Cisco 5509 - Catalyst Chassis Switch Manual de usuario

Quick Installation Guide

CATALYST 5509

Prepare for Installation

Rack-Mount the Switch

Connect the Switch to the Network

Connect the Power

Start the System

INSTRUCTIONS FOR INSERTING AND REMOVING MODULES AND POWER SUPPLIES BEGIN ON PAGE 13.

OK FAN

OK OUTPUT

FAIL

OK FAN

OK OUTPUT

FAIL

PORT 2

Switch Load PCMCIA EJECT

100%

10/100Mbps

LINK

CONSOLE AUX

PORT 1

RESET

FAN

SLOT1

SLOT0

ACTIVE

PS1

PS2

SUPERVISORENGINE II I

10/100 FAST ETHERCHANNEL

MDIX MDIX

WS-U5531-FETX

WS-x5530

10/100Mbps

LINK

SYSTEM

STATUS

PORT 2

Switch Load PCMCIA EJECT

100%

10/100Mbps

LINK

CONSOLE AUX

PORT 1

RESET

FAN

SLOT1

SLOT0

ACTIVE

PS1

PS2

SUPERVISORENGINE II I

10/100 FAST ETHERCHANNEL

MDIX MDIX

WS-U5531-FETX

WS-x5530

10/100Mbps

LINK

SYSTEM

STATUS

FASTETHERNET SWITCHING MODULE

STATUS

FASTETHERNET SWITCHING MODULE

STATUS

FASTETHERNET SWITCHING MODULE

OK FAN

OK OUTPUT

FAIL

OK FAN

OK OUTPUT

FAIL

EJECT AUX

CONSOLE

UTP3

Prepare for Installation

Note: This Quick Installation Guide is intended for experienced installers. For detailed

hardware installation instructions, refer to the Catalyst 5000 Series Installation Guide and the

Catalyst 5000 Series Module Installation Guide.

1Check the packing slip to ensure that all the proper components are present.

2Ensure the site is set up properly:

• Prepare equipment racks

• Ensure the environment is within specification

• Prepare network connections

3Obtain the following equipment:

• ESD grounding strap and antistatic mat

• Numbers 1 and 2 Phillips screwdrivers and 3/16-inch flat blade screwdriver

• Tape measure and level

4Ensure your safety when installing the Catalyst 5509 switch:

• Lift the chassis safely

• Cooperate with the natural laws of electricity

• Ensure that the power service at your site is suitable for the chassis you are

connecting

5Take steps to prevent ESD damage to electronic

components:

• Use an ESD wrist strap when handling

modules or coming into contact with

internal components (see figure)

• Handle modules by the edges only

• Place modules in a static shielding bag

when not installed

Rack-Mount the Switch

Install the shelf brackets and crossbar bracket

1Secure each shelf bracket to the rack using six (three

per side) 12-24 or 10-32 screws.

2Attach the crossbar bracket to the back of the shelf

brackets using two (one per side) M3 screws.

Note: The shelf brackets and crossbar support the

chassis in the rack, so no shelf is required.

Attach the L brackets and cable guide to the chassis

1Attach the L brackets to the chassis using the eight M4 Phillips countersunk-head screws

provided in the rack-mount kit.

2(Optional) Attach the cable guide using the screws provided in the cable management kit.

Cable

guide

OK FAN

OK OUTPUT

FAIL

OK FAN

OK OUTPUT

FAIL

PORT 2

Switch Load PCMCIA EJECT

100%

10/100Mbps

LINK

CONSOLE AUX

PORT 1

RESET

FAN

SLOT1

SLOT0

ACTIVE

PS1

PS2

SUPERVISORENGINE II I

10/100 FAST ETHERCHANNEL

MDIX MDIX

WS-U5531-FETX

WS-x5530

10/100Mbps

LINK

SYSTEM

STATUS

PORT 2

Switch Load PCMCIA EJECT

100%

10/100Mbps

LINK

CONSOLE AUX

PORT 1

RESET

FAN

SLOT1

SLOT0

ACTIVE

PS1

PS2

SUPERVISORENGINE II I

10/100 FAST ETHERCHANNEL

MDIX MDIX

WS-U5531-FETX

WS-x5530

10/100Mbps

LINK

SYSTEM

STATUS

FASTETHERNET SWITCHING MODULE

STATUS

FASTETHERNET SWITCHING MODULE

STATUS

FASTETHERNET SWITCHING MODULE

L bracket

Shelf bracket

Crossbar bracket

Rack-Mount the Switch (continued)

Install the switch in the rack

Note: Three people are required to install the switch in an open rack. To make the switch

easier to lift, remove the power supplies and modules before installing the switch in the rack.

1Position one person on each side of the chassis. Lift the switch and position it on the shelf

brackets and crossbar.

2Align the mounting holes in the L brackets with the mounting holes in the rack.

3Have the third person secure the chassis by inserting the mounting screws through the holes

in the L brackets and into the threaded holes in the mounting posts.

4Use a tape measure and level to ensure the chassis is installed straight and level.

OK FAN

OK OUTPUT

FAIL

OK FAN

OK OUTPUT

FAIL

STATUS

FASTETHERNET SWITCHING MODULE

STATUS

FASTETHERNET SWITCHING MODULE

STATUS

FASTETHERNET SWITCHING MODULE

L bracket

OK FAN

OK OUTPUT

FAIL

OK FAN

OK OUTPUT

FAIL

PORT2

Switch Load PCMCIA EJECT

100%

10/100Mbps

LINK

CONSOLE AUX

PORT1

RESET

FAN

SLOT1

SLOT0

ACTIVE

PS1

PS2

SUPERVISORENGINE III

10/100 FAST ETHERCHANNEL

MDIX MDIX

WS-U5531-FETX

WS-x5530

10/100Mbps

LINK

SYSTEM

STATUS

PORT2

Switch Load PCMCIA EJECT

100%

10/100Mbps

LINK

CONSOLE AUX

PORT1

RESET

FAN

SLOT1

SLOT0

ACTIVE

PS1

PS2

SUPERVISORENGINE III

10/100 FAST ETHERCHANNEL

MDIX MDIX

WS-U5531-FETX

WS-x5530

10/100Mbps

LINK

SYSTEM

STATUS

FASTETHERNET SWITCHING MODULE

STATUS

STATUS 1

STATUS

FASTETHERNET SWITCHING MODULE

FASTETHERNETSWITCHINGMODULE

FASTETHERNET SWITCHING MODULE

STATUS

FASTETHERNET SWITCHING MODULE

CONSOLE AUX

RESET

ACTIVE

CONSOLE

Connect the Switch to the Network

Connect a terminal to the console port

Supervisor Engines I and II

To connect a terminal to the Supervisor Engine I

orII console port, plug an EIA/TIA-232 (RS-232)

DCE DB-25-to-DTE DB-25 straight-through

cable into the console port.

Supervisor Engine III

To connect a terminal to the Supervisor

Engine III console port, plug an

RJ-45-to-RJ-45 straight-through cable into

the console port jack. Use an RJ-45-to-DB-25

or RJ-45-to-DB-9 adapter to connect to the

terminal.

Caution TopreventESDdamagetoelectroniccomponents,alwaysuseanESDwrist

strap when handling modules or coming into contact with internal components.

LINK

100 MBPS

A411

PORT 1

MDIX

1-8

9-16

Connect the Switch to the Network (continued)

Connect the switch ports to the network

Note: If you are not sure which cable and connector to use for a particular module, refer to

the Catalyst 5000 Series Module Installation Guide.

RJ-45

To connect to modules with RJ-45 interfaces, use

Category 5 UTP (100BaseTX, 10/100BaseTX, CDDI,

Token Ring, ATM), Category 3 UTP (10BaseT), or Type 1

STP (Token Ring) cables with male RJ-45 interfaces.

Media-Independent Interface (MII)

Supervisor Engine I and II modules with 100BaseTX

uplinks have MII portsinaddition toRJ-45 ports.To

connect to the MII interfaces, use Category 5 UTP

cables with male MII connectors.

PORTS

1-12

10BaseT

Connect the Switch to the Network (continued)

RJ-21 Telco

Toconnecttomoduleswith RJ-21Telcointerfaces,use

Category 3 UTP cable with male RJ-21 Telco

connectors.

SC-Type Fiber Optic

To connect to modules with SC-type fiber-optic interfaces,

use single-mode or multimode fiber-optic cable with male

SC-type connectors.

ST-Type Fiber Optic

To connect to modules with ST-type fiber-optic

interfaces, use single-mode (FDDI) or multimode

(10BaseFL) fiber-optic cable with male ST-type

connectors.

ACTIVE

LINK

PORT A

UNI-155SM

LINK

DS3 (45 Mbps)

BNC

ACTIVE

LINK

PORT

Connect the Switch to the Network (continued)

MIC-Type Fiber Optic

To connect to the FDDI module MMF

(WS-X5101), use multimode fiber-optic cable

with a male MIC-type connector.

BNC

To connect to the ATM dual PHY DS3 module

(WS-X5166), use 75-ohm RG-59 coaxial cable with

male BNC connectors.

Connect the Power

AC power supplies

1Verify that each power supply is properly installed in its bay. Make sure the power supplies

are OFF (0).

2Connect an AC power cable to each power supply. Use the retaining clip to secure the cord

to each power supply connection.

3Attach each power cable to a grounded outlet. If possible, connect each cable to an outlet

on a separate circuit. Make sure that the source power is within range.

Warning Before you work on anyequipment, be awareof the hazards involved with

electrical circuitry and be familiar with standard practices for preventing accidents.

Caution TopreventESDdamagetoelectroniccomponents,alwaysuseanESDwrist

strap when handling modules or coming into contact with internal components.

OK FAN

OK OUTPUT

FAIL

4Connect the Power (continued)

DC power supplies

1Verify that each power supply is correctly installed in its bay and that the power switches

are OFF (0).

2On each power supply, remove the screws securing the terminal block cover and slide the

cover straight off the terminal block.

3Attach the appropriate lugs to the DC-input wires. (Suggested lugs are AMP 322985 or

52941; suggested DC-input wires are 10-AWG copper conductors.)

4Wire the DC-input power supply to the terminal block (see figure), ensuring that all wire

connections are secure:

a) Connect the ground wire to the ground terminal (you should always connect the

ground wire first and disconnect it last)

b) Connect the –48V wire to the “−” terminal

c) Connect the –48V return to the “+” terminal

Warning Before performing the following procedure, remove power to the

DC-input circuit by turning the circuit breaker OFF.

OK OK

FAN OUTPUT

FAIL

Positive (+)

Negative (-)

Ground

Tabla de contenidos

Otros manuales de Cambiar de Cisco

Cisco

Cisco Cisco Line Card 4500 E-Series Manual de usuario

Cisco

Cisco CBS Series Hoja de especificaciones

Cisco

Cisco Catalyst 3120 Manual

Cisco

Cisco OL-4419-06 Manual de usuario

Cisco

Cisco SFS 3012R Manual

Cisco

Cisco Catalyst 3120 Manual de funcionamiento

Cisco

Cisco PIX 520 - PIX Firewall 520 Manual de usuario

Cisco

Cisco Linksys SGE2000P Manual de usuario

Cisco

Cisco Meraki MS125 Series Manual de usuario

Cisco

Cisco Cisco mds 9216 - fabric switch Manual

Cisco

Cisco 2975 - Catalyst LAN Base Switch Manual de usuario

Cisco

Cisco Catalyst 2360 Manual de usuario

Cisco

Cisco Nexus 9504 Manual

Cisco

Cisco Catalyst 2900 Series XL Manual del operador

Cisco

Cisco Unified 500 Series Manual de usuario

Cisco

Cisco 3020 - Cisco Catalyst Blade Switch Manual de usuario

Cisco

Cisco WS-C3560E-24PD-E Manual de instalación

Cisco

Cisco Catalyst Express 500-24LC Manual de usuario

Cisco

Cisco LightStream 100 Manual de usuario

Cisco

Cisco SD2005 Manual de usuario

Cisco

Cisco Catalyst Express 520 Manual de usuario

Cisco

Cisco Catalyst 2960 Series Manual de funcionamiento

Cisco

Cisco SPS224G4 Manual de usuario

Cisco

Cisco Nexus 9348GC-FX3PH Manual

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario