Cisco Cisco MDS 9020 - Fabric Switch Manual de usuario

CHAPTER

Send documentation comments to mdsfeedbac[email protected]

3-1

Cisco MDS 9020 Fabric Switch Configuration Guide and Command Reference

OL-6988-02

Initial Configuration

This chapter describes how to initially configure switches so they can be accessed by other devices. This

chapter includes the following sections:

•Starting a Cisco MDS 9020 Fabric Switch, page 3-2

•Initial Setup Routine, page 3-2

•Accessing the Switch, page 3-9

•Assigning a Switch Name, page 3-10

•Where Do You Go Next?, page 3-10

•Verifying the Status of the Switch, page 3-10

•Configuring Date and Time, page 3-11

•Management Interface Configuration, page 3-13

•Default Gateway Configuration, page 3-15

•Telnet Server Connection, page 3-16

•Working with Configuration Files, page 3-16

•Deleting Files, page 3-21

Note No configuration is needed on the Cisco MDS 9020 Fabric Switch for interoperability with Brocade and

McData switches. For information on configuring these third party switches refer to the Cisco MDS

9000 Family Switch-to-Switch Interoperability Configuration Guide.

Send documentation comments to mdsfeedbac[email protected]

3-2

Cisco MDS 9020 Fabric Switch Configuration Guide and Command Reference OL-6988-02

Chapter 3 Initial Configuration

Starting a Cisco MDS 9020 Fabric Switch

The following procedure is a review of the tasks you should have completed during hardware

installation, including starting up the switch. These tasks must be completed before you can configure

the switch.

Before you can configure a switch, follow these steps:

Step 1 Verify the following physical connections for the new Cisco MDS 9020 Fabric Switch:

•The console port is physically connected to a computer terminal (or terminal server).

•The management 10/100 Ethernet port (mgmt0) is connected to an external hub, switch, or router.

Refer to the Cisco MDS 9020 Fabric Switch Hardware Installation Guide for more information.

Tip Save the host ID information for future use (for example, to enable licensed features). The host

ID information is provided in the Proof of Purchase document that accompanies the switch.

Step 2 Verify that the default console port parameters are identical to those of the computer terminal (or

terminal server) attached to the switch console port:

•9600 baud

•8 data bits

•1 stop bit

•No parity

Step 3 Power on the switch. The switch boots automatically and the switch# prompt appears in your terminal

window.

Initial Setup Routine

The first time that you access a Cisco MDS 9020 Fabric Switch, it runs a setup program that prompts

you for the IP address and other configuration information necessary for the switch to communicate over

the Ethernet interface. This information is required to configure and manage the switch.

Note The IP address can be configured from the CLI only. When you power up the switch for the first time,

assign the IP address. After you perform this step, the Cisco Fabric Manager can reach the switch

through the Ethernet port.

Send documentation comments to mdsfeedbac[email protected]

3-3

Cisco MDS 9020 Fabric Switch Configuration Guide and Command Reference

OL-6988-02

Chapter 3 Initial Configuration Initial Setup Routine

Preparing to Configure the Switch

Before you configure a Cisco MDS 9020 Fabric Switch for the first time, you need the following

information:

•Administrator password, including:

–

Creating a password for the administrator (required).

–

Creating an additional login account and password (optional).

•IP address for the switch management interface. The management interface is an out-of-band

Ethernet interface.

•Subnet mask for the switch's management interface (optional).

•IP addresses, including:

–

Destination prefix, destination prefix subnet mask, and next hop IP address, if you want to

enable IP routing. Also, provide the IP address of the default network (optional).

–

Otherwise, provide an IP address of the default gateway (optional).

•SSH service on the switch—To enable this optional service, select the SSH key (rsa) and the number

of key bits (768 to 2048).

•Default domain name (optional).

•NTP server IP address (optional).

•SNMP community string (optional).

•Switch name—This is your switch prompt (optional).

Note Be sure to configure the IP route, the IP default network address, and the IP default gateway address to

enable SNMP access. If IP routing is enabled, the switch uses the IP route and the default network IP

address. If IP routing is disabled, the switch uses the default gateway IP address.

Default Login

The Cisco MDS 9020 Fabric Switch has the network administrator as a default user (admin). You cannot

change the default user at any time. (See the “Role-Based Authorization” section on page 9-5.)

You must explicitly configure a strong password for the Cisco MDS 9020 Fabric Switch. If a password

is trivial (short, easy-to-decipher), your password configuration is rejected. Be sure to configure a strong

password. (See “Configuring User Accounts” section on page 9-6.) If you configure and subsequently

forget this new password, you have the option to recover this password. (See the “Recovering the

Administrator Password” section on page 9-10.)

Send documentation comments to mdsfeedbac[email protected]

3-4

Cisco MDS 9020 Fabric Switch Configuration Guide and Command Reference OL-6988-02

Chapter 3 Initial Configuration

Initial Setup Routine

Setup Options

The setup scenario differs based on the subnet to which you are adding the new switch. You must

configure a Cisco MDS 9020 Fabric Switch with an IP address to enable management connections from

outside of the switch. Figure 3-1 shows a switch that is managed out-of-band over a connection to the

network through an Ethernet port.

Figure 3-1 Management Access to Switches

CLI

GUI DNS server

network

Router

IP address

172.16.1.1

Telnet or

SSH

SNMP

Management LAN

(Ethernet connection)

Switch 2

mgmt 0

(IP address:

172.16.1.2)

Console

connection Out of band

management

subnetwork

79936

Send documentation comments to mdsfeedbac[email protected]

3-5

Cisco MDS 9020 Fabric Switch Configuration Guide and Command Reference

OL-6988-02

Chapter 3 Initial Configuration Initial Setup Routine

Assigning Setup Information

This section describes how to initially configure the switch for both out-of-band and in-band

management.

Note Press Ctrl-C at any prompt to skip the remaining configuration options and proceed with what is

configured until that point. Entering the new password for the administrator is a requirement and cannot

be skipped.

Tip If you do not wish to answer a previously configured question, or if you wish to skip answers to any

questions, press Enter. If a default answer is not available (for example, switch name), the switch uses

previously configured value and skips to the next question.

Configuring Out-of-Band Management

To configure the switch for first time out-of-band access, follow these steps:

Step 1 Power on the switch. The Cisco MDS 9020 Fabric Switch boots automatically.

Step 2 Enter the password for the administrator.

Enter the password for admin: admin123

Step 3 Enter yes to enter the setup mode.

---- Basic System Configuration Dialog ----

This setup utility will guide you through the basic configuration of

the system. Setup configures only enough connectivity for management

of the system.

*Note: setup is mainly used for configuring the system initially,

when no configuration is present. So setup always assumes system

defaults and not the current system configuration values.

Press Enter if you want to skip any dialog. Use ctrl-c at anytime

to skip all remaining dialogs.

Would you like to enter the basic configuration dialog (yes/no): yes

The setup utility guides you through the basic configuration process. Press Ctrl-C at any prompt to end

the configuration process.

Send documentation comments to mdsfeedbac[email protected]

3-6

Cisco MDS 9020 Fabric Switch Configuration Guide and Command Reference OL-6988-02

Chapter 3 Initial Configuration

Initial Setup Routine

Step 4 Enter yes (no is the default) to create additional accounts.

Note Only the admin user name can create or modify user accounts.

Create another login account (yes/no) [n]: yes

While configuring your initial setup, you can create an additional user account (in the network-admin

role) besides the administrator’s account. See the “Role-Based Authorization” section on page 9-5 for

information on default roles and permissions.

a. Enter the user login ID.

Enter the user login ID:

user_name

b. Enter the user password.

Enter the password for user_name:

user-password

Confirm the password for user_name:

user-password

c. Enter the user role.

Enter the user role [network-operator]:network_admin

Step 5 Enter yes (no is the default) to configure the read-only or read-write SNMP community string.

Configure read-only SNMP community string (yes/no) [n]: yes

a. Enter the SNMP community string.

SNMP community string:

snmp_community

Step 6 Enter a name for the switch.

Note The switch name is limited to 32 alphanumeric characters.

Enter the switch name:

switch_name

Step 7 Enter yes (yes is the default) to configure out-of-band management.

Continue with Out-of-band (mgmt0) management configuration? [yes/no]: yes

a. Enter the mgmt0 IP address.

Mgmt0 IP address:

ip_address

b. Enter the mgmt0 subnet mask.

Mgmt0 IP netmask:

subnet_mask

Step 8 Enter yes (yes is the default) to configure the default gateway (recommended).

Configure the default-gateway: (yes/no) [y]: yes

a. Enter the default gateway IP address.

IP address of the default-gateway:

default_gateway

Step 9 Enter yes (yes is the default) to enable Telnet service.

Enable the telnet service? (yes/no) [y]: yes

Send documentation comments to mdsfeedbac[email protected]

3-7

Cisco MDS 9020 Fabric Switch Configuration Guide and Command Reference

OL-6988-02

Chapter 3 Initial Configuration Initial Setup Routine

Step 10 Enter no (no is the default) to disable the SSH service.

Enabled SSH service? (yes/no) [n]: no

Step 11 Enter no (no is the default) to not configure the NTP server.

Configure NTP server? (yes/no) [n]: no

Step 12 Enter noshut (shut is the default) to configure the default switchport interface to the noshut state.

Configure default switchport interface state (shut/noshut) [shut]: noshut

Step 13 Enter deny (deny is the default) to deny a default zone policy configuration.

Configure default zone policy (permit/deny) [deny]: deny

Deny prevents traffic flow to all members of the default zone.

Step 14 You see the new configuration. Review and edit the configuration that you have just entered. Enter no

(no is the default) if you are satisfied with the configuration.

The following configuration will be applied:

username admin password admin_pass role network-admin

switchname switch

interface mgmt0

ip address ip_address subnet_mask

ip default-gateway 10.0.0.254

telnet server enable

no ssh server enable

no system default switchport shutdown

no zone default-zone permit

Would you like to edit the configuration? (yes/no) [n]: no

Step 15 Enter yes (yes is default) to use and save this configuration:

Use this configuration and save it? (yes/no) [y]: yes

Caution If you do not save the configuration at this point, none of your changes are updated the next

time the switch is rebooted. Type yes to save the new configuration and ensure that the system

images are also automatically configured. (See Chapter 4, “Software Images”.)

Send documentation comments to mdsfeedbac[email protected]

3-8

Cisco MDS 9020 Fabric Switch Configuration Guide and Command Reference OL-6988-02

Chapter 3 Initial Configuration

Initial Setup Routine

Using the setup Command

To make changes to the initial configuration at a later time, you can enter the setup command in EXEC

mode.

Note The setup utility is mainly used for the initial configuration when no configuration is present. The setup

utility assumes system defaults and not the current system configuration values.

switch# setup

---- Basic System Configuration Dialog ----

This setup utility will guide you through the basic configuration of

the system. Setup configures only enough connectivity for management

of the system.

*Note: setup always assumes a predefined defaults irrespective

of the current system configuration when invoked from CLI.

Press Enter in case you want to skip any dialog. Use ctrl-c at anytime

to skip away remaining dialogs.

Would you like to enter the basic configuration dialog (yes/no): yes

The setup utility guides you through the basic configuration process.

Send documentation comments to mdsfeedbac[email protected]

3-9

Cisco MDS 9020 Fabric Switch Configuration Guide and Command Reference

OL-6988-02

Chapter 3 Initial Configuration Accessing the Switch

Accessing the Switch

After initial configuration, you can access the switch in the following ways:

•Serial console access—You can use a serial port connection to access the CLI.

•Out-of-band (10/100BASE-T Ethernet) access—You can use Telnet or SSH to access a Cisco MDS

9020 Fabric Switch or use SNMP to connect to Cisco Fabric Manager.

Note To use Cisco Fabric Manager, refer to the Cisco MDS 9000 Family Fabric Manager

Configuration Guide.

Figure 3-2 illustrates serial console access and out-of-band access.

Figure 3-2 Switch Access Options

CLI

GUI DNS server

network

Router

IP address

172.16.1.1

Telnet or

SSH

SNMP

Management LAN

(Ethernet connection)

Switch 2

mgmt 0

(IP address:

172.16.1.2)

Console

connection Out of band

management

subnetwork

79936

Send documentation comments to mdsfeedbac[email protected]

3-10

Cisco MDS 9020 Fabric Switch Configuration Guide and Command Reference OL-6988-02

Chapter 3 Initial Configuration

Assigning a Switch Name

Each switch in the fabric requires a unique name. You can assign names to easily identify the switch by

its physical location, its SAN association, or the organization to which it is deployed. The assigned name

is displayed in the command-line prompt. The switch name is limited to 32 alphanumeric characters.

Note This guide refers to the Cisco MDS 9020 Fabric Switch as switch, and it uses the switch# prompt.

To change the name of the switch, perform this task:

Where Do You Go Next?

After reviewing the default configuration, you can change it or perform other configuration or

management tasks. The initial setup can be performed at the CLI only. However, you can continue to

configure other software features or access the switch after initial configuration by using either the CLI

or the Device Manager and Fabric Manager applications.

To use the Cisco Fabric Manager, refer to the Cisco MDS 9000 Family Fabric Manager Configuration

Guide.

Verifying the Status of the Switch

Before you begin configuring the switch, you need to ensure that the switch is functioning as designed.

To verify the status of a switch at any time, enter the show module command in EXEC mode. A sample

output of the show module command follows:

switch# show module

Mod Ports Module-Type Model Status

--- ----- ------------------------------- ------------------ ------------

1 20 1/2/4 Gbps FC/Supervisor DS-C9020-20K9 active *

Mod Sw Hw World-Wide-Name (WWN)

--- ------------ ------ --------------------------------------------------

1 2.1(2) ------- 10:00:00:0d:ec:19:cb:01

Mod MAC-Address Serial-Num

--- -------------------------------------- ----------

1 00-c0-dd-03-d4-e4 0426a07855

* this terminal session

If the status is OK or active, you can continue with your configuration.

Command Purpose

Step 1 switch# config t Enters configuration mode.

Step 2 switch(config)# switchname myswitch1

myswitch1(config)# Changes the switch name prompt as specified.

Step 3 myswitch1(config)# no switchname

switch(config)# Reverts the switch name prompt to its default (switch#).

Tabla de contenidos

Otros manuales de Cambiar de Cisco

Cisco

Cisco ESW-520-24 Manual de usuario

Cisco

Cisco 2950 - Catalyst Switch Manual de usuario

Cisco

Cisco CBS 350 Series Hoja de especificaciones

Cisco

Cisco 4503-E - Catalyst Data Bundle Switch Manual de usuario

Cisco

Cisco Meraki MS250 Series Manual de usuario

Cisco

Cisco TrustSec Manual de usuario

Cisco

Cisco Nexus 7000 Series Manual de instalación y funcionamiento

Cisco

Cisco SR2024 - Small Business Unmanaged Switch Manual de usuario

Cisco

Cisco 4006 - Catalyst Switch Manual de instrucciones

Cisco

Cisco IE-3000-8TC Manual de instalación

Cisco

Cisco Catalyst 4500 Series Manual de usuario

Cisco

Cisco Catalyst C9200L-24PXG-4X-E Manual

Cisco

Cisco SLM2008PT-NA Manual de instrucciones

Cisco

Cisco Catalyst 2960-XR Manual de servicio

Cisco

Cisco CBS Series Hoja de especificaciones

Cisco

Cisco AJ732A - MDS 9134 Fabric Switch Manual de usuario

Cisco

Cisco Catalyst 3560-C Manual de usuario

Cisco

Cisco SG 200-08P Manual de usuario

Cisco

Cisco Nexus 9332D-H2R NX-OS Manual

Cisco

Cisco MGX 8800 Series Manual

Cisco

Cisco 6260 Manual de usuario

Cisco

Cisco SG350X-24P Manual de usuario

Cisco

Cisco Small Business 300 Manual de usuario

Cisco

Cisco NM-16ESW-PWR= Manual de operación y mantenimiento

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario