Cisco UCS C220 M4 Instrucciones de montaje

CHAPTER

3-1

Cisco UCS C220 M4 Server Installation and Service Guide

OL-32473-01

Maintaining the Server

This chapter describes how to diagnose server system problems using LEDs. It also provides information

about how to install or replace hardware components, and it includes the following sections:

•Server Monitoring and Management Tools, page 3-1

•Status LEDs and Buttons, page 3-2

•Preparing for Server Component Installation, page 3-8

•Installing or Replacing Server Components, page 3-11

•Service DIP Switches, page 3-67

Server Monitoring and Management Tools

Cisco Integrated Management Interface

You can monitor the server inventory, health, and system event logs by using the built-in Cisco Integrated

Management Controller (Cisco IMC) GUI or CLI interfaces. See the user documentation for your

firmware release at the following URL:

http://www.cisco.com/en/US/products/ps10739/products_installation_and_configuration_guides_list.html

Server Configuration Utility

Cisco has also developed the Cisco Server Configuration Utility for C-Series servers, which can aid and

simplify the following tasks:

•Monitoring server inventory and health

•Diagnosing common server problems with diagnostic tools and logs

•Setting the BIOS booting order

•Configuring some RAID configurations

•Installing operating systems

You can download the ISO image from Cisco.com. See the user documentation for your version of the

utility at the following URL:

http://www.cisco.com/en/US/products/ps10493/products_user_guide_list.html

3-2

Cisco UCS C220 M4 Server Installation and Service Guide

OL-32473-01

Chapter 3 Maintaining the Server

Status LEDs and Buttons

This section describes the location and meaning of LEDs and buttons and includes the following topics

•Front Panel LEDs, page 3-2

•Rear Panel LEDs and Buttons, page 3-5

•Internal Diagnostic LEDs, page 3-7

Front Panel LEDs

Figure 3-1 shows the front panel LEDs. Table 3-1 defines the LED states.

Figure 3-1 Front Panel LEDs

1Hard drive fault LED

Note: NVMe PCIe SSDs drive tray LEDs

have slightly different behavior. See Table 3-1

for the LED states.

6Fan status LED

2Hard drive activity LED 7Temperature status LED

3Power button/power status LED 8Power supply status LED

4Identification button/LED 9Network link activity LED

5System status LED

353088

975

3 4 6 8

BAY 02

BAY 01 BAY 03

BAY 04 BAY 05 BAY 06 BAY 08

BAY 07

3-3

Cisco UCS C220 M4 Server Installation and Service Guide

OL-32473-01

Chapter 3 Maintaining the Server

Status LEDs and Buttons

Table 3-1 Front Panel LEDs, Definitions of States

LED Name State

SAS

SAS/SATA drive fault

Note: If your controller is a

Cisco UCS RAID SAS 9300-8i

or 9300-8e HBA, see Cisco UCS

SAS 9300-8e HBA

Considerations, page C-4 for

differing LED behavior.

•Off—The hard drive is operating properly.

•Amber—Drive fault detected.

•Amber, blinking—The device is rebuilding.

•Amber, blinking with one-second interval—Drive locate function activated.

SAS

SAS/SATA drive activity •Off—There is no hard drive in the hard drive tray (no access, no fault).

•Green—The hard drive is ready.

•Green, blinking—The hard drive is reading or writing data.

PCIe

NVMe PCIe SSD status

(SFF, 8-drives version only)

•Off—The drive is not in use and can be safely removed.

•Green—The drive is in use and functioning properly.

•Green, blinking—the driver is initializing following insertion or the driver is

unloading following an eject command.

•Amber—The drive has failed.

•Amber, blinking—A drive Locate command has been issued in the software.

PCIe

NVMe PCIe SSD activity

(SFF, 8-drives version only)

•Off—No drive activity.

•Green, blinking—There is drive activity.

3Power button/LED •Off—There is no AC power to the server.

•Amber—The server is in standby power mode. Power is supplied only to the

Cisco IMC and some motherboard functions.

•Green—The server is in main power mode. Power is supplied to all server

components.

4Unit identification •Off—The unit identification function is not in use.

•Blue—The unit identification function is activated.

3-4

Cisco UCS C220 M4 Server Installation and Service Guide

OL-32473-01

Chapter 3 Maintaining the Server

Status LEDs and Buttons

5System status •Green—The server is running in normal operating condition.

•Green, blinking—The server is performing system initialization and memory

check.

•Amber, steady—The server is in a degraded operational state. For example:

–

Power supply redundancy is lost.

–

CPUs are mismatched.

–

At least one CPU is faulty.

–

At least one DIMM is faulty.

–

At least one drive in a RAID configuration failed.

•Amber, blinking—The server is in a critical fault state. For example:

–

Boot failed.

–

Fatal CPU and/or bus error is detected.

–

Server is in an over-temperature condition.

6Fan status •Green—All fan modules are operating properly.

•Amber, steady—One or more fan modules breached the critical threshold.

•Amber, blinking—One or more fan modules breached the non-recoverable

threshold.

7Temperature status •Green—The server is operating at normal temperature.

•Amber, steady—One or more temperature sensors breached the critical

threshold.

•Amber, blinking—One or more temperature sensors breached the

non-recoverable threshold.

8Power supply status •Green—All power supplies are operating normally.

•Amber, steady—One or more power supplies are in a degraded operational state.

•Amber, blinking—One or more power supplies are in a critical fault state.

9Network link activity •Off—The Ethernet link is idle.

•Green—One or more Ethernet LOM ports are link-active, but there is no

activity.

•Green, blinking—One or more Ethernet LOM ports are link-active, with

activity.

Table 3-1 Front Panel LEDs, Definitions of States (continued)

LED Name State

3-5

Cisco UCS C220 M4 Server Installation and Service Guide

OL-32473-01

Chapter 3 Maintaining the Server

Status LEDs and Buttons

Rear Panel LEDs and Buttons

Figure 3-2 shows the rear panel LEDs and buttons. Table 3-2 defines the LED states.

Figure 3-2 Rear Panel LEDs and Buttons

1Optional mLOM card LEDs

(not shown, see Table 3-2)

51-Gb Ethernet link status LED

21-Gb Ethernet dedicated management link

status LED

6Rear unit identification button/LED

31-Gb Ethernet dedicated management link

speed LED

7Power supply status LED

41-Gb Ethernet link speed LED

Table 3-2 Rear Panel LEDs, Definitions of States

LED Name State

1Optional mLOM 10-Gb SFP+

(there is a single status LED)

•Off—No link is present.

•Green, steady—Link is active.

•Green, blinking—Traffic is present on the active link.

1Optional mLOM 10-Gb BASE-T

link speed

•Off—Link speed is 10 Mbps.

•Amber—Link speed is 100 Mbps/1 Gbps.

•Green—Link speed is 10 Gbps.

1Optional mLOM 10-Gb BASE-T

link status

•Off—No link is present.

•Green—Link is active.

•Green, blinking—Traffic is present on the active link.

21-Gb Ethernet dedicated

management link speed

•Off—Link speed is 10 Mbps.

•Amber—Link speed is 100 Mbps.

•Green—Link speed is 1 Gbps.

31-Gb Ethernet dedicated

management link status

•Off—No link is present.

•Green—Link is active.

•Green, blinking—Traffic is present on the active link.

41-Gb Ethernet link speed •Off—Link speed is 10 Mbps.

•Amber—Link speed is 100 Mbps.

•Green—Link speed is 1 Gbps.

353089

mLOM

PCIe 01 PCIe 02

PSU 01 PSU 02

1 32 5 6 74

3-6

Cisco UCS C220 M4 Server Installation and Service Guide

OL-32473-01

Chapter 3 Maintaining the Server

Status LEDs and Buttons

51-Gb Ethernet link status •Off—No link is present.

•Green—Link is active.

•Green, blinking—Traffic is present on the active link.

6Rear unit identification •Off—The unit identification LED is not in use.

•Blue—The unit identification LED is activated.

7Power supply status AC power supplies:

•Off—No AC input (12 V main power off, 12 V standby power off).

•Green, blinking—12 V main power off; 12 V standby power on.

•Green, solid—12 V main power on; 12 V standby power on.

•Amber, blinking—Warning threshold detected but 12 V main power on.

•Amber, solid—Critical error detected; 12 V main power off (for example,

over-current, over-voltage, or over-temperature failure).

DC power supply (UCSC-PSUV2-1050DC):

•Off—No DC input (12 V main power off, 12 V standby power off).

•Green, blinking—12 V main power off; 12 V standby power on.

•Green, solid—12 V main power on; 12 V standby power on.

•Amber, blinking—Warning threshold detected but 12 V main power on.

•Amber, solid—Critical error detected; 12 V main power off (for example,

over-current, over-voltage, or over-temperature failure).

Table 3-2 Rear Panel LEDs, Definitions of States (continued)

LED Name State

3-7

Cisco UCS C220 M4 Server Installation and Service Guide

OL-32473-01

Chapter 3 Maintaining the Server

Status LEDs and Buttons

Internal Diagnostic LEDs

The server has internal fault LEDs for CPUs, DIMMs, fan modules, SD cards, the RTC battery, and the

mLOM card. These LEDs are available only when the server is in standby power mode. An LED lights

amber to indicate a faulty component.

See Figure 3-3 for the locations of these internal LEDs.

Figure 3-3 Internal Diagnostic LED Locations

1Fan module fault LEDs (one next to each fan

connector on the motherboard)

4SD card fault LEDs (one next to each bay)

2CPU fault LEDs (one in front of each CPU) 5RTC battery fault LED

3DIMM fault LEDs (one in front of each

DIMM socket on the motherboard)

6mLOM card fault LED (on motherboard next

to mLOM socket)

Table 3-3 Internal Diagnostic LEDs, Definition of States

LED Name State

Internal diagnostic LEDs (all) •Off—Component is functioning normally.

•Amber—Component has failed.

353090

13 4

3-8

Cisco UCS C220 M4 Server Installation and Service Guide

OL-32473-01

Chapter 3 Maintaining the Server

Preparing for Server Component Installation

This section describes how to prepare for component installation, and it includes the following topics:

•Required Equipment, page 3-8

•Shutting Down and Powering Off the Server, page 3-8

•Removing and Replacing the Server Top Cover, page 3-9

•Serial Number Location, page 3-10

•Hot-Swap or Hot-Plug Replacement, page 3-10

Required Equipment

The following equipment is used to perform the procedures in this chapter:

•Number 2 Phillips-head screwdriver

•Electrostatic discharge (ESD) strap or other grounding equipment such as a grounded mat

Shutting Down and Powering Off the Server

The server can run in two power modes:

•Main power mode—Power is supplied to all server components and any operating system on your

drives can run.

•Standby power mode—Power is supplied only to the service processor and the cooling fans and it

is safe to power off the server from this mode.

You can invoke a graceful shutdown or a hard shutdown by using either of the following methods:

•Use the Cisco IMC management interface.

•Use the Power button on the server front panel. To use the Power button, follow these steps:

Step 1 Check the color of the Power Status LED (see the “Front Panel LEDs” section on page 3-2).

•Green—The server is in main power mode and must be shut down before it can be safely powered

off. Go to Step 2.

•Amber—The server is already in standby mode and can be safely powered off. Go to Step 3.

Step 2 Invoke either a graceful shutdown or a hard shutdown:

Caution To avoid data loss or damage to your operating system, you should always invoke a graceful shutdown

of the operating system.

•Graceful shutdown—Press and release the Power button. The operating system performs a graceful

shutdown and the server goes to standby mode, which is indicated by an amber Power Status LED.

•Emergency shutdown—Press and hold the Power button for 4 seconds to force the main power off

and immediately enter standby mode.

Step 3 Disconnect the power cords from the power supplies in your server to completely power off the server.

3-9

Cisco UCS C220 M4 Server Installation and Service Guide

OL-32473-01

Chapter 3 Maintaining the Server

Preparing for Server Component Installation

Removing and Replacing the Server Top Cover

Step 1 Remove the top cover (see Figure 3-4).

a. If the cover latch is locked, use a screwdriver to turn the lock 90-degrees counterclockwise to unlock

it. See Figure 3-4.

b. Lift on the end of the latch that has the green finger grip. The cover is pushed back to the open

position as you lift the latch.

c. Lift the top cover straight up from the server and set it aside.

Step 2 Replace the top cover:

Note The latch must be in the fully open position when you set the cover back in place, which allows

the opening in the latch to sit over a peg that is on the fan tray.

a. With the latch in the fully open position, place the cover on top of the server about one-half inch

(1.27 cm) behind the lip of the front cover panel. The opening in the latch should fit over the peg

that sticks up from the fan tray.

b. Press the cover latch down to the closed position. The cover is pushed forward to the closed position

as you push down the latch.

c. If desired, lock the latch by using a screwdriver to turn the lock 90-degrees clockwise.

Figure 3-4 Removing the Top Cover

1Top cover 2Locking cover latch

353091

3-10

Cisco UCS C220 M4 Server Installation and Service Guide

OL-32473-01

Chapter 3 Maintaining the Server

Preparing for Server Component Installation

Serial Number Location

The serial number for the server is printed on a label on the top of the server, near the front.

Hot-Swap or Hot-Plug Replacement

Some components can be removed and replaced without powering off and removing AC power from the

server. This type of replacement has two varieties: hot-swap and hot-plug.

•Hot-swap replacement—You do not have to precondition or shut down the component in the

software before you remove it for the following components:

–

SAS/SATA drives

–

Cooling fan modules

–

Power supplies (when 1+1 redundant)

•Hot-plug replacement—You must take the component offline before removing it for the following

component:

–

NVMe PCIE SSD drives

Otros manuales para UCS C220 M4

Tabla de contenidos

Otros manuales de Servidor de Cisco

Cisco

Cisco UCS C200 Instrucciones de instalación y mantenimiento

Cisco

Cisco VCS Series Manual de usuario

Cisco

Cisco Firepower Management Center 750 Manual de usuario

Cisco

Cisco UCS C240 M4 Instrucciones de instalación y mantenimiento

Cisco

Cisco C460 M4 Manual de usuario

Cisco

Cisco SFS 7008P Instrucciones de funcionamiento y mantenimiento

Cisco

Cisco Meraki MX65 Manual de usuario

Cisco

Cisco APIC M3 Instrucciones de instalación y mantenimiento

Cisco

Cisco UCS C22 Instrucciones de instalación y mantenimiento

Cisco

Cisco TelePresenceMCU 5300 Series Manual de usuario

Cisco

Cisco C880 M5 Manual de usuario

Cisco

Cisco AS5200 - Universal Access Server Manual de usuario

Cisco

Cisco TelePresence Manual de servicio

Cisco

Cisco UCS C220 M4 Instrucciones de instalación y mantenimiento

Cisco

Cisco UCS C Series Manual de usuario

Cisco

Cisco UCS C200 M2 Manual del sistema

Cisco

Cisco MSE 3365 Manual de usuario

Cisco

Cisco UCS B200 M4 Manual

Cisco

Cisco UCS B440-M1 Guía rápida

Cisco

Cisco UCS C480 M5 Instrucciones de instalación y mantenimiento

Cisco

Cisco GSS-4492R-K9 Manual de instrucciones

Cisco

Cisco C880 M5 Manual de usuario

Cisco

Cisco UCS C220 M3 Manual de usuario

Cisco

Cisco UCS M3 Series Manual de usuario

Manuales populares de Servidor de otras marcas

HP AlphaServer ES47 Manual de usuario

Dell

Dell PowerEdge R410 Manual de usuario

PowerNAS

PowerNAS CMA Manual de usuario

Supero

Supero FatTwin F617R3-FT Manual de usuario

MSI

MSI P1-109N-L70 Manual de usuario

Dell

Dell PowerEdge XE9640 Manual

Dell

Dell PS4100 Instrucciones de montaje

EtroVISION

EtroVISION EV3151 Manual de usuario

NEC

NEC Express5800/T110j Manual de usuario

HP ProLiant Gen9 Manual de usuario

Compaq

Compaq ProLiant 3000 Manual

Dell

Dell PowerEdge 3YPMN Manual de usuario

iRobo

iRobo IPC2U Manual de usuario

Nortel

Nortel 1000 Con?guration guide Manual de usuario

Asus

Asus AP7500 Manual de operación y mantenimiento

Avid Technology

Avid Technology AirSpeed 5000 Manual de usuario

HP Integrity rx2600 Guía de instalación

Milestone

Milestone Husky IVO 350T Manual de usuario