Cisco MS220-24/48 Series Manual de usuario
MS220-24/48 Series (EOS) Installation Guide
Models
Model number Description
MS220-24 ayer-2 24-port GigabitEthernet switch with 4 SFP
interfaces
MS220-24P ayer-2 24-port GigabitEthernet 370W PoE switch
with 4 SFP interfaces
MS220-48 ayer-2 48-port GigabitEthernet switch with 4 SFP
interfaces
MS220-48 P ayer-2 48-port GigabitEthernet 370W PoE switch
with 4 SFP interfaces
MS220-48FP ayer-2 48-port GigabitEthernet 740W PoE switch
with 4 SFP interfaces
Package contents
In addition to the MS switch, the following are provided (mounting kit provided with 1U models only):
On Mar 16, 2017, Cisco Meraki announced the end-of-sale date for the MS220-24/48 series switch
will be Jul 29, 2017. The end-of-support date is Jul 29, 2024.
Read more about our Product End-of- ife (EO ) Policy.
1
Rack Mount Kit includes:
▪ US 12-24 mounting screws and cage nuts, 5 of each
▪ INT M5 mounting screws and cage nuts, 5 of each
▪ INT M6 mounting screws and cage nuts, 5 of each
▪ Mounting washers
MS220-24 Series front panel
MS220-48 Series front panel
Ports and Status Indicators
The MS uses EDs to inform the user of the device's status. When the device powers on, all the Internet EDs flash
twice. Additional functions are described below, from left to right.
Item Function LED Status Meaning
2
1 Power Solid orange
Switch is unable to
connect to the Meraki
cloud
Flashing green Firmware upgrade in
process
Solid green
Switch is fully
operational and
connected to the
Meraki cloud
Off Switch does not have
power
2 Restore N/A
Restore button to clear
switch IP and local
configuration settings
3 Switch Ports Off No client connected
Solid orange ink operating at 10/
100 Mbps
Solid green ink operating at 1000
Mbps
In addition, there is a RESTORE button available on the front panel.
Insert a paper clip if a restore is required.
• A brief, momentary press: To delete a downloaded configuration and reboot.
• Press and hold for more than 10 sec: To force the unit into a full factory restore.
3
MS220 Series back panel
Power input Power cords may be ordered separately.
RPS2300 Redundant Power Supply (Optional)
The MS220-24 series supports connecting the Cisco RPS2300 for optional power redundancy. MS220-24 series models
support failover and reversion to main power once it has been restored. The following Cisco part numbers are
supported:
Part number Description
PWR-RPS2300 RPS Chassis
C3K-PWR-750WAC 750W RPS Power supply (see recommendations)
C3K-PWR-1150WAC 1150W RPS Power supply (see recommendations)
CAB-RPS2300-E= RPS 22-pin cable
Equipment is to be used only in a restricted access location and installed/operated only by trained service
personnel.
4
RPS power supply matrix
Switch Model Full power load, [switch only / including PoE]
MS220-24 18 W / not applicable
MS220-24P 77 W / 447W
MS220-48 51 W / not applicable
MS220-48 P 135 W / 505 W
MS220-48FP 163 W / 903 W
Example configurations
Example 1: "I have 3 x MS220-24 and 3 x MS220-48 switches connected to my RPS2300"
3 x 18W = 54W
3 x 51W = 153W
54W + 153W = 207W total power draw
Recommended hardware:
1 x PWR-RPS2300
1 x C3K-PWR-750WAC (750W) OR 2 x C3K-PWR-750WAC (750W) for redundancy
6 x CAB-RPS2300-E=
Example 2: I have 6 x MS220-24P switches connected to my RPS2300. I also intend to use the full PoE budget of
370W on each switch and want to back it up in case of a failure.
6W x 447W = 2683W total power draw
Recommended hardware:
5
1 x PWR-RPS2300
2 x C3K-PWR-1150WAC (2300W)
6 x CAB-RPS2300-E=
Example 3: I have 3 x MS220-48 and 3 x MS220-48LP connected to RPS2300. I also intend to use the full PoE budget
on each of the PoE switches but I do not need to back it up in case of a failure.
3 x 51 = 153W
3 x 135 = 405W
153W + 405W = 558W total power draw
Recommended hardware:
1 x PWR-RPS2300
1 x C3K-PWR-750WAC (750W) OR 2 x C3K-PWR-750WAC (750W) for redundancy
6 x CAB-RPS2300-E=
Mounting hardware
The mounting hardware includes a rack mount kit for standard 1U racks. When installing the device, make sure that
there is sufficient space between the rear of the rack and other obstacles to ensure adequate airflow.
Only the RPS2300 chassis (PWR-RPS2300) and accessories are supported. For more information, see
the RPS2300 datasheet
6
Este manual sirve para los siguientes modelos
5
Tabla de contenidos
Otros manuales de Cambiar de Cisco
Cisco
Cisco MDS 9000 Series Manual de usuario
Cisco
Cisco Nexus 7000 Series Manual de usuario
Cisco
Cisco NMH Series Manual de usuario
Cisco
Cisco Catalyst 9200 Series Manual de instrucciones
Cisco
Cisco NCS 4200 Series Manual de usuario
Cisco
Cisco 3560-48TS - Catalyst EMI Switch Manual de usuario
Cisco
Cisco VPN 3000 Manual de usuario
Cisco
Cisco SD2005 Manual de usuario
Cisco
Cisco Laserjet,Color Laserjet 3020 Instrucciones de uso
Cisco
Cisco 5509 - Catalyst Chassis Switch Manual de usuario
Cisco
Cisco Nexus 7000 Series Manual de instalación y funcionamiento
Cisco
Cisco C1000-8T-2G-L Manual de usuario
Cisco
Cisco MDS 9000 Series Manual de usuario
Cisco
Cisco ME 3400E Manual
Cisco
Cisco 2970 - Catalyst Switch Manual
Cisco
Cisco Ethernet Connectors Jackscrew Manual de usuario
Cisco
Cisco IE 2000 Cómo utilizar
Cisco
Cisco 2950G 24 - Catalyst Switch Manual de usuario
Cisco
Cisco Nexus 93120TX Manual
Cisco
Cisco Catalyst 2960-XR Manual de usuario
