Cisco AJ732A - MDS 9134 Fabric Switch Manual de instrucciones

Printed in the U.S.A. November 2009

Product names mentioned herein may be trademarks of their respective companies as reflected by an

associated footnote. The information in this document is subject to change without notice.

Release Notes

hp StorageWorks

C-series Fabric Switches

for SAN-OS 3.3(4a) and

FabricWare 2.1(3)

This document provides additional information about the MDS 9020 Fabric Switch, the MDS

9100 Series Fabric Switches, the MDS 9200 Series Multilayer Fabric Switches, and the MDS

9500 Series Multilayer Directors

2 MDS Multilayer Director & Multilayer Fabric Switches Release Notes

REFER TO THE CISCO RELEASE NOTES FOR A COMPLETE

LIST OF NEW FEATURES AND OTHER INFORMATION

PERTINENT TO THIS RELEASE

As part of the SAN-OS 3.3(4a) image updates provided by HP, the Cisco MDS 9000 Family

Release Notes for SAN-OS 3.3(4a) have been included in the bundle. Also as part of the

FabricWare 2.1(3) image updates provided by HP, the Cisco MDS 9020 Fabric Switch Release

Notes for Cisco MDS 9020 FabricWare Release 2.1(3) have been included. For a complete list

and detailed description of features included in the SAN-OS 3.3(4a) release or the FabricWare

2.1(3) release, refer to the Cisco release notes as appropriate. For information about NX-OS and

mixing NX-OS, SAN-OS, and FabricWare in the same fabric, refer to the hp StorageWorks C-

series Fabric Switches for NX-OS Release Notes.

Note: For the latest supported HP storage products, refer to the HP StorageWorks Single Point of

Connectivity Knowledge (SPOCK) website at http://www.hp.com/storage/spock. You must sign

up for an HP Passport to be granted access.

SOFTWARE, FABRICWARE, AND SAN-OS UPDATES

Customers can now receive updates faster and more efficiently via electronic download by using

HP Software Update Manager (SUM). This is a feature available as part of the support

agreement available online within the HP IT Resource Center (ITRC) at http://www.itrc.hp.com/.

SUM provides online access to view support entitlements, manage release notification profiles,

and download available new software updates as they are available.

Customers with a software support agreement can:

1. Register with the ITRC at http://www.itrc.hp.com to obtain an ITRC User ID. This

step is performed once per user.

2. Link support agreements to an ITRC User ID at

http://www.itrc.hp.com/service/entitlements/linkSupportAgreement.do

The System Handle(s) or SAID (Service Agreement Identifier), as identified in

support agreements is required. This step is performed once per support

agreement.

3. Navigate to “software update manager” at

http://www.itrc.hp.com/service/sum/home.do to manage the software updates for

the support agreements linked to your ITRC user ID.

Although software, FabricWare, and SAN-OS images will continue to be located on

http://www.hp.com for a limited period of time, HP SUM will be the preferred method for

obtaining updates, and will eventually be the only method.

Consult the appropriate Cisco MDS release notes for instructions on how to determine the current

SAN-OS or FabricWare version on your switch.

HP strongly recommends upgrading all fabric switches to the latest supported SAN-OS and

FabricWare versions. All switches in the SAN must be running the same version of SAN-OS in

3 MDS Multilayer Director & Multilayer Fabric Switches Release Notes

order to maintain a consistent version throughout the SAN. For new SAN-OS and FabricWare

features, switch limitations, and caveats, refer to the Cisco MDS 9000 Family Release Notes and

Cisco MDS 9020 Fabric Switch Release Notes.

Fabric Manager is no longer embedded in the SAN-OS software. Fabric Manager is available

from a CD-ROM that ships with the switch, provided by HP in the SAN-OS image bundle, or by

requesting a CD through HP SUM. Fabric Manager Update Installer is provided in the HP SAN-

OS image bungle.

FICON SUPPORT

FICON is supported with SAN-OS on the MDS 9000 series switches. For supported versions and

configurations refer to the SPOCK website at http://www.hp.com/storage/spock. You must sign

up for an HP Passport to be granted access.

4 MDS Multilayer Director & Multilayer Fabric Switches Release Notes

C-SERIES FIBRE CHANNEL SWITCHES, SAN-OS &

FABRICWARE

The C-series MDS 9000 fibre channel switches are available in different models:

MDS

Switch

Model Switch Description Supported Switching Modules Supported

Switch

Software

9513 Director class switch which can

accommodate eleven switching

modules 48-port 4-Gbps FC switching module

24-port 4-Gbps FC switching module

12-port 4-Gbps FC switching module

18/4-port Multiservice module

4-port 10-Gbps FC switching module

32-port 2-Gbps FC switching module

16-port 2-Gbps FC switching module

14/2-port Multiprotocol Services module

8-port IP Storage Services module

4-port IP Storage Services module

Storage Services Module

SAN-OS

9509 Director class switch which can

accommodate seven switching

modules

9506 Director class switch which can

accommodate four switching

modules

9216i

Fabric switch with fourteen 2-Gbps

FC ports, two IP ports, and

accommodates one switching

module

9216A Fabric switch with sixteen 2-Gbps

FC ports, and accommodates one

switching module

9222i

Fabric switch with eighteen 4-

Gbps FC ports, four IP ports, and

accommodates one switching

module

48-port 4-Gbps FC switching module

24-port 4-Gbps FC switching module

12-port 4-Gbps FC switching module

18/4-port Multiservice module

4-port 10-Gbps FC switching module

8-port IP Storage Services module

Storage Services Module

9216 Fabric switch with sixteen 2-Gbps

FC ports, and accommodates one

switching module

32-port 2-Gbps FC switching module

16-port 2-Gbps FC switching module

14/2-port Multiprotocol Services module

8-port IP Storage Services module

4-port IP Storage Services module

Storage Services Module

9120 Fabric switch with twenty 2-Gbps

FC ports N/A

9140 Fabric switch with forty 2-Gbps

FC ports N/A

9134 Fabric switch with twenty four or

thirty two 4-Gbps FC ports and

two 10-Gbps FC ports. N/A

9124 Fabric switch with eight, sixteen,

or twenty-four 4-Gbps FC ports N/A

9124e

Fabric switch for HP c-Class

BladeSystem with eight 4-Gbps

internal FC ports and four external

4-Gbps FC ports or sixteen 4-Gbps

internal FC ports and eight external

4-Gbps FC ports

N/A

9020 Fabric switch with twenty 4-Gbps

FC ports N/A FabricWare

5 MDS Multilayer Director & Multilayer Fabric Switches Release Notes

C-SERIES SWITCH AND SWITCHING MODULE BANDWIDTH

AND PORT GROUP

MDS Product Number of FC

port groups Number of

ports per FC

port group

Bandwidth per

FC port group

(Gbps)

12-port 4-Gbps FC switching module 4 3 12.8

24-port 4-Gbps FC switching module 4 6 12.8

48-port 4-Gbps FC switching module 4 12 12.8

4-port 10-Gbps FC switching module 4 1 10

18/4-port Multiservice module 3 6 12.8

14/2-port Multiprotocol Services module 4 4 line rate

16-port 2-Gbps FC switching module 16 1 2

32-port 2-Gbps FC switching module 8 4 2.5

Storage Services Module (SSM) 8 4 2.5

MDS 9222i 4 6 12.8

MDS 9216i 4 4 line rate

MDS 9216A 3 4 line rate

MDS 9216 3 4 line rate

MDS 9134 4-Gbps ports 8 4 line rate

MDS 9134 10-Gbps ports 2 1 line rate

MDS 9124 6 4 line rate

MDS 9124e 6 4 line rate

MDS 9140 (ports 1-8) 2 4 line rate

MDS 9140 (ports 9-40) 8 4 2.5

MDS 9120 (port 1-4) 1 4 line rate

MDS 9120 (ports 5-20) 4 4 2.5

MDS 9020 1 20 line rate

6 MDS Multilayer Director & Multilayer Fabric Switches Release Notes

SAN-OS 3.3(4a) & FABRICWARE 2.1(3) NAMING CONVENTION

MDS Switch Model Image Type Image Name

9513 kickstart image m9500-sf2ek9-kickstart-mz.3.3.4a.bin

system image m9500-sf2ek9-mz.3.3.4a.bin

9509 with supervisor-2

9506 with supervisor-2

kickstart image m9500-sf2ek9-kickstart-mz.3.3.4a.bin

system image m9500-sf2ek9-mz.3.3.4a.bin

9509 with supervisor-1

9506 with supervisor-1

kickstart image m9500-sf1ek9-kickstart-mz.3.3.4a.bin

system image m9500-sf1ek9-mz.3.3.4a.bin

9222i kickstart image m9200-s2ek9-kickstart-mz.3.3.4a.bin

system image m9200-s2ek9-mz.3.3.4a.bin

9216

9216A

9216i

kickstart image m9200-ek9-kickstart-mz.3.3.4a.bin

system image m9200-ek9-mz.3.3.4a.bin

9140

9120 kickstart image m9100-s1ek9-kickstart-mz.3.3.4a.bin

system image m9100-s1ek9-mz.3.3.4a.bin

9134

9124

9124e

kickstart image m9100-s2ek9-kickstart-mz.3.3.4a.bin

system image m9100-s2ek9-mz.3.3.4a.bin

9020 switch image m9020-s1ek9-mz.2.1.3.bin

Other Images Image Image Name

Storage Services Interface ssi image m9000-ek9-ssi-mz.3.3.4a.bin

Fabric Manager Update Installer FM upgrade image m9000-fm-update-3.3.4a.jar

Management Software &

Documentation bundled CD m9000-cd-3.3.4a.zip

All C-series switches can be managed with the command-line interface (CLI) or Simple Network

Management Protocol (SNMP). The graphical user interfaces (GUI) used to manage all C-series

switches is Cisco Fabric Manager and Cisco Device Manager.

7 MDS Multilayer Director & Multilayer Fabric Switches Release Notes

ADDITIONAL MOUNTING REQUIREMENTS

C-series Fabric Switches can be installed in all HP standard racks. Please note the following

restrictions:

Side-Rail Rack-Mounted Options

All side-rail rack-mounted options must have a minimum of four (4) inch clearance distance

above or below the switch chassis for the C-series MDS 9500 Series Multilayer Directors and

MDS 9200 Series Multilayer Fabric Switches. Side-rail rack-mount options include HP zero-U

options, KVM switches and power distribution units (PDUs). The minimum distance between the

top of the switch to the bottom of any side rail rack mounted option, or the bottom of the switch

and the top of the side rail rack mounted option must be at least four (4) inches.

HP Rack Cabinet Support

For standard HP Rack Cabinets with closed side panels, you must have at least two-and-one-half

inches (2.5 in.) (6.4 cm) of air space between the rack walls and the MDS 9200 and 950xchassis

air vents. For the MDS 9513, you must have at least four inches (4.0 in.) (10.16 cm) of air flow

between the rack walls and the director. If the air space does not meet these minimum

requirements, remove the rack side panels.

The HP 10842 (800mm wide, 42U) Rack Cabinet is ideally used as a networking rack

accommodating primarily switching equipment. It can also be used as a server/switch rack. The

10842 rack is a wider version of the 42U 9000 series rack at 800 mm/31.3 in width. This added

width provides approximately eight additional inches of room outside of the internal mounting

rails, which can be used for cabling.

Other Types of Cabinets

When the C-series MDS 9500 Family Multilayer Directors and MDS 9200 Family Multilayer

Fabric Switches are installed in racks other than those mentioned above, including any open sided

racks, the following guidelines must be followed to prevent overheating:

Closed-sided racks must have at least two-and-one-half inches (2.5 in.) (6.4 cm) of air

space between the walls and the 9200 and 950xchassis air vents. The MDS 9513 must

have at least four inches (4.0 in.) (10.16 cm) of air flow between the rack walls and the

director.

Open-sided racks (for example, racks commonly used for telecommunications

equipment), with switches installed side by side must have at least six inches (6 in.) (15.2

cm) of air space between two different switch chassis

All rack types must have nothing to obstruct the cooling vents with side mounted options

Cabling

When cabling any C-series product, the front door on all HP standard racks should be removed to

allow for adequate cable space; this will ensure a safe bending radius on all fibre channel cables.

This is especially pertinent in high port density (Director) installations. Please consult the

relevant Cisco Hardware Installation Guide for further information.

8 MDS Multilayer Director & Multilayer Fabric Switches Release Notes

SERIAL PORT

You must use the serial interface to configure a switch IP address. Refer to the Cisco MDS 9000

Family Configuration Guide or Cisco MDS 9020 Fabric Switch Configuration Guide for

instructions on how to connect the serial port to a host machine.

INITIAL INSTALLATION RECOMMENDATIONS /

REQUIREMENTS

The C-series MDS 9000 Family of switches does not automatically allow SAN connectivity for

the first-time, out-of-the box power up. For more comprehensive initial setup information,

please refer to the Cisco documentation found at http://www.cisco.com.

Note: The setup dialog prompts for all of the necessary settings.

The following steps must be taken during the first-time setup:

I. To enable all ports on the switch, set the ports to noshut – by default, all switch ports are set

to shut

During the setup command:

Configure default switchport interface state (shut/noshut) [shut]: noshut

II. To allow traffic flow to all members of a default zone, set the default zone to permit

connectivity – by default, zoning is set to deny

During the setup command:

Configure default zone policy (permit/deny) [deny]: permit

III. If upgrading from SAN-OS 1.3(4a) or earlier, enable FCID persistence for all VSANs on

the switch – FCID persistence is enabled by default with SAN-OS 2.0(1b) and newer.

Note: FCID persistence is not supported on the MDS 9020.

Enable persistent FCID for each VSAN using the CLI dialog as follows:

switch# config terminal

switch(config)# fcdomain fcid persistent vsan 1

switch(config)# exit

switch# copy running-config startup-config

In this example, the number 1 at the end of the line is the name of the default VSAN ID. If

additional VSANs were created, you must repeat this command for each additional VSAN.

For example, if you added two more VSANs with ID numbers 2 and 3, you must enter the

following commands:

switch# config terminal

switch(config)# fcdomain fcid persistent vsan 2

switch(config)# fcdomain fcid persistent vsan 3

switch(config)# exit

switch# copy running-config startup-config

9 MDS Multilayer Director & Multilayer Fabric Switches Release Notes

IV. Enable In-Order Delivery of Frame

During a steady-state environment, the hardware and software architecture of the C-series

MDS 9000 Family prevents out-of-order (OOO) frame distribution from occurring. If the

fabric encounters a failure, some devices may not be able to handle any OOO frames. For

this reason, HP requires in-order delivery (IOD) be enabled for all switches. There is a

switch setting to enable in-order of frames during fabric failure.

Note: IOD feature is not supported on the MDS 9020.

Using the Management Console or Telnet to Enable IOD

Use the following procedure to enable in-order delivery (IOD) of frames with management

console or telnet:

1. Log into the switch using either the management console or telnet

2. Enter your network-admin privileged account by entering your login name and

password

switch login: admin

Password: <admin password>

3. Enter the following:

switch# show in-order-guarantee

4. The response shows whether or not in-order delivery is enabled

If the display shows inorder delivery: guaranteed, in-order delivery of frames is

enabled and no other steps are required

If the display shows inorder delivery: not guaranteed, in-order delivery of frames is

disabled; continue to the next step

5. Enter into the configuration mode by entering the following command:

switch# config terminal

6. Enter the following command to set in-order delivery of frames:

switch(config)# in-order-guarantee

switch(config)# exit

7. Enter the following command to verify that in-order delivery is enabled:

switch# show in-order-guarantee

You should see the following response for all VSANs:

inorder delivery: guaranteed

8. Copy the running configuration into the startup configuration by entering the

following:

switch# copy running-config startup-config

Note: The running configuration overwrites the startup configuration.

IOD must be enabled for any additional VSANs created.

10 MDS Multilayer Director & Multilayer Fabric Switches Release Notes

Refer to the Cisco MDS 9000 Family Fabric Manager Switch Configuration Guide to

enable IOD using Device/Fabric Manager.

FABRIC MANAGER & DEVICE MANAGER GUI SETUP

The optional Cisco Fabric/Device Manager GUI (graphical user interface) is a Java application.

The Fabric/Device Manager installation process is based on requirements for installing Java Web

Start. Refer to the Cisco MDS 9000 Fabric Manager Release Notes for system requirements and

installation instructions.

To install Device Manager, use a web browser to make an http:// connection to the IP address of a

C-series switch.

Note: Device Manager cannot be installed from the MDS 9020.

Starting with SAN-OS 3.2(1a), Fabric Manager is no longer embedded in the SAN-OS software.

Fabric Manager is available from a CD-ROM or provided by HP in the SAN-OS image bundle.

For additional information on how to install Fabric Manager refer to the “Installation of Cisco

MDS SAN-OS and Fabric Manager” section in the Cisco MDS 9000 Family Fabric Manager

Configuration Guide.

Starting with SAN-OS 3.3(1a), Fabric Manager Update Installer is provided by HP in the SAN-

OS image bundle. The installer allows the user to upgrade an existing system running Fabric

Manager Standalone or Fabric Manager Server without requiring the Management Software and

Documentation CD.

The following is an example of how to upgrade Windows Fabric Manager using the Fabric

Manager Update Installer.

1. Copy the Installer jar file to your Fabric Manager system

2. At the command prompt, locate the directory where the jar file is placed

3. Type the following command:

java.exe –Xmx512m –jar <jar file>

4. Follow the onscreen instructions provided in the Fabric Manager upgrade software

setup wizard

Refer to the Cisco MDS 9000 Family Fabric Manager Configuration Guide for additional

installation instructions.

Note: The MDS 9020 currently runs FabricWare 2.1(3); HP recommends using the latest supported

Fabric/Device Manager when managing this switch via the GUI.

Otros manuales para AJ732A - MDS 9134 Fabric Switch

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cambiar de Cisco

Cisco

Cisco Catalyst 3120 Guía de inicio rápido

Cisco

Cisco Catalyst 4124 Instrucciones de funcionamiento y seguridad

Cisco

Cisco CATALYST 6000 Guía rápida

Cisco

Cisco Meraki MS320 Series Manual de usuario

Cisco

Cisco 2975 - Catalyst LAN Base Switch Manual de usuario

Cisco

Cisco ME 3400 Series Manual de funcionamiento

Cisco

Cisco IE 4000 Manual de usuario

Cisco

Cisco MDS 9100 Series Manual

Cisco

Cisco SG300 series Manual de usuario

Cisco

Cisco Catalyst 2960 Series Manual de usuario

Cisco

Cisco Catalyst 3560-24TS Manual de usuario

Cisco

Cisco Cisco Small Business Unmanaged Switch SD2008 Manual de usuario

Cisco

Cisco Catalyst 3560E-12SD Manual de instrucciones

Cisco

Cisco 400 Series Manual de usuario

Cisco

Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module... Manual de usuario

Cisco

Cisco MDS 9500 Series Guía de instalación

Cisco

Cisco TOPSPIN SFS 3012 Manual de usuario

Cisco

Cisco 2950 - Catalyst Switch Manual de instalación

Cisco

Cisco ME 6500 Manual de usuario

Cisco

Cisco NME-16ES-1G-P Dimensiones

Cisco

Cisco Catalyst 3032 Manual de usuario

Cisco

Cisco Nexus 7004 Manual de instalación y funcionamiento

Cisco

Cisco Nexus 7706 Manual

Cisco

Cisco Catalyst 3650 Series Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario