Cisco Nexus 9000 Series Manual de usuario
Smart Call Home Quick Start Configuration Guide for
Cisco Nexus®9000 Series Switches
Cisco Smart Call Home offers diagnostics and real-time alerts on select Cisco devices, which provides higher
network availability and increased operational efficiency. Smart Call Home is a connected service of Cisco
SMARTnet™for the Nexus 9000.
This document provides the minimum steps to configure and register a Nexus 9000 for Smart Call Home using the
following four available options. It is assumed that the device has the necessary DNS configuration (ip domain-name
and ip name-server for DNS look-ups or ip host for static entries) in order to resolve host-names that may appear in
destination addresses.
1. HTTPS transport from the Nexus 9000 to Cisco
2. Email transport from the Nexus 9000 to Cisco
3. HTTP from the Nexus 9000 to a Transport Gateway (TG) - HTTPS transport to Cisco
4. Email from the Nexus 9000 to a Transport Gateway (TG) - HTTPS transport to Cisco
Note: For security reasons, Cisco recommends customers make use of one of the HTTPS transport options, due to the
additional payload encryption that HTTPS offers. The Transport Gateway software is downloadable from Cisco and
is available for customers who require an aggregation point or a proxy for connection to the internet.
Requirements for Smart Call Home:
NX-OS version 6.1(2) is the minimum version required to support Call Home
A CCO ID associated with an appropriate Cisco SMARTnet™Service contract for your company
Cisco SMARTnet™Service for the device to be registered
Resources for Smart Call Home:
Smart Call Home Support Forum
Cisco Nexus 9000 Series Configuring Smart Call Home
Smart Call Home Server Certificate for HTTPS
Call Home Configuration - HTTPS to Cisco
The following is a sample configuration showing the minimum steps required to configure Call Home
on a Nexus 9000 to communicate with the Smart Call Home System using HTTPS and a command to start
the registration process.
1. Set the system contact - In global configuration mode enter the mandatory system contact using the snmp-
server contact command.
NX-9000#config t
NX-9000(config)#snmp-server contact sys-contact
2. Configure the mandatory contact information (phone number, email address, & street address) and enable
Call Home -
NX-9000(config)#callhome
NX-9000(config-callhome)#email-contact email-address
NX-9000(config-callhome)#phone-contact +1-000-000-0000
NX-9000(config-callhome)#streetaddress a-street-address
NX-9000(config-callhome)#enable
3. Set the destination profile CiscoTAC-1’s transport method and address -
NX-9000(config-callhome)#destination-profile CiscoTAC-1 transport-method http
NX-9000(config-callhome)#destination-profile CiscoTAC-1 http
https://tools.cisco.com/its/service/oddce/services/DDCEService
4. Specify VRF for Callhome messages - If the VRF to be used is not the default, and then set
the VRF using the transport http configuration command. It is critical that DNS look-ups
are enabled and working in the specified VRF.-
NX-9000(config-callhome)# transport http use-vrf vrf-name
5. Set the periodic inventory interval to 30 days -
NX-9000(config-callhome)#periodic-inventory notification interval 30
6. Install a security certificate
Copy the Cisco Server Certificate from the Smart Call Home User's Guide. Configure a trust-point and
prepare to enroll the certificate via the terminal using copy and paste when prompted.
NX-9000(config)#crypto ca trustpoint cisco
NX-9000(config-trustpoint)#enroll terminal
NX-9000(config-trustpoint)#crypto ca authenticate cisco
input (cut & paste) CA certificate (chain) in PEM format;
end the input with a line containing only END OF INPUT :
[ paste the certificate here and accept it ]
Do you accept this certificate? [yes/no]: yes
7. Exit configuration mode and save the configuration -
NX-9000(config)#end
NX-9000#copy running-config startup-config
8. Send a Call Home Inventory message to start the registration process -
NX-9000#callhome test inventory
trying to send test callhome inventory message
successfully sent test callhome inventory message
Receive an email from Cisco and follow the link to complete registration for Smart Call Home.
Call Home Configuration - Email to Smart Call Home
The following is a sample configuration showing the minimum steps required to configure Call Home
on a Nexus 9000 to communicate using email with the Smart Call Home System and a command to start
the registration process.
1. Set the system contact - In global configuration mode enter the mandatory system contact
using the snmp-server contact command.
NX-9000#config t
NX-9000(config)#snmp-server contact sys-contact
2. Configure the mandatory contact information (phone number, email address, & street address)
NX-9000(config)#callhome
NX-9000(config-callhome)#email-contact email-address
NX-9000(config-callhome)#phone-contact +1-000-000-0000
NX-9000(config-callhome)#streetaddress a-street-address
3. Configure the mandatory email server information and from email address - The server address
is an IPv4 address, IPv6 address or domain-name of a SMTP server that Call Home will send
email messages to. Optional port number (default = 25) and VRF may also be configured.
NX-9000(config-callhome)#transport email smtp-server ip-address port 25 use-vrf vrf-name
NX-9000(config-callhome)#transport email from email-address
4. Set the destination profile CiscoTAC-1 email-address to [email protected] -
5. Set the periodic inventory interval to 30 days -
NX-9000(config-callhome)#periodic-inventory notification interval 30
6. Send a Call Home Inventory message to start the registration process -
NX-9000#callhome test inventory
trying to send test callhome inventory message
successfully sent test callhome inventorymessage
Receive an email from Cisco and follow the link to complete registration for Smart Call home.
Call Home Configuration - HTTP to Transport Gateway and HTTPS to Cisco
The following is a sample configuration showing the minimum steps required to configure Call Home on a Nexus 9000 to use HTTP to send Call
Home messages to a Transport Gateway (TG) and a command to start the registration process. The TG will use HTTPS to communicate with the
Smart Call Home System. This assumes that the Transport Gateway software has been installed, configured and registered with Smart Call
Home.
1. Set the system contact - In global configuration mode enter the mandatory system contact
using the snmp-server contact command.
NX-9000#config t
NX-9000(config)#snmp-server contact sys-contact
2. Configure the mandatory contact information (phone number, email address, & street address)
-
NX-9000(config)#callhome
NX-9000(config-callhome)#email-contact email-address
NX-9000(config-callhome)#phone-contact +1-000-000-0000
NX-9000(config-callhome)#streetaddress a-street-address
3. Set the destination profile CiscoTAC-1’s transport method and address - The destination
HTTP address is provided by the Transport Gateway (Refer to Configure the HTTP Server
section).
NX-9000(config-callhome)#destination-profile CiscoTAC-1 transport-method http
NX-9000(config-callhome)#destination-profile CiscoTAC-1 http http://url-from-TG
4. Specify VRF for Callhome messages - If the VRF to be used is not the default, then set the
VRF using the transport http configuration command. It is critical that DNS look-ups are
enabled and working in the specified VRF.
NX-9000(config-callhome)# transport http use-vrf vrf-name
5. Set the periodic inventory interval to 30 days -
NX-9000(config-callhome)#periodic-inventory notification interval 30
6. Send a Call Home Inventory message to start the registration process -
NX-9000#callhome test inventory
send test callhome inventory message
successfully sent test callhome inventorymessage
Receive an email from Cisco and follow the link to complete registration for Smart Call
home.
Call Home Configuration - Email to Transport Gateway and HTTPS to Cisco
The following is a sample configuration showing the minimum steps required to configure Call Home
on a Nexus 9000 to communicate, via a Transport Gateway, with the Smart Call Home System using
HTTPS and a command to start the registration process. The TG will use HTTPS to communicate with the Smart
Call Home System. This assumes that the Transport Gateway software has been installed, configured and registered with
Smart Call Home.
1. Set the system contact - In global configuration mode enter the mandatory system contact
using the snmp-server contact command.
NX-9000#config t
NX-9000(config)#snmp-server contact sys-contact
2. Configure the mandatory contact information (phone number, email address, & street address)
NX-9000(config)#callhome
NX-9000(config-callhome)#email-contact email-address
NX-9000(config-callhome)#phone-contact +1-000-000-0000
NX-9000(config-callhome)#streetaddress a-street-address
3. Configure the mandatory email server information and from email address - The server address
is an IPv4 address, IPv6 address or domain-name of a SMTP server that Call Home will send
email messages to. Optional port number (default = 25) and VRF may also be configured.
NX-9000(config-callhome)#transport email smtp-server ip-address port 25 use-vrf vrf-name
NX-9000(config-callhome)#transport email from email-address
4. Set the destination profile CiscoTAC-1 email-address to an email address for the account
that the Transport Gateway will be accessing -
NX-9000(config-callhome)#destination-profile CiscoTAC-1 email-addr email-address
5. Set the periodic inventory interval to 30 days -
NX-9000(config-callhome)#periodic-inventory notification interval 30
6. Send a Call Home Inventory message to start the registration process -
NX-9000#callhome test inventory
trying to send test callhome inventory message
successfully sent test callhome inventorymessage
Receive an email from Cisco and follow the link to complete the registration for Smart Call home.
Downloading Cisco Transport Gateway Software
To download Cisco Transport Gateway software, go to the Download Software web page. On that page the Related
Information section on the right lists the different OS versions (Linux, Solaris, Windows) of Transport Gateway
software. Find the correct OS version of Transport Gateway software in the list and then click either Download Now
or Add to cart.
After you have downloaded the correct OS version of Transport Gateway software, then refer to the Transport
Gateway Installation/Configuration/Registration sections of the Smart Call Home Users’ Guide for information on
how to install the downloaded code then configure and register the Transport Gateway.
Otros manuales para Nexus 9000 Series
11
Tabla de contenidos
Otros manuales de Cambiar de Cisco
Cisco
Cisco LightStream 100 Manual de usuario
Cisco
Cisco Meraki MS225 Series Manual de usuario
Cisco
Cisco 4503-E - Catalyst Data Bundle Switch Manual de usuario
Cisco
Cisco Gigabit Switch Router Cisco 12012 Guía
Cisco
Cisco MEM-S1-128MB Manual de instalación y operación
Cisco
Cisco MGX 8950 Instrucciones de funcionamiento y seguridad
Cisco
Cisco Catalyst 3560 Manual de usuario
Cisco
Cisco Catalyst 8500 Series Instrucciones originales
Cisco
Cisco Nexus 7000 Series Manual de usuario
Cisco
Cisco MDS 9120 - Fabric Switch Manual de usuario
Cisco
Cisco ME 3400G-2CS - Ethernet Access Switch Manual de usuario
Cisco
Cisco 9000 Series Manual de instrucciones
Cisco
Cisco WS-CBS3120X-S Manual
Cisco
Cisco 3020 - Cisco Catalyst Blade Switch Manual de instrucciones
Cisco
Cisco RSP7000 Instrucciones de funcionamiento y mantenimiento
Cisco
Cisco WS-C3750G-48PS-S Manual de lista de piezas
Cisco
Cisco Aironet 350 Series Manual de instrucciones
Cisco
Cisco Nexus 4001I Manual de usuario
Cisco
Cisco Catalyst 4500 Series Manual de usuario
Cisco
Cisco MDS 9120 - Fabric Switch Manual de usuario
