Cisco MDS 9700 Series Manual de instrucciones

Installing the Cisco MDS 9700 Series Switches

This chapter describes how to install the Cisco MDS 9700 Series Multilayer Director switches and its

components. This chapter includes the following topics:

•Preparing for Installation, on page 1

•Attaching Bottom-Support Rails to a Two-Post Rack, on page 5

•Attaching Bottom-Support Rails to a Four-Post Rack, on page 6

•System Grounding, on page 25

Preparing for Installation

Before you install, operate, or service the system, read the Regulatory Compliance and Safety Information

for the Cisco MDS 9000 Family for important safety information.

Note

This warning symbol indicates danger. You are in a situation that could cause physical injury. Before you

work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard

practices for preventing accidents. Use the statement number provided at the end of each warning to locate

its translation in the translated safety warnings that accompanied this device. Statement 1071

SAVE THESE INSTRUCTIONS

Warning

This unit is intended for installation in restricted access areas. A restricted access area can be accessed only

through the use of a special tool, lock and key, or other means of security. Statement 1017

Warning

Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement

1030

Warning

Installing the Cisco MDS 9700 Series Switches

A readily accessible two-poled disconnect device must be incorporated in the fixed wiring. Statement 1022

Warning

This section provides the following topics:

Unpacking and Inspecting the Switch

Before you install a new chassis, you need to unpack and inspect it to be sure that you have all the items that

you have ordered and verify that the switch was not damaged during the shipment. If anything is damaged or

missing, contact your customer representative immediately.

We recommend that you use a mechanical lift when the chassis is being moved or lifted. Fully loaded, Cisco

MDS 9706 chassis can weigh up to 325 lb (147.5 kg), Cisco MDS 9710 chassis can weigh up to 449.5 lb

(203.8 kg), and Cisco MDS 9718 chassis can weigh up to 923 lb (419 kg).

Caution

When handling switch components, wear an ESD strap and handle modules by the carrier edges only. An

ESD socket is provided on the chassis. For the ESD socket to be effective, the chassis must be grounded either

through the power cable, the chassis ground, or metal-to-metal contact with a grounded rack.

Caution

Keep the shipping container for use when moving or shipping the chassis in the future. The shipping carton

can be flattened and stored with the pallet.

Tip

If you purchased this product through a Cisco reseller, contact the reseller directly for technical support. If

you purchased this product directly from Cisco Systems, contact Cisco Technical Support at this URL:

http://www.cisco.com/en/US/support/tsd_cisco_worldwide_contacts.html.

Note

The switch is thoroughly inspected before shipment. If any damage occurred during transportation or any

items are missing, contact your customer service representative immediately.

Note

To inspect the shipment, follow these steps:

Step 1 Compare the shipment to the equipment list provided by your customer service representative and ensure that you have

received all items, including the following:

• 1 or 2 supervisor modules

• 1 to 4, 8, or 16 switching modules depending on the Cisco MDS 9700 Series switch

• Up to six crossbar fabric switching modules

Installing the Cisco MDS 9700 Series Switches

Unpacking and Inspecting the Switch

• 3 fan modules

• 1 to 4, 8, or 16 power supplies depending on the Cisco MDS 9700 Series switch

• Grounding lug kit

• Mounting kit

• ESD wrist strap

• Cables and connectors

• Cable management frames

• Left and right side frames

• Top frame

• M4 x 12 mm flat-head Phillips screws (12)

• Front door (1)

• M3X8 mm pan-head screws (2)

• Front door kit optional

Step 2 Check for damage and report any discrepancies or damage to your customer service representative. Keep the following

information ready:

• Invoice number of shipper (see packing slip)

• Model and serial number of the damaged unit

• Description of damage

• Effect of damage on the installation

Required Equipments

You need the following items before beginning the installation:

• Number 1 and number 2 Phillips screwdrivers with torque capability

• 3/16-inch flat-blade screwdriver

• Tape measure and level

• ESD wrist strap or other grounding device

• Antistatic mat or antistatic foam

• Torque wrench and socket for the DC power supply lug nuts

• In addition to the grounding items provided in the accessory kit, you need the following items:

Installing the Cisco MDS 9700 Series Switches

Required Equipments

• Grounding cable (6 AWG recommended), sized according to local and national installation

requirements; the required length depends on the proximity of the Cisco MDS 9700 Series switch

to proper grounding facilities.

• Crimping tool large enough to accommodate girth of the DC lug

• Wire-stripping tool

For the Cisco MDS 9700 Series, you need a mechanical lift to handle the weight of the fully-loaded chassis.

Installation Guidelines

Follow these guidelines when installing a Cisco MDS 9700 Series chassis.

• Plan your site configuration and prepare the site before installing the chassis. We recommend that you

use the site planning tasks listed in Appendix 8, “Site Planning and Maintenance Records.”

• Ensure that there is adequate space around the switch to allow for servicing the switch and for adequate

air flow. Air flow requirements are listed in Appendix 6, “Technical Specifications” .

•Ensure that the air-conditioning meets the heat dissipation requirements listed in Appendix 6, “Technical

Specifications.”

• Ensure that the rack meets the requirements listed in Appendix 2, “Rack Requirements.”

•Ensure that the site power meets the power requirements listed in Appendix 6, “Technical Specifications.”

You can use an uninterruptible power supply (UPS) to protect against power failures.

Avoid UPS types that use ferroresonant technology. These UPS types can become

unstable with systems such as the Cisco MDS 9000 Family, which can have

substantial current draw fluctuations because of fluctuating data traffic patterns.

Caution

• Ensure that circuits are sized according to local and national codes. For North America:

• The 3000-W AC power supplies require a 20-A circuit.

If you are using 200/240 VAC power sources in North America, the circuits must be protected by

two-pole circuit breakers.

To prevent loss of input power, ensure that the total maximum loads on the circuits

supplying power are within the current ratings of the wiring and breakers.

Caution

• Record your installation and configuration information as you work. See Appendix 8, “Site Planning

and Maintenance Records.”

• Use the following screw torques when installing the switch:

• Captive screws: 4 in-lb

• M3 screws: 4 in-lb

• M4 screws: 12 in-lb

Installing the Cisco MDS 9700 Series Switches

Installation Guidelines

• M6 screws: 20 in-lb

• 12-24 screws: 30 in-lb

• 10-20 screws: 22 in-lb

Attaching Bottom-Support Rails to a Two-Post Rack

The bottom-support rails support the weight of the switch chassis in the rack or cabinet. To maximize the

stability of the rack, you must attach these rails at the lowest possible rack unit (RU).

To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to

ensure that the system remains stable. The following guidelines are provided to ensure your safety:

• This unit should be mounted at the bottom of the rack if it is the only unit in the rack.

• When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the

heaviest component at the bottom of the rack.

• If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the

unit in the rack.

Note

Before you begin

Before you can install the bottom support rails for the chassis, you must do the following:

• Verify that a two-post rack is installed and secured to the concrete sub floor (see “Installing a Rack or

Cabinet”).

• If any other devices are stored in the rack or cabinet, verify that they are located below where you plan

to install the switch. Also, verify that lighter devices in the same rack are located above where you plan

to install this switch.

• Verify that the two-post bottom-support rails kit was ordered and shipped with the chassis.

Statement 1006

Step 1 Position one of the two bottom-support rails at the lowest possible RU in the rack or cabinet. Be sure there is at least 9

RU of vertical space above the rails to install the chassis.

Step 2 Use a manual Phillips torque screwdriver to attach the bottom-support rail to the rack using four M6 x 19 mm or 12-24

x 3/4 inch screws and tighten each screw to 40 in. lbs (4.5 N.m) of torque.

Installing the Cisco MDS 9700 Series Switches

Attaching Bottom-Support Rails to a Two-Post Rack

Figure 1: Attaching Bottom-Support Rails to a Rack

Adjustable bottom-support rails1

M6 x 19 mm (or 12-24 x 3/4 in.) Phillips screws 3(6 to 8

per rail)

Step 3 Repeat Steps 1 and 2 to attach the other bottom-support rail to the rack.

Make sure that the two bottom-support rails are level with one another. If they are not level, adjust the higher

rail down to the level of the lower rail.

Note

When the bottom-support rails are installed at the lowest possible RU and are level, you are ready to install the chassis

in the rack or cabinet.

Attaching Bottom-Support Rails to a Four-Post Rack

The bottom-support rails support the weight of the switch chassis in the rack or cabinet. To maximize the

stability of the rack, you must attach these rails at the lowest possible rack unit (RU).

To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to

ensure that the system remains stable. The following guidelines are provided to ensure your safety:

• This unit should be mounted at the bottom of the rack if it is the only unit in the rack.

• When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the

heaviest component at the bottom of the rack.

• If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the

unit in the rack.

Statement 1006

Note

Installing the Cisco MDS 9700 Series Switches

Attaching Bottom-Support Rails to a Four-Post Rack

Before you begin

Before you can install the bottom support rails for the chassis, you must do the following:

• Verify that a four-post rack or cabinet is installed and secured to the concrete subfloor (see “Rack and

Cabinet Requirements”).

• If any other devices are stored in the rack or cabinet, verify that they are located below where you plan

to install the switch. Also, verify that lighter devices in the same rack are located above where you plan

to install this switch.

• Verify that the bottom-support rails kit is included in the switch accessory kit (Unpack and inspect the

chassis shipment for completeness and damage).

Step 1 Position one of the two adjustable bottom-support rails at the lowest possible RU in the rack or cabinet and adjust the

length of the rail so that it stretches from the outer edges of the front and rear vertical mounting rails. Be sure there is at

least 9 RU of vertical space above the rails to install the chassis.

You can expand the rail so that its mounting brackets are spaced between 24 to 32 inches (61.0 to 81.3 cm).

Installing the Cisco MDS 9700 Series Switches

Attaching Bottom-Support Rails to a Four-Post Rack

Figure 2: Positioning Bottom-Support Rail - Cisco MDS 9710 Chassis

Position two bottom-support rails at the lowest RU on the

rack.

Allow at least 24.5 inches (62.2 cm) (14 RU) for each

chassis.

Installing the Cisco MDS 9700 Series Switches

Attaching Bottom-Support Rails to a Four-Post Rack

Figure 3: Positioning Bottom-Support Rail - Cisco MDS 9718 Chassis

Position two bottom-support rails at the lowest RU on the

rack.

Allow at least 45.5 inches (115.6 cm) (26 RU) for each

chassis.

Step 2 Use a manual Phillips torque screwdriver to attach the bottom-support rail to the rack using at least three or four M6 x

19 mm or 12-24 x 3/4 inch screws for each end of the rail (using a total of 6 to 8 screws for the rail as shown Figure 3-4)

and tighten each screw to 40 in. lbs (4.5 N.m) of torque.

Installing the Cisco MDS 9700 Series Switches

Attaching Bottom-Support Rails to a Four-Post Rack

Figure 4: Attaching Bottom-Support Rails to a Rack - Cisco MDS 9710 Chassis

Adjustable bottom-support rails (2)1

M6 x 19 mm (or 12-24 x 3/4 in.) Phillips screws (6 to 8 per

rail).

Figure 5: Attaching Bottom-Support Rails to a Rack - Cisco MDS 9718 Chassis

M6 x 19 mm (or 12-24 x 3/4 in.) Phillips screws (8 per rail)1

Adjustable bottom-support rails (2)2

At least three of the screw holes on each end of the bottom-support rail align to the mounting rail. Use at

least three screws (four if possible) on each end of each bottom support rail.

Note

Installing the Cisco MDS 9700 Series Switches

Attaching Bottom-Support Rails to a Four-Post Rack

Otros manuales para MDS 9700 Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cambiar de Cisco

Cisco

Cisco Ethernet Connectors Jackscrew Manual de usuario

Cisco

Cisco Nexus 9808 Manual

Cisco

Cisco DS-C9216I-K9 Manual de usuario

Cisco

Cisco IE 3000 Manual

Cisco

Cisco Catalyst 5000 Series Guía rápida

Cisco

Cisco Nexus 5000 Series Manual de usuario

Cisco

Cisco C9200CX-8P-2X2G-A Manual

Cisco

Cisco Catalyst Express 520-24LC Manual de usuario

Cisco

Cisco WS-C2950-12 Manual de usuario

Cisco

Cisco Catalyst 3850 Guía de referencia rápida

Cisco

Cisco Cisco Small Business Unmanaged Switch SR224 Manual de usuario

Cisco

Cisco 2950G 24 - Catalyst Switch Manual de usuario

Cisco

Cisco CSS11501 - 100Mbps Ethernet Load Balancing... Manual

Cisco

Cisco 3524-PWR - Catalyst XL Enterprise Edition... Manual

Cisco

Cisco 11500 Series Instrucciones originales

Cisco

Cisco Catalyst 3560-24TS Manual de usuario

Cisco

Cisco Catalyst Series Switch 2940 Manual de usuario

Cisco

Cisco Catalyst 3560E-24PD Instrucciones de funcionamiento e instalación

Cisco

Cisco WS-C3750-48PS-S Manual de usuario

Cisco

Cisco MDS 9000 Series Manual

Cisco

Cisco IE-5000-16S12P Manual de usuario

Cisco

Cisco Meraki MS410 Series Manual de usuario

Cisco

Cisco 2950 - Catalyst Switch Manual de usuario

Cisco

Cisco WS-C2940-8TT-S Manual

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario