Cisco RV134W Manual de usuario

Quick Start Guide

Cisco RV134W VDSL2 Wireless-AC VPN Router

Package Contents

• Cisco RV134W VDSL2 Wireless-AC VPN Router

• Power Adapter

• Ethernet Cable

• This Quick Start Guide

• Pointer Card

• Technical Support Contact Card

• Console Cable

• RJ-11 Cable

2 Cisco RV134W VDSL2 Wireless-AC Quick Start Guide

Welcome

Thank you for choosing the Cisco RV134W VDSL2 Wireless-AC VPN

Router.

The Cisco RV134W provides business class DSL connectivity for SOHO,

small businesses and remote professionals.

This guide describes how to physically install your Cisco RV134W router

and launch the web-based Device Manager.

Installing Cisco RV134W

To prevent the device from overheating or being damaged:

• Ambient Temperature—Do not operate it in an area that exceeds an

ambient temperature of 104°F (40°C).

• Air Flow—Be sure that there is adequate air flow around the device. If

wall mounting the wireless access point, make sure the heat dissipation

holes are to the side.

• Mechanical Loading—Be sure that the device is level and stable to

avoid any hazardous conditions and that it is secure to prevent it from

sliding or shifting out of position. Do not place anything on top of the

wireless access point, as excessive weight might damage it.

Place the Cisco RV134W unit vertically into the stand with the four rubber

feet.

Cisco RV134W VDSL2 Wireless-AC VPN Quick Start Guide 3

Cisco RV134W Features

Front Panel

Power Off when the device is powered off.

Solid green when the device is powered on and booted.

Flashing green when the device is booting or loading the

firmware.

Solid red when the device fails to reboot or system error, or

is in firmware recovery mode.

Internet Off when the VDSL2+/WAN LED is OFF.

Solid green when the device has a DSL WAN IP or Ethernet

WAN IP connection.

Flashing green when the device is sending or receiving

data through DSL WAN.

Solid red when the device got no DSL WAN IP or Ethernet

WAN IP.

VDSL/Ether-

net WAN

Off when the device is powered off or the device is

configured to use the VDSL/Ethernet WAN yet no VDSL/

Ethernet link.

Solid green when the DSL link has been activated.

Flashing green when the device is negotiating with the

DSLAM.

Solid blue when the Ethernet link is on.

Flashing blue when the device is transmitting/receiving

data through Ethernet WAN.

LAN (1-4) The numbered lights correspond to the LAN ports on the

back panel.

Solid green when the corresponding port is connected to

a device.

Flashing green when the port is sending or receiving

data.

WLAN 2.4G Off when the 2.4GHz wireless module is disabled.

Flashing green when the wireless radio is transmitting or

receiving data.

Solid green when the 2.4GHz wireless module is enabled.

4 Cisco RV134W VDSL2 Wireless-AC Quick Start Guide

Back Panel

VDSL—Insert a RJ-11 cable to connect the router to the ISP VDSLAM.

WAN/Ethernet WAN—Connecting the device to a wide area network

device, such as a cable or DSL modem.

LAN (1-4)—RJ-45 device connections to link local area network devices,

such as PCs, print servers, or switches, to the device.

USB—Type A USB port that supports 3G/4G/LTE USB dongles.

Wireless—Switch the slide button to enable or disable Wi-Fi.

RESET—The RESET button has two functions:

• To reboot the unit and retain the current configuration, press and hold

RESET for at least 3, but no more than 10 seconds, by using a paper clip

or a pen tip.

WLAN 5G Off when the 5GHz wireless module is disabled.

Flashing green when the wireless radio is transmitting or

receiving data.

Solid green when the 5GHz wireless module is enabled.

VPN Off when there is no VPN tunnel defined, or all defined VPN

tunnels have been disabled.

Solid green when there is at least one VPN tunnel working.

Solid amber when none of the enabled VPN tunnels are

working.

USB Off when no 3G/4G USB dongle is connected or the USB

dongle is not recognized.

Solid green when the 3G/4G USB dongle is recognized

and currently connecting to the ISP network.

Flashing green when the 3G/4G USB dongle is

successfully connected to the Internet Service Provider

(ISP) and the port is receiving and sending data.

Solid amber when the USB dongle is recognized but fails

to connect to the ISP.

Cisco RV134W VDSL2 Wireless-AC VPN Quick Start Guide 5

• To reboot the unit and restore the factory default configuration, press

and hold in the RESET button for more than 10 seconds. Changes you

have made to the Cisco RV134W configuration are lost.

CONSOLE— Insert the RJ-45 roll-over cable to connect the device to a

console, such as PCs.

POWER— The POWER button is used to turn the power on and off.

12VDC—Power port that connects the device to the provided 12VDC

power adapter.

Side Panel

The side panel of the Cisco RV134W has a Kensington lock slot. You can

use it to attach a cable and lock to the Cisco RV134W.

6 Cisco RV134W VDSL2 Wireless-AC Quick Start Guide

Connecting the Cisco RV134W

NOTE You must connect one PC with an Ethernet cable for the purpose of

the initial configuration. After you complete the initial configuration,

administrative tasks can be performed using a wireless connection.

To connect a PC to the Cisco RV134W for initial configuration:

STEP 1Power off all equipment, including the cable or DSL modem, the

PC, and the Cisco RV134W .

STEP 2For Ethernet WAN connections, connect one end of the Ethernet

cable to your Internet access device (typically a modem), and

connect the other end of the cable to the WAN port.

For VDSL connections, connect your DSL cable directly to the

VDSL port on the device. If required by your Service Provider,

make sure that you use a DSL splitter.

For 3G/4G WAN connection, connect the 3G/4G USB dongle into

the USB port. Then, the firewall router will detect the 3G/4G dongle

and subscribe to the ISP network.

Note: This application must use the specific 3G/4G dongle which is

supported by the router. The 3G/4G SIM card must be configured

with the user defined PIN code.

STEP 3Connect another Ethernet cable from one of the LAN (Ethernet)

ports to the Ethernet port on the PC.

STEP 4Power on the cable or DSL modem and wait until the connection is

active.

STEP 5Connect the power adapter to the device’s POWER port.

CAUTION Use only the power adapter that is supplied with the unit.

Using a different power adapter could damage the device.

The POWER button is on by default. The power light on the front

panel is solid green when the power adapter is connected

properly and the device is finished booting.

STEP 6Plug the other end of the adapter into an electrical outlet. Use the

plug (supplied) specific to your country.

STEP 7Continue with the instructions in the Using the Setup Wizard to

configure the device.

Cisco RV134W VDSL2 Wireless-AC VPN Quick Start Guide 7

Using the Setup Wizard

NOTE The Setup Wizard and Device Manager are supported on

Microsoft Internet Explorer 6.0 or later, Mozilla Firefox 3.0 or later, and

Apple Safari 3.0 or later.

To configure the device by using the Setup Wizard:

STEP 1Power on the PC that you connected to the LAN port in Step 2 of the

Connecting the Cisco RV134W section. Your PC becomes a

DHCP client of the firewall and receives an IP address in the

192.168.1.xxx range.

STEP 2Start a web browser on your PC. In the Address bar, enter the

default IP address of the firewall: 192.168.1.1. A message appears

about the site’s security certificate. The Cisco RV134W uses a

self-signed security certificate and this message appears because

the firewall is not known to your PC. You can safely click Continue

to this website (or the option shown on your particular web

browser) to go to the web site.

STEP 3When the login page appears, enter the user name and password.

The default user name is cisco. The default password is cisco.

Passwords are case sensitive.

NOTE For security reasons, change the default user name and password

as soon as possible. See the Changing the Administrator User Name

and Password section.

STEP 4Click Log In.

Changing the Administrator User Name and Password

STEP 1From the Getting Started page, choose Change Default

Administrator Password.

STEP 2Select Edit Admin Settings.

STEP 3In the Administrator Settings section, enter the new administrator

username. We recommend that you do not use “cisco.”

STEP 4Enter the old password.

STEP 5Enter the new password. Passwords should not contain dictionary

words from any language or the default password, and they should

contain a mix of letters (both upper- and lowercase), numbers, and

symbols. Passwords must be at least 8 but no more than 30

characters.

8 Cisco RV134W VDSL2 Wireless-AC Quick Start Guide

STEP 6Enter the new password again to confirm.

STEP 7Click Save.

Cisco RV134W VDSL2 Wireless-AC VPN Quick Start Guide 9

Where to Go From Here

For EU Lot 26 related results, see www.cisco.com/go/eu-lot26-results.

Support

Cisco Support

Community

www.cisco.com/go/smallbizsupport

Cisco Support and

Resources

www.cisco.com/go/smallbizhelp

Phone Support Contacts www.cisco.com/en/US/support/

tsd_cisco_small_business

_support_center_contacts.html

Cisco Firmware

Downloads

www.cisco.com/go/smallbizfirmware

Select a link to download firmware for Cisco

products. No login is required.

Cisco Open Source

Requests

www.cisco.com/go/

smallbiz_opensource_request

Cisco Partner Central

(Partner Login Required)

www.cisco.com/web/partners/sell/smb

Product Documentation

3G/4G Dongle Support

List

http://www.cisco.com/c/en/us/support/

routers/small-business-rv-series-routers/

products-technical-reference-list.html

Cisco RV134W

Administration Guide

www.cisco.com/go/rv134w

10 Cisco RV134W VDSL2 Wireless-AC Quick Start Guide

Tabla de contenidos

Otros manuales de Enrutador inalámbrico de Cisco

Cisco

Cisco SRP521W Manual de instrucciones

Cisco

Cisco T-Mobile HIPORT+ Manual de usuario

Cisco

Cisco Valet Plus Manual de usuario

Cisco

Cisco Linksys RT31P2 Instrucciones de funcionamiento originales

Cisco

Cisco SR520W-FE-K9 Manual de usuario

Cisco

Cisco 4402 - Wireless LAN Controller Guía

Cisco

Cisco Linksys E900 Manual de usuario

Cisco

Cisco WRT320N - Wireless-N Gigabit Router Wireless Manual de usuario

Cisco

Cisco 7600 SIP 200 - SPA Interface Processor 200 Manual

Cisco

Cisco Linksys WRT54G3G Manual de usuario

Cisco

Cisco Valet Manual de usuario

Cisco

Cisco ASR 9010 Manual de instrucciones

Cisco

Cisco LINKSYS WRT54GX4 Manual de usuario

Cisco

Cisco Linksys EA2700 Manual de usuario

Cisco

Cisco Linksys EA2700 Manual de usuario

Cisco

Cisco Universal Broadband Router Cisco uBR10012 Manual de usuario

Cisco

Cisco Universal Broadband Router Cisco uBR10012 Manual de usuario

Cisco

Cisco ASR 9000 Series Manual de usuario

Cisco

Cisco Valet M10 Manual de usuario

Cisco

Cisco WRT320N - Wireless-N Gigabit Router Wireless Manual de usuario

Cisco

Cisco RV180 Manual de instrucciones

Cisco

Cisco WRT54G2 Linksys Manual de usuario

Cisco

Cisco RV132W Manual de instrucciones

Cisco

Cisco RB-WRT54GS2 - Wireless-G Broadband Router Manual de usuario

Manuales populares de Enrutador inalámbrico de otras marcas

Milesight

Milesight UG67 Manual de usuario

Airlogic

Airlogic AirSync Class 1 Manual del propietario

Samsung

Samsung WCH730B Manual de usuario

TELEFONICA

TELEFONICA USB Adapter Manual de usuario

NETGEAR

NETGEAR PowerLINE WiFi 1000 Series Manual de usuario

Askey

Askey RAC2V1K Manual de usuario

Alloy

Alloy WLF2454AP-S Manual de usuario

TP-Link

TP-Link TL-WR542G Manual de usuario

NETGEAR

NETGEAR WNR2000v4 Manual de usuario

Hama

Hama 53120 Manual de usuario

Intellinet

Intellinet 524582 Manual de usuario

Asus

Asus RT-N10P Manual de usuario

D-Link

D-Link DIR-506L Manual de usuario

Sapido

Sapido GR297n Manual de usuario

Asus

Asus DSL-N55U Manual de usuario

AMTC

AMTC WR7502 Manual de usuario

Compaq

Compaq CP-2W - iPAQ Connection Point Manual de usuario

SMC Networks

SMC Networks WBR14-N2 FICHE Manual de usuario