Clarion ARX850z Manual de usuario

-1- ARX8570z

Published by Service Dept.

Printed in Japan

Clarion Co., Ltd.

ExportDivision-22-3,Shibuya2-chome,Shibuyaku,Tokyo,150-8335Japan Tel:03-3400-1121

ServiceDept.-50kamitoda,Toda-shi,Saitama,335-8511Japan Tel:048-443-1111 FAX:048-433-6996 298-5718-00 Jan.1999 P

Service Manual

Model

AM/FM Cassette Player with

CD/MD Changer Control

(PE-1637B)

■SPECIFICATIONS

FM tuner

Frequency range: 87.9MHz to 107.9MHz

Usable sensitivity: 11dBf

50dB quieting sensitivity:

17dBf

Alternate channel selectivity:

75dB

Stereo separation(1kHz):

35dB

Frequency response(±3dB):

30Hz to 15kHz

AM tuner

Frequency range: 530kHz to 1710kHz

Usable sensitivity: 25μV

Tape deck

Wow & flutter(WRMS): 0.06%

Channel separation(1kHz):

45dB

Frequency response(±3dB):

120μs(Normal)

30Hz to 18kHz

70μs(CrO2,FeCr,Metal)

30Hz to 20kHz

S/N ratio: 70μs(CrO2,FeCr,Metal)

Dolby NR off 58dB

Dolby B NR 67dB

Dolby C NR 74dB

Audio

Maximum power output:

180W(45W×4ch)(EIAJ)

Continuous average power output:

17W×4,into 4Ω,

20Hz to 20kHz,1%THD

Bass control action(30Hz):

±15dB

Treble control action(10kHz):

±10dB

Line output level(0VU tape):

1.6V

General

Power supply voltage: 14.4V DC(10.8 to 15.6V allowable)

negative ground

Current consumption: Less than 15A

Speaker impedance: 4Ω(4Ωto 8Ωallowable)

Dimensions(mm): Source unit

178(W)×50(H)×155(D)

Remote control unit

44(W)×110(H)×27(D)

Weight: Source unit 1.6kg

Remote control unit

30g(including battery)

※Dolby noise reduction manufactured under license from

Dolby Laboratories Licensing Corporation

Dolby and the double-D symbol are trademarks of Dolby

Laboratories Licensing Corporation.

※Specifications and design are subject to change with-

out notice for further improvement.

■NOTE

※We cannot supply PWB with component parts in prin-

ciple. When a circuit on PWB has failure , please repair

it by component parts base. Parts which are not men-

tioned in service manual are not supplied.

■COMPONENTS

PE-1637B-A

Main unit −−−−− 1

-2-

ARX8570z

■To engineers in charge of repair

or inspection of our products.

Before repair or inspection, make sure to follow

the instructions so that customers and Engineers

in charge of repair or inspection can avoid suf-

fering any risk or injury.

1. Use specified parts.

The system uses parts with special safety features

against fire and voltage. Use only parts with equivalent

characteristics when replacing them.

The use of unspecified parts shall be regarded as re-

modeling for which we shall not be liable. The onus of

product liability (PL) shall not be our responsibility in

cases where an accident or failure is as a result of un-

specified parts being used.

2. Place the parts and wiring back in their original positions

after replacement or re-wiring.

For proper circuit construction, use of insulation tubes,

bonding,gaps to PWB, etc, is involved. The wiring con-

nection and routing to the PWB are specially planned

using clamps to keep away from heated and high volt-

age parts. Ensure that they are placed back in their origi-

nal positions after repair or inspection.

Remote control RCB-130-600 1

Battery(SUM-3) −−−−− 2

Mounting bracket 300-7742-00 1

DCP case 335-6035-20 1

Outer escutcheon 370-5771-00 1

Extension lead 854-6349-50 1

Parts bag −−−−−

Removal tool 331-2497-00 2

Screw 716-0496-01 1

If extended damage is caused due to negligence during

repair, the legal responsibility shall be with the repairing

company.

3. Check for safety after repair.

Check that the screws, parts and wires are put back se-

curely in their original position after repair. Ensure for

safety reasons there is no possibility of secondary

ploblems around the repaired spots.

If extended damage is caused due to negligence of re-

pair, the legal responsibility shall be with the repairing

company.

4. Caution in removal and making wiring connection to the

parts for the automobile.

Disconnect the battery terminal after turning the ignition

key off. If wrong wiring connections are made with the

battery connected, a short circuit and/or fire may occur.

If extensive damage is caused due to negligence of re-

pair, the legal responsibility shall be with the repairing

company.

5. Cautions regarding chips.

Do not reuse removed chips even when no abnormality

is observed in their appearance. Always replace them

with new ones. (The chip parts include resistors, capaci-

tors, diodes, transistors, etc). The negative pole of tan-

talum capacitors is highly susceptible to heat, so use

special care when replacing them and check the opera-

tion afterwards.

6. Cautions in handling flexible PWB

Before working with a soldering iron, make sure that the

iron tip temperature is around 270℃. Take care not to

apply the iron tip repeatedly(more than three times)to

the same patterns. Also take care not to apply the tip

with force.

7. Turn the unit OFF during disassembly and parts replace-

ment. Recheck all work before you apply power to the

unit.

■ERROR DISPLAYS

If an error occurs,one of the following displays is displayed.

Take the measure described below to eliminate the problem.

Tape

CHANGER

Error display

ERROR 1

ERROR 2

ERROR 4

ERROR 8

ERROR 2

ERROR 3

ERROR 6

ERROR H

EEROR 2

ERROR 3

ERROR 6

Cause

Tape cannot be played due to defective tape

such as cut tape.

Tape is caught and cannot be played.

Tape mode cannot be detected.

Tape is caught and cannot be ejected.

A CD inside the CD changer is not loaded.

A CD inside the CD changer cannot be played

due to scratches,etc.

A CD inside the CD changer cannot be played

because it is loaded upside-down.

Displayed when the temperature in the MD

changer is too high and playback has been

stopped automatically.

An MD inside the MD changer is not loaded.

An MD inside the MD changer cannot be

played due to scratches,etc.

An MD inside the MD changer cannot be

played because it is loaded upside-down.

Displayed when a non-recorded MD is loaded

in the MD changer.

Measure

Eject the tape then replace it with a new one.

Remove the caught or wound tape.

This is a failure of tape mechanism.

Eliminate the reason for which the tape is caught.

This is a failure of CD changer's mechanism.

Replace with a non-scratched,non-warped-disc.

Eject the disc then reload it properly.

Lower the surrounding temperature and wait for a

while to cool off MD changer.

This is a failure of MD changer's mechanism.

Replace with a non-scratched,non-warped-disc.

Eject the disc then reload it properly.

Load a pre-recorded MD in the MD changer.

If an error other than the ones described above appears,press the reset button.

-3- ARX8570z

Item Procedure Measuring

instrument

■CHANGING THE RECEPTION AREA

This unit is initially set to USA frequency intervals of 10kHz

for AM and 200kHz for FM.When using it outside the

USA,the frequency reception range can be switched to the

intervals below.

Setting the reception area

1. Press BND button and select the desired radio band(FM

or AM).

2. While pressing RDM button,each time you press and

hold the number "1" of the Preset buttons for 2 seconds

or longer,the reception area switches from inside the

USA to outside the USA or from outside the USA to

inside the USA.

*Any station preset memories are lost when the recep-

tion area is changed.

■TROUBLESHOOTING

Problem

Nothing happens when

buttons are pressed.

Display is not accurate.

Cause

The microprocessor has malfunctioned

due to noise,etc.

Solution

Turn off the power,then press the OPEN button and

remove the DCP.

Press the reset button for about 2 seconds with a

thin rod. R e s e t b u tto n

■ADJUSTMENT

Dolby level 1. Playback a Dolby level test tape(400Hz,200nWb/m) and connect the Milli-volt

meter to TP101(L)/TP102(R).

2. Adjust VR101(L)/VR102(R) to obtain an output of TP101(L)/TP102(R) is 388mV

±1dB.(Dolby SW:off)

Dolby test tape

Milli-volt meter

Azimuth

adjustment 1. Playback a azimuth test tape(10kHz,−10VU) and turn each azimuth-adjusting

screw to make each FOW & REV Maximum.

2. After adjustment,make adhesion with bond.

Azimuth test tape

Milli-volt meter

Tape speed 1. Playback a Wow & flutter test tape(3kHz,−10VU) and connect the frequency

counter to TP101(L) or TP102(R).

2. Adjust Speed VR of the motor to obtain an output of TP101(L),TP102(R) is

3000Hz±45Hz.

Wow & flutter test

tape

Frequency counter

■EXPLANATION OF IC

■M30622M8-189GP 052-3344-00 Tuner/Cassette Controller

(Ce-NET)

1. Outward Form : 100 pins QFP

2. Function : GFC-3C cassette mechanism control, PLL IC control, Elec-

tric volume IC control, Ce-NET

3. Terminal Description

pin 1 : N.C. : IN : Not in use.

pin 2 : N.C. : O : Not in use.

pin 3 : APC SENSE : O : "L"= Play, "H"= FF/REW

pin 4 : N.C. : IN : Not in use.

pin 5 : TIME BASE : IN : Time base signal input terminal.

pin 6 : BYTE : IN : Connect to ground.

pin 7 : CNVSS : IN : Connect to ground.

pin 8 : N.C. : IN : Not in use.

pin 9 : N.C. : O : Not in use.

pin 10 : RESET_ : IN : Reset signal input. Negative logic.

pin 11 : X OUT : O : Crystal connection.

pin 12 : VSS : - : Ground.

pin 13 : X IN : IN : Crystal connection.

pin 14 : VCC : - : Positive supply voltage.

pin 15 : N.C. : IN : Not in use.

pin 16 : ACC DET : IN : ACC ON signal input.

pin 17 : B/U DET_ : IN : "L"= Backup OFF

pin 18 : KEY INT_ : IN : Interrupt signal input of FUNC/EJECT key

and DCP take off switch.

pin 19 : 27pinCONNECT: IN : Connect to pin 27.

pin 20 : N.C. : IN : Not in use.

pin 21 : N.C. : IN : Not in use.

pin 22 : N.C. : O : Not in use.

pin 23 : DISP RESET : O : Display IC reset signal output.

pin 24 :PULSE DIMM : O : Pulse dimmer / Back light LED ON signal

output.

pin 25 : N.C. : IN : Not in use.

pin 26 : N.C. : O : Not in use.

pin 27 : IE BUS RX : IN : IE Bus communication line.

pin 28 : IE BUS TX : O : IE Bus communication line.

pin 29 : N.C. : O : Not in use.

pin 30 : N.C. : IN : Not in use.

pin 31 : INITIAL OUT : O : Memory clear signal output to EEPROM.

pin 32 : PLL CE : O : PLL chip enable signal output.

pin 33 : PLL DO : O : PLL serial data output.

pin 34 : PLL DI : IN : PLL serial data input.

pin 35 : PLL SCK : O : PLL serial clock output.

pin 36 : FM STEREO : IN : FM stereo detection signal input.

pin 37 : NON FADER 1 : O : Non fader volume control signal output.

Ref. Table 1.

pin 38 : NON FADER 2 : O : Non fader volume control signal output.

Ref. Table 1.

pin 39 : NON FADER 3 : O : Non fader volume control signal output.

Ref. Table 1.

pin 40 : INITIAL 1 : IN : Destination setting terminal. Ref. Table 2.

pin 41 : INITIAL 2 : IN : Destination setting terminal. Ref. Table 2.

pin 42 : VOLUME CLK : O : Serial clock output to Electric volume.

pin 43 : VOLUME DO : O : Serial data output to Electric volume.

pin 44 : TONE BYPS_ : O : Tone bypass ON signal output. Negative

logic.

pin 45 : N.C. : O : Not in use.

pin 46 : DOLBY ON_ : O : Dolby ON signal output. Negative logic.

pin 47 : DOLBY B/C : O : "L"= Dolby C, "H"=Dolby B.

pin 48 : POWER M 1 : O : Power motor control signal output.

Ref. Table 3.

pin 49 : POWER M 2 : O : Power motor control signal output.

Ref. Table 3.

pin 50 : FWD/REV : O : "L"= FWD, "H"= REV.

pin 51 : N.C. : O : Not in use.

-4-

ARX8570z

pin 52 : APC DETECT_ : IN : "H"= Interval.

pin 53 : TAPE IN : IN : "H"= Tape loading start.

pin 54 : BIT 2 : IN : Mechanism mode switch signal input.

Ref. Table 4.

pin 55 : BIT 1 : IN : Mechanism mode switch signal input.

Ref. Table 4.

pin 56 : BIT 3 : IN : Mechanism mode switch signal input.

Ref. Table 4.

pin 57 : N.C. : O : Not in use.

pin 58 : REEL PULSE : IN : Reel pulse input terminal.

pin 59 : MAIN MOTOR : O : Main motor ON signal output.

pin 60 : VCC : - : Positive supply voltage.

pin 61 : MECH ON : O : Power supply control signal output for the

tape mechanism. "H"= ON.

pin 62 : VSS : - : Ground.

pin 63 : N.C. : IN : Not in use.

pin 64 : N.C. : IN : Not in use.

pin 65 : N.C. : IN : Not in use.

pin 66 : N.C. : IN : Not in use.

pin 67 : N.C. : IN : Not in use.

pin 68 : N.C. : IN : Not in use.

pin 69 : NAVI MUTE : O : Mute signal output for the audio signal of

Navigation.

pin 70 : N.C. : IN : Not in use.

pin 71 : 5V REM : O : 5V power supply ON signal output for Mi-

cro computer.

pin 72 : KEY ILL REM : O : Key illumination ON signal output.

pin 73 : AMP MUTE : O : Mute signal output to Power Amplifier.

pin 74 : SYS MUTE_ : O : System mute signal output. Negative logic.

pin 75 : LINE MUTE : O : Mute signal output for Audio signal of Ce-

NET.

pin 76 : BUS IN/OUT : O : Ce-NET audio bus select signal output.

pin 77 : SYS ACC : O : ACC detect signal output to slave micro

computer.

pin 78 : AMP REM DET_: IN : Input "L" when the remote line is shorted.

pin 79 : AMP REM OUT : O : Amplifier ON signal output terminal.

pin 80 : AUTO ANT : O : Motor antenna ON signal output terminal.

pin 81 : PHONE INT : IN : Telephone interrupt signal input.

pin 82 : N.C. : IN : Not in use.

pin 83 : N.C. : IN : Not in use.

pin 84 : N.C. : IN : Not in use.

pin 85 : N.C. : IN : Not in use.

pin 86 : N.C. : IN : Not in use.

pin 87 : N.C. : O : Not in use.

pin 88 : N.C. : O : Not in use.

pin 89 : N.C. : IN : Not in use.

pin 90 : N.C. : IN : Not in use.

pin 91 : N.C. : IN : Not in use.

pin 92 : ILL DET_ : IN : Illumination ON signal input. Negative logic.

pin 93 : N.C. : IN : Not in use.

pin 94 : A VSS : - : Ground terminal for A/D converter.

pin 95 : KEY A/D : IN : Input terminalofA/D converter for Key judg-

ment. Ref. Table 5.

pin 96 : VREF : IN : Reference voltage input for A/D converter.

pin 97 : A VCC : - : Positive supply voltage for A/D converter.

pin 98 : N.C. : IN : Not in use.

pin 99 : N.C. : O : Not in use.

pin100 : N.C. : O : Not in use.

Table 1. Non fader volume control signal output

ATT N-F 1 (pin37) N-F 2 (pin38) N-F 3 (pin39)

0 L L L

1 L L H

2 L H L

3 L H H

4 H L L

5 H L H

6 H H L

7 H H H

Table 2. Destination setting

U.S.A. Third area Japan

Initial 1 (pin40) H L Don't care

Initial 2 (pin41) L L H

Table 3. Power motor control signal output

Mechanism Mode Power M 1 (pin48) Power M 2 (pin49)

Loading head shift forward H L

Eject head go back L H

Brake H H

Stop L L

Table 4. Mechanism mode switch signal input

Mechanism Mode bit 1(pin55) bit 2(pin54) bit 3(pin56)

Eject H H H

Loading H H L

Stop L H L

FWD FF (REV REW) L L H

FWD REW (REV FF) H L L

FWD Play H L H

REV Play L H H

Table 5. A/D converter for Key judgment (pin95)

Judgment A/D steps

Eject key 0/256 to 25/256

Function key 26/256 to 51/256

With DCP (type A/B) 205/256 to 221/256

With DCP (Deck) 222/256 to 238/256

Without DCP 239/256 to 256/256

■M30622MC-176GP 052-7039-00 CD MD CA Display and

Keys (Ce-NET)

1. Outward Form : 100 pins QFP

2. Function : LCD display control, Key scan, Ce-NET communication

3. Terminal Description

pin 1 : N.C. : IN : Not in use.

pin 2 : CONTRAST : O : LCD Contrast control signal output. (Ana-

log signal)

pin 3 : DISP 5V REM : O : Power supply ON signal output for Display.

pin 4 : N.C. : IN : Not in use.

pin 5 : REMOCON : IN : Remote controller signal input terminal.

pin 6 : BYTE_ : IN : Input "L" at single mode operation.

pin 7 : CNVSS_ : IN : Input "L" at single mode operation.

pin 8 : INITIAL 1 : IN : Destination setting terminal. Ref. Table 1.

pin 9 : INITIAL 2 : IN : Destination setting terminal. Ref. Table 1.

pin 10 : RESET_ : IN : System reset input. Negative logic.

pin 11 : X OUT : O : Crystal connection.

pin 12 : VSS : - : Ground.

pin 13 : X IN : IN : Crystal connection.

pin 14 : VCC : - : Positive supply voltage.

pin 15 : N.C. : IN : Not in use.

pin 16 : SYS ACC IN : IN : ACC ON signal input.

pin 17 : N.C. : IN : Not in use.

pin 18 : N.C. : IN : Not in use.

pin 19 : 27pinCONNECT: IN : Connect to 27pin.

pin 20 : LCD RESET_ : O : LCD driver reset signal output.

Negative logic.

pin 21 : INITIAL IN : IN : EEPROM clear signal input.

pin 22 : N.C. : IN : Not in use.

pin 23 : N.C. : IN : Not in use.

pin 24 : N.C. : IN : Not in use.

pin 25 : N.C. : IN : Not in use.

pin 26 : N.C. : IN : Not in use.

pin 27 : IE BUS RX : IN : IE Bus communication line.

pin 28 : IE BUS TX : O : IE Bus communication line.

pin 29 : N.C. : IN : Not in use.

pin 30 : N.C. : IN : Not in use.

pin 31 : N.C. : IN : Not in use.

pin 32 : N.C. : IN : Not in use.

pin 33 : PROM DO : O : EEPROM Data output.

pin 34 : PROM DI : IN : EEPROM Data input.

pin 35 : PROM SCK : O : EEPROM Clock output.

pin 36 : PROM CS : O : EEPROM Chip select output.

pin 37 : N.C. : IN : Not in use.

pin 38 : N.C. : IN : Not in use.

pin 39 : N.C. : IN : Not in use.

pin 40 : N.C. : IN : Not in use.

pin 41 : N.C. : IN : Not in use.

pin 42 : N.C. : IN : Not in use.

pin 43 : N.C. : IN : Not in use.

pin 44 : N.C. : IN : Not in use.

pin 45 : N.C. : IN : Not in use.

pin 46 : N.C. : IN : Not in use.

pin 47 : N.C. : IN : Not in use.

pin 48 : N.C. : IN : Not in use.

pin 49 : N.C. : IN : Not in use.

pin 50 : N.C. : IN : Not in use.

pin 51 : N.C. : IN : Not in use.

-5- ARX8570z

pin 52 : LED RED : O : Rainbow LED control output.

pin 53 : LED GREEN : O : Rainbow LED control output.

pin 54 : LED BLUE : O : Rainbow LED control output.

pin 55 : N.C. : IN : Not in use.

pin 56 : LCD WR_ : O : Write command output to LCD driver.

Negative logic.

pin 57 : LCD RD_ : O : Read command output to LCD driver.

Negative logic.

pin 58 : LCD CS 1_ : O : Chip enable signal output to LCD driver.

Negative logic.

pin 59 : LCD AO : O : Address/Data select signal output to LCD

driver.

pin 60 : VCC : - : Positive supply voltage.

pin 61 : N.C. : IN : Not in use.

pin 62 : VSS : - : Ground.

pin 63 : D7_ : O : Data/Address output to LCD driver.

Negative logic.

pin 64 : D6_ : O : Data/Address output to LCD driver.

Negative logic.

pin 65 : D5_ : - : Data/Address output to LCD driver.

Negative logic.

pin 66 : D4_ : O : Data/Address output to LCD driver.

Negative logic.

pin 67 : D3_ : O : Data/Address output to LCD driver.

Negative logic.

pin 68 : D2_ : O : Data/Address output to LCD driver.

Negative logic.

pin 69 : D1_ : O : Data/Address output to LCD driver.

Negative logic.

pin 70 : D0_ : O : Data/Address output to LCD driver.

Negative logic.

pin 71 : N.C. : IN : Not in use.

pin 72 : N.C. : IN : Not in use.

pin 73 : N.C. : IN : Not in use.

pin 74 : N.C. : IN : Not in use.

pin 75 : N.C. : IN : Not in use.

pin 76 : N.C. : IN : Not in use.

pin 77 : JOG CCW : IN : Jog key signal input.

pin 78 : JOG CW : IN : Jog key signal input.

pin 79 : N.C. : IN : Not in use.

pin 80 : N.C. : IN : Not in use.

pin 81 : KO 5_ : O : Key scan output terminal.

Negative logic.

pin 82 : KO 4_ : O : Key scan output terminal.

Negative logic.

pin 83 : KO 3_ : O : Key scan output terminal.

Negative logic.

pin 84 : KO 2_ : O : Key scan output terminal.

Negative logic.

pin 85 : KO 1_ : O : Key scan output terminal.

Negative logic.

pin 86 : KO 0_ : O : Key scan output terminal.

Negative logic.

pin 87 : KI 3_ : IN : Key scan input terminal.

Negative logic.

pin 88 : KI 2_ : IN : Key scan input terminal.

Negative logic.

pin 89 : KI 1_ : IN : Key scan input terminal.

Negative logic.

pin 90 : KI 0_ : IN : Key scan input terminal.

Negative logic.

pin 91 : N.C. : IN : Not in use.

pin 92 : RAINBOW IN : IN : Audio signal input terminal of bulit-in A/D

converter, for the rainbow LED.

pin 93 : TEMP DET : IN : Temperature signal input of bulit-in A/D

converter.

pin 94 : A VSS : - : Ground terminal for bulit-in A/D converter.

pin 95 : N.C. : IN : Not in use.

pin 96 : VREF : IN : Reference voltage terminal for bulit-in A/D

converter.

pin 97 : AVCC : - : Positive supply voltage terminal for bulit-in

A/D converter.

pin 98 : N.C. : IN : Not in use.

pin 99 : N.C. : IN : Not in use.

pin100 : N.C. : IN : Not in use.

Table 1. Destination setting

U.S.A. Other Japan Europe

INITIAL 1 ( pin 8 ) H L H L

INITIAL 2 ( pin 9 ) L L H H

-6-

ARX8570z

■BLOCK DIAGRAM

TUNER(FM/AM)

880-2079G

FM /AM

(BUS)AUDIO

TAPE

VOL

E-VOL IC 501 M 62419

TO NE FAD BU FFER MUTE

IN /O U T

SW IN

OUT

L IN E IN /O U T

4ch

NON-FADER

2ch

SP-OUT

4ch

AM P

IC 101 TD A 7386

POW ER IC

IS O L A T IO N

CIRCUIT

PHO NE

IN T

Q 201

2SC 3420

AUDIO

+B SW

IC 211

AN 77L06

CURRENT

LIM ITE R

ACC

B/U

PHO NE

IN T

REM

CURRENT

CIRCUIT

ILLU M I(K EY)

FUNC/POW ER

RESET

ILLU M I(S LO T)

ILLU M I

DETECTOR

ILLU M I

REM+B

EJECT

IC 703

AT93C46

E2PRO M

REMOTE

CONTROL

A/D

IC 702

M 30622M C -176

DISPLAY CPU

D/A

A/D

10M H z

ROTARY

VOL

RGB SW

RGB

KEY

MATRIX

COLOR

LED

SW ITCH PW B

LC D

IC 701 SED 1526

LCD DRIVER

CONTRAST

LCD BACK LIGHT

MAIN MOTOR

DRIVER

TA 7291

PRE

C XA2502

DO LBY B/C

B/C

TAPE MECHANISM

STABI

Q 903

2SD 1802

+B R E M

SW MECH ON

COLOR

KEY

ILLU M I

IC 301

IN V .

AM P

NON-INV.

AM P

IC 602 C A0008

IE -B U S

DRIVER

BUFFER

Q 601

S W IT C H IN G

IC 303

74VH C 4066

IC 302

DIFFER.

AM P

BUS AUDIO +

BUS AUDIO _

(L /R )

13PIN

Ce-NET

SYS ACC

BUS _

BUS+

BU S 14V

ILLU M I

LPF FM +B

SW AM +B

IC 2 LC 72191

PLL IC

7.2M H z

10M H z

LIN E

MUTE

1/2 V C C

IC 502

TO NE

CUT

BA3129 BUF M UTE

LEVEL

DC/DC CONV.

(4 V )

IC 603

NJM2103

RESET

IC 604 S-80721

2.1V

DET

IC 601

M 30622M 8-189

M ASTER CPU

DISP-RESET

KEY-INT

B/U DET

ACC DET

RESET

VDD

AM P REM

AM P

REM

POW ER-ANT

POW ER

ANT

ILLU M I

Tabla de contenidos

Otros manuales de Reproductor de casetes de Clarion

Clarion

Clarion ARX7370R Manual de usuario

Clarion

Clarion AB230 Manual de usuario

Clarion

Clarion ARB2570R Manual de usuario

Clarion

Clarion PU-2134A Manual de usuario

Clarion

Clarion PU-1680A Manual de usuario

Clarion

Clarion ARX9470R Manual de usuario

Clarion

Clarion VDH9600 Manual de usuario

Clarion

Clarion RAX331D Manual de usuario

Manuales populares de Reproductor de casetes de otras marcas

Aiwa

Aiwa TP-VS535 Manual de usuario

Philips

Philips AW 7300 Manual de usuario

Philips

Philips Video Cassette Recorder Manual de usuario

Yamaha

Yamaha MT8X Manual de usuario

Manta

Manta MA408 Manual de usuario

Sherwood

Sherwood Newcastle D-480 Manual de usuario

Tascam

Tascam 122MKIII Guía

GPO

GPO W0162B Manual de usuario

Sony

Sony HST-471 Manual de usuario

Sharp

Sharp JC-AV1 Manual de usuario

Pioneer

Pioneer CT-W103 Manual de usuario

Aiwa

Aiwa HS-JX899 Manual de usuario

Sony

Sony TC-K615S Manual de usuario

Sony

Sony CFS-B15 - Am/fm Stereo Cassette Recorder Manual de usuario

Sony

Sony WMFS220 - Portable Sports AM/FM Cassette... Manual de usuario

Aiwa

Aiwa HS-TA21 Manual de usuario

Sanyo

Sanyo MCD-ZX700F Manual de usuario

Aiwa

Aiwa CS-P77 Manual de usuario