAR STUMEC

GEISMAR STUMEC MTZ 350S Manual de usuario

Hitachi

Hitachi CM 4SB2 Guía de solución de problemas

Dexter Laundry

Dexter Laundry 800ETC1-20030.1 Manual de usuario

GCC Technologies

GCC Technologies AFJ-24S Manual de usuario

DeWalt

DeWalt XR LI-ION DCS350N Manual de usuario

Baudat

Baudat ES1 Manual de usuario

Mafell

Mafell ZAF 200 Guía

Makita

Makita 4100NH Manual de usuario

Formax

Formax FD 574 Manual de usuario

EINHELL

EINHELL TE-MA 1500 Manual de usuario

Husqvarna

Husqvarna Cut-n-Break K 760 Manual de usuario

CLEAN ROOM DEVICES

CLEAN ROOM DEVICES CRD130SS Manual de usuario

TRI tool

TRI tool 301A Manual de usuario

Roller

Roller King 1 1/4 Manual de usuario