Clare Controls CLIQ.mini Manual de usuario

DOC ID - 1284 • Rev 09 1 / 7

CLIQ.mini Quick Start Guide

Content

Introduction...1

Included and recommended tools...1

CLIQ.mini diagram...2

Installation options...3

LED Display...6

Troubleshooting...6

Warranty Information...7

Support...7

Last modified: 11/11/19

Introduction

Thank you for choosing Clare Controls. In today’s competitive market place, we

can appreciate that you have many choices for your home automation needs.

This document is intended as a quick-start guide, not a full product guide. For

more information, view the full CLIQ.mini Controller Installation and Setup Guide

(DOC ID 1263).

Included and recommended tools

Ensure all accessories are included. If not, contact your dealer.

Included with the CLIQ.mini.

•CLIQ.mini smart home control hub

•Ethernet cable

•Paper clip/Reset tool

•Power over ethernet (PoE) injector

•PoE power supply

•Mounting bracket and screws

•UUID/Mac identification labels

Recommended tools:

•#2 Phillips head screwdriver (used for mounting bracket installation)

•Needle node pliers (used to insert micro USB plug into CLIQ.mini)

DOC ID - 1284 • Rev 09 2 / 7

CLIQ.mini diagram

The following image is a diagram of the CLIQ.mini controller. Use this diagram

during installation and for reference.

Figure 1: CLIQ.mini diagram

(1) Recessed push button

(2) 2 USB ports

(3) Wire routing channel

(4) Wall mount slot

(5) Micro USB port

(6) Ethernet port

DOC ID - 1284 • Rev 09 3 / 7

Installation options

Select an installation option.

Installation Option 1: PoE (Power over Ethernet)

To connect to ClareHome you must have the Install Assist app, a CLIQ.mini

controller, and access to your home’s Wi-Fi.

Note: This method requires that the user has 2 Ethernet cables.

Figure 2: PoE wired connection

To setup your CLIQ.mini using PoE:

1. Connect the CLIQ.mini to the included PoE injector using an ethernet cable.

2. Connect the PoE injector to the router using a second Ethernet cable, and

then plug in the injector’s power supply.

Note: If the LED does not change to solid blue, see “LED Display” on page 6

or “Troubleshooting” on page 6.

3. Download Install Assist app for iOS or Android. You can now use apps to add

smart home devices. Refer to the Clare Controls Knowledge Base for

information on supported devices.

Note: A Fusion project must be created.

DOC ID - 1284 • Rev 09 4 / 7

Installation Option 2: Wi-Fi

To connect the CLIQ.mini using Wi-Fi, you will need access to the Install Assist

app, a CLIQ.mini controller, and the home’s Wi-Fi network.

Figure 3: Wi-Fi connection

To setup your mini using the power supply and ethernet:

1. Connect the CLIQ.mini to the included PoE injector using an ethernet cable.

2. Download the Install Assist app.

3. Open the Wi-Fi settings on your phone and connect to the CLIQ.mini’s

broadcasted network (ClareWifi-xxxx).

4. Open the Install Assist app and tap WiFi Config.

a. Enter the home’s Wi-Fi SSID and password, tap Next, and then follow the

on-screen instructions.

b. Wait for the LED on the CLIQ.mini to turn solid blue. The CLIQ.mini is now

connected to Wi-Fi.

c. Note: If the LED does not change to solid blue, see “LED Display” on

page 6 or “Troubleshooting” on page 6.

DOC ID - 1284 • Rev 09 5 / 7

5. Reconnect your mobile device to your home’s Wi-Fi, and then re-open the

Install Assist app.

6. You can now use the app to add smart home devices. Refer to the Clare

Controls Knowledge Base for information on supported devices.

Note: A Fusion project will also need to be created.

Wall mount

Once the CLIQ.mini is configured and connected to the home’s network, wall

mount the CLIQ.mini.

To wall mount the CLIQ.mini:

1. Attach the mounting bracket to the gang box.

2. Plug in the CLIQ.mini, and then slide it on to the mounting bracket.

DOC ID - 1284 • Rev 09 6 / 7

LED Display

The CLIQ.mini has an LED status indicator. Use the LED chart below to

determine the CLIQ.mini’s status.

Table 1: CLIQ.mini LED status

LED

LED behavior

Solid blue

Everything is working correctly.

Solid red

ClareOS is not operational. Shut down and power cycle the CLIQ.mini.

Blinking blue

The CLIQ.mini is not connected to the internet. Check your router status.

Blinking red

The CLIQ.mini is not connected to your home network. Shutdown and power

cycle the CLIQ.mini.

Note: Rapid blinding indicates Wi-Fi configuration is needed (CLIQ.mini is in AP

mode).

Blinking red and blue

Firmware update in progress, may take up to 10 minutes.

Not lit

There is no power connected to the CLIQ.mini. Check that the power supplies

are plugged in and wired correctly.

Troubleshooting

In certain states the CLIQ.mini must be reset or power cycled.

Note: When the CLIQ.mini reboots, it can take up to 25 seconds to successfully

restart in AP mode.

To shutdown the CLIQ.mini:

1. Slide the provided paper clip/reset tool into the recessed push button and

hold down for 5 seconds.

DOC ID - 1284 • Rev 09 7 / 7

To shutdown and power cycle the CLIQ.mini in AP mode:

1. Slide the provided paper clip/reset tool into the recessed push button and

hold down for 20 seconds.

Warranty Information

Clare Controls offers a three (3) year limited warranty on original Clare Controls

components, from the date of shipment form Clare Controls. To view complete

limited warranty details, including limitations and exclusions, see

www.clarecontrols.com/warranty.

Support

Dealer Support –contact Clare Technical Services at:

[email protected]

Homeowner Support –contact ClareCare

[email protected]

Tabla de contenidos

Otros manuales de Controladores de Clare Controls

Clare Controls

Clare Controls CLIQ.mini Instrucciones de montaje

Clare Controls

Clare Controls CH-OS-L Instrucciones de montaje

Clare Controls

Clare Controls CLIQ.host Instrucciones de montaje

Clare Controls

Clare Controls CLIQ.express Instrucciones de montaje

Clare Controls

Clare Controls CLIQ.lite Controller Instrucciones de montaje

Clare Controls

Clare Controls CLIQ.host Instrucciones de montaje

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario