clare ClareOne Keyfob Instrucciones de montaje
© 10JAN20 Clare Controls, LLC. 1 / 3 DOC ID –1899 • Rev 01
ClareOne Keyfob Installation Sheet
Part number: CLR-C1-KF
Description
The ClareOne Keyfob is a battery operated wireless handheld
alarm sensor. When a button is pressed, the associated
command is sent to the ClareOne panel.
Notes
•The keyfob requires that each button is programed with
the desired command (Away, Stay, Disarm, and SOS).
•The keyfob has a range of up to 100 ft. Metal, floors, and
appliances may affect the range.
Important safety instructions
Before you program this sensor, be sure to:
•Read, keep, and follow all instructions.
•When there is a low battery, replace with a compatible
lithium ion battery.
Setup
Use the ClareOne panel to add and setup the keyfob.
To add the keyfob to the panel:
1. Add the sensor to the panel. See “Sensor Management.”
ClareOne User Guide (DOC ID 1871).
2. Once added, test the sensor.
Look at the ClareOne panel, and then press Away/Stay.
Notice that the panel begins to arm.
Note: Testing all sensors to the alarm monitoring station
is strongly advised.
Button function
The keyfob has 4 buttons. Once the keypad is added to the
panel, the buttons control the arming and disarm features of
the panel.
Away: When tapping this button, the panel arms in Away
mode.
Stay: When tapping this button, the panel arms in Stay mode.
Disarm: When tapping this button, the panel is disarmed.
SOS: When tapping this button twice within 3 seconds, the
keyfob sends a panic notification to the alarm monitoring
station.
Battery replacement
The ClareONE Keyfob requires a CR2032 battery. Once the
battery is low, the panel displays a low battery icon next to the
sensor in the devices list. The battery must be replaced within
7 days of the first low battery notification. If the battery is not
replaced within 7 days, the sensor may not function properly.
WARNING: If an incompatible replacement battery is used, or
the battery is installed incorrectly explosion or damages may
occur.
AVERTISSEMENT: Si une batterie de remplacement
incompatible est utilisée ou si la batterie est installée de
manière incorrecte, une explosion ou des dommages peuvent
survenir.
To replace the battery:
Note: Verify that the panel is not armed before changing the
battery.
1. Flip the keyfob onto its face (buttons down), and locate the
screw holding the casing together.
2 / 3 DOC ID –1899 • Rev 01
2. Use a screwdriver to loosen and remove the screw, setting
it aside for resealing the sensor.
3. Slide a fingernail/fingertip into the keyfob’s bottom slot
(area with the keychain protruding), and then push the
keyfob’s back casing upward and away from the front of
the keyfob.
Note: The keychain will come lose in this process, be
careful not to lose the keychain.
4. Hold the circuit board to the front casing.
Note: Do not move the circuit board, if the board is moved
it may result in improper button reporting.
5. Use a fingernail/fingertip to push the battery out of the
casing, noting the polarity of the battery.
6. Slide a new CR2032 battery into the battery casing,
making sure that the polarity is correct.
7. Place the keychain back onto the screw post, and then
press the keyfob’s backplate into place.
8. Place the screw into the screw hole, and then fasten the
screw into the keyfob.
9. Test the keyfob.
Specifications
Compatible panel
ClareOne
Transmitter frequency
433MHz TX
Encrypted
Yes
Buttons
4 Buttons
•Away
•Stay
•Disarm
•SOS
LED indication
1 LED (red)
Battery type
CR2032 (220mAh)
Battery life
5 years
Sensor dimensions
(W × H × D)
1.49 × 2.53 × .55 in.
(38 × 64.5 × 14 mm)
Operating environment
Temperature
Relative humidity
32 to 122.6°F (0 to 50°C)
85% max
Water resistant
IPX4
Regulatory information
Manufacturer
Clare Controls, Llc.
7519 Pennsylvania Ave, Suite 104
Sarasota, FL 34243
North American
standards
ETL listed to: UL 1023, ULC 1023
FCC compliance
FCC ID: 2AVDC-XPD-201
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operation.
Note: This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment generates,
uses and can radiate radio frequency energy and,
if not installed and used in accordance with the
instructions, may cause harmful interference to
radio communications. However, there is no
guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference
to radio or television reception, which can be
determined by turning the equipment off and on,
the user is encouraged to try to correct the
interference by one or more of the following
measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the
equipment and receiver.
-- Connect the equipment into an outlet on a
circuit different from that to which the receiver is
connected.
-- Consult the dealer or an experienced radio/TV
technician for help.
Warning: changes or modifications not expressly
approved by the party responsible for compliance
could void the user’s authority to operate the
equipment.
This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled
environment. This equipment should be installed
and operated with minimum distance 20cm
between the radiator and your body.
DOC ID - 1899 • Rev 01 3 / 3
Environmental
class
UL: Indoor dry
IEC: 3K5
EU compliance
EN 54
EN 54-00:0000
European Union
directives
1999/5/EC (R&TTE directive): Hereby, Clare
Controls declares that this device is in
compliance with the essential requirements and
other relevant provisions of Directive 1999/5/EC.
2004/108/EC (EMC directive): Hereby, Clare
Controls, Llc. Declares that this device is in
compliance with the essential requirements and
other relevant provisions of Directive
2004/108/EC.
2002/96/EC (WEEE directive): Products marked
with this symbol cannot be disposed of as
unsorted municipal waste in the European Union.
For proper recycling, return this product to your
local supplier upon the purchase of equivalent
new equipment, or dispose of it at designated
collection points. For more information see:
www.recyclethis.info.
2006/66/EC (battery directive): This product
contains a battery that cannot be disposed of as
unsorted municipal waste in the European Union.
See the product documentation for specific
battery information. The battery is marked with
this symbol, which may include lettering to
indicate cadmium (Cd), lead (Pb), or mercury
(Hg). For proper recycling, return the battery to
your supplier or to a designated collection point.
For more information see: www.recyclethis.info.
Warranty information
Clare Controls offers a three (3)
year limited warranty on original
Clare Controls components, from
the date of shipment from Clare
Controls. To view complete
limited warranty details, including
limitations and exclusions,
www.clarecontrols.com/warranty.
Scan the
code
to view
product
warranty
details.
Contact information
Clare Controls, LLC.
7519 Pennsylvania Ave, Suite 104
Sarasota, FL 34243
General: 941.328.3991
Fax: 941.870.9646
www.clarecontrols.com
Integrator/Dealer Support: 941.404.1072
Homeowners should contact their installation dealer for
assistance.
Scan the code to
view the full PDF
online.
Este manual sirve para los siguientes modelos
1
Otros manuales de Teclado de clare
