Citizen CMP-10 Manual de instalación

Command Reference

MOBILE LINE THERMAL PRINTER

MODEL CMP-10

Rev. 3.10 Revised on Dec 13, 2006

Rev. No. Date Comment

Rev. 1.00 2002/11/15 Newly issued

Rev. 1.01 2002/12/18 Revised P. 1, P. 2, P. 47, P. 54, P. 56, P. 59

Rev. 1.02 2003/01/17 Added Chapter 3 (Character Codes Table) and Chapter 4

Rev. 2.00 2003/06/30 Added ESC >, ESC l, FF (Firmware Ver. 1.95)

Revised GS )

Added Chapter 5 to Chapter 10

Rev. 3.00 2006/07/13 Added baud rate 38400 at page of ESC S n and 5.1 (2)

Added GS z

Rev. 3.01 2006/08/31 Revised range of CODE128 on Page56

Rev. 3.10 2006/12/13 Added new Chapter 4. Deleted [Remarks] on page 63.

REVISION

— 1 —

1. CMP-10 COMMAND SET

Code Command Function Page

1BEL Sounds the Buzzer 4

2HT Horizontal Tab Command 5

3LF Printing and Paper Feed Command 6

4CRPrint one line Command 7

5ESC RS Sounds the Buzzer 7

6ESC SP Setting the right space amount of the

character 8

7ESC ! Collective Specifying Printing Mode 9

8ESC $ Specifying the Absolute Positions 11

9ESC % Specifying/Canceling Download Character Set 12

10 ESC & Define user characters 13

11 ESC * Specifying the Bit Image Mode 14

12 ESC + Switch OFF the printer 17

13 ESC – Specifying/ Canceling Underline 17

14 ESC . Printer self test 18

15 ESC 2 Specifying 1/6-inch line feed rate 18

16 ESC 3 Setting line feed rate of minimum pitch 19

17 ESC = Data Input Control 20

18 ESC > Saving current setting 21

19 ESC ? Reading magnetic stripe reader 22

20 ESC @ Initializing the Printer 23

21 ESC D Setting Horizontal Tab Position 24

22 ESC E Specifying/canceling highlighting 25

23 ESC G Specifying/canceling Double Printing 26

24 ESC J Printing and feeding paper n/203 inch 27

25 ESC R Selecting Code table 27

26 ESC S Setting serial interface communication speed 28

27 ESC T Printing Diagnostic information 28

28 ESC V Specifying/Canceling 90°-right- turned

Characters 29

29 ESC Y Specifying print density 30

30 ESC Z Returning diagnostic information 31

31 ESC \ Specifying the relative positions 34

32 ESC _ Setting the printer in default state 34

33 ESC ` Returning the battery voltage and Printer

Head temperature 35

34 ESC a Aligning the characters 36

35 ESC c5 Enabling/Disabling Panel Switches 37

36 ESC d Printing and Feeding the paper by n lines 38

37 ESC v Transmitting the printer status 39

38 ESC x Selecting the time interval for automatically

switching Off the printer 40

39 ESC { Specifying/Canceling the Inverted Characters 41

40 GS ) Setting of printer flags 42

41 GS * Defining the Download Bit Image (LOGO) 43

42 GS / Printing the Download, Bit Image 44

43 GS : Starting/Ending Macro Definition 45

— 2 —

Code Command Function Page

44 GS H Selecting of Printing Position of HRI Code 46

45 GS L Setting the left margin 47

46 GS W Setting the print area width 48

47 GS ^ Executing the Macro 50

48 GS a Enabling/Disabling

ASB (Automatic Status Back) 51

49 GS f Selecting the font of HRI characters 54

50 GS h Selecting the height of the Bar Code 55

51 GS k Printing the bar code 56

52 GS w Selecting the horizontal size (Scale factor) of the Bar Code 61

53 GS z Saving AT command sequences to send to Bluetooth module 62

54 ESC l Specify/canceling black mark function 64

55 FF Printing and paper feeding to the black mark position 64

* indicates a unique command or a non-compatible command.

— 3 —

2. COMMAND DETAILS

2.1 Description of Items

XXXX ALL

[Function] Command Function

[Code] A sequence of code constituting a command is represented in hexadecimal number

for < >H, binary number for < >B, and decimal number for < >, respectively; [ ]k

represents a repeat count of k-times.

[Range] Indicates an argument value (setting range) for the command in hexadecimal number

(partly in decimal number).

* When used for application other than defined in each control, an error may occur.

Always use in the defined range.

[Outline] Describes a command outline.

[Caution] Describes a caution as required.

[Default] Describes an initial value in hexadecimal number for the command when accompanied

by an argument.

[See Also] Describes the associated commands for use.

[Sample Program] Describes a coding example in the Q-BASIC sample program.

* This example is only for your reference and differs depending on the language

used, version, and so on. For details, see the manual for the language used.

— 4 —

BEL

[Function] Sounds the Buzzer

[Code] <07>H

[Outline] By executing this command the buzzer will beep.

This command functions in the same manner as ESC RS.

— 5 —

[Function] Horizontal Tab Command

[Code] <09>H

[Outline] Shifts the printing position to the next horizontal tab position.

•Ignored when the next horizontal tab position has not been set.

[Caution] •The horizontal tab position is set by ESC D.

•Initial setting of the horizontal tab position is each 8 characters in 9th, 17th, 25th,

columns from FONT A.

[See Also] ESC D

[Sample Program]

PRINT #1, “0123456789012345678901”;

PRINT #1, CHR$ (&HA);

PRINT #1, CHR$ (&H9) + “AAA”;

PRINT #1, CHR$ (&H9) + “BBB”;

PRINT #1, CHR$ (&HA);

PRINT #1, CHR$ (&H1B) + “D”;

PRINT #1, CHR$ (3) + CHR$ (7) + CHR$ (14) + CHR$ (0);

PRINT #1, CHR$ (&H9) + “AAA”;

PRINT #1, CHR$ (&H9) + “BBB”;

PRINT #1, CHR$ (&H9) + “CCC” + CHR$ (&HA);

[Print Results]

123456789012345678901

AAA BBB

AAA BBB CCC

← Initially set horizontal tab

← When set to the 4th, 8th, and 15th digits

— 6 —

[Function] Printing and Paper Feed Command

[Code] <0A>H

[Outline] Prints data inside the input buffer and feeds lines based on the line feed amount

having been set.

•The head of the line becomes the next print starting position.

[See Also] ESC 2, ESC 3

[Sample Program]

PRINT #1, “AAA” + CHR$ (&HA);

PRINT #1, “BBB” + CHR$ (&HA);

PRINT #1, CHR$ (&HA);

PRINT #1, “CCC” + CHR$ (&HA);

[Print Results]

AAA ← Print and line feed

BBB ← Print and line feed

← Line feed only

CCC ← Print and line feed

— 7 —

[Function] Print one line Command

[Code ] <0D>H

[Outline] This command is ignored or its action is the same as LF depending on the last

execution of GS ) 2 command (FLAG SETTING COMMAND).

If Flag 2 is 0, carriage return (CR) command is ignored.

If Flag 2 is 1, CR comamnd will act as LF command.

[Default] CR command is ignored. If you want that it acts like LF command set flag 2 to 1 by

GS ) command.

[See Also] GS )

ESC RS

[Function] Sounds the Buzzer

[Code] <1B>H<1E>H

[Outline] By executing this command the buzzer will beep.

This command functions in the same manner as BEL.

— 8 —

ESC SP n

[Function] Setting the right space amount of the character

[Code] <1B>H<20>H<n>

[Range] {0 =< n =< 20(Hex)}

[Outline] The rightward space amount is set in dot unit (1/203 inch unit).

[Caution] The rightward space amount in doublewide mode is made double of the set volume.

[Default] n = 0

[Sample Program]

PRINT #1, CHR$ (&H1B) + “ “ + CHR$ (0);

PRINT #1, “AAAAA” + CHR$ (&HA);

PRINT #1, CHR$ (&H1B) + “ “ + CHR$ (1);

PRINT #1, “AAAAA” + CHR$ (&HA);

PRINT #1, CHR$ (&H1B) + “ “ + CHR$ (12);

PRINT #1, “AAAAA” + CHR$ (&HA);

[Print Results]

AAAAA ← 0-dot space

A A A A A ← 1-dot space

A A A A A ← 12-dot space

Otros manuales para CMP-10

Tabla de contenidos

Otros manuales de Impresora de Citizen

Citizen

Citizen iDP-562 Series Manual de usuario

Citizen

Citizen iDP-3410 Manual de usuario

Citizen

Citizen LINE THERMAL PRINTER CT-S280 Manual de usuario

Citizen

Citizen CZ-01 Manual de usuario

Citizen

Citizen Swift 90 Manual de usuario

Citizen

Citizen CBM-910 Type II Manual de usuario

Citizen

Citizen CL-S521 Manual de instalación y operación

Citizen

Citizen iDP-3540/3541 Manual de usuario

Citizen

Citizen Mini Printer Manual de usuario

Citizen

Citizen CBM-290 Manual de usuario

Citizen

Citizen CT-S601IIS Manual de usuario

Citizen

Citizen CT-S2000 Manual de usuario

Citizen

Citizen iDP-3210 Manual de usuario

Citizen

Citizen CT-S251 Manual de usuario

Citizen

Citizen iDP-3421 Manual de usuario

Citizen

Citizen CMP-10 Manual de usuario

Citizen

Citizen CLP 1001 Manual de usuario

Citizen

Citizen iDP-3535 Manual de usuario

Citizen

Citizen CT-S601 Manual de usuario

Citizen

Citizen CT-S2000 Manual de usuario

Citizen

Citizen iDP-562 Series Manual de usuario

Citizen

Citizen CMP-40 SERIES Manual de usuario

Citizen

Citizen CT-S851 II Manual de usuario

Citizen

Citizen iDP-3410 Manual de usuario

Manuales populares de Impresora de otras marcas

Lexmark

Lexmark 1400 Series Manual

Canon

Canon i70 Series Manual de usuario

Evolis

Evolis Elypso Manual de usuario

Kyocera

Kyocera FS-9530DN Manual de usuario

Canon

Canon LASER SHOT LBP-1210 Manual de usuario

Samsung

Samsung BIXOLON SRP-350plusF Manual de usuario

Canon

Canon PIXMA PRO-1 Series Manual de usuario

Canon

Canon PIXMA G3560 Guía de configuración

Dell

Dell Color Laser Printer 2130cn Manual de usuario

Tektronix

Tektronix Phaser 840 Manual de usuario

Epson

Epson ET-7750 Instrucciones de funcionamiento

Canon

Canon CLBR 460ps Manual de usuario

Eltron

Eltron P210 Guide Manual de usuario

Ricoh

Ricoh MD-P1 Manual de usuario

Epson

Epson SC-F7100 series Manual de usuario

Epson

Epson Stylus C40UX Manual de usuario

Canon

Canon imagePASS-A2 Manual de usuario

Canon

Canon S820D Manual de usuario