Cisco 5100 Manual de usuario

Preparing for Installation

•Safety Recommendations and Warnings, on page 1

•Safety with Electricity, on page 2

•Site Requirements, on page 3

•Mounting Requirements, on page 4

•Power Guidelines and Requirements, on page 5

•Network Cabling Specification, on page 5

•Required Tools and Equipment, on page 5

Safety Recommendations and Warnings

Review the safety warnings listed in Regulatory Compliance and Safety Information for the Cisco 5100

Enterprise Network Compute System before installing, configuring, or maintaining the device.

Please read the following safety guidelines before you install this product:

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work

on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard

practices for preventing accidents. Use the statement number provided at the end of each warning to locate

its translation in the translated safety warnings that accompanied this device. Statement 1071

Warning

Read the installation instructions before you connect the system to its power source. Statement 1004

Warning

Ultimate disposal of this product should be handled according to all national laws and regulations. Statement

1040

Warning

Installation of the equipment must comply with local and national electrical codes. Statement 1074

Warning

Preparing for Installation

Always follow these electrostatic discharge (ESD) prevention procedures when removing and replacing

modules:

• Ensure that the chassis is electrically connected to ground.

• Wear an ESD-preventive wrist strap, ensuring that it makes good skin contact. Connect the clip to an

unpainted surface of the chassis frame to channel unwanted ESD voltages safely to ground. To guard

against ESD damage and shocks, the wrist strap and cord must operate effectively.

• If no wrist strap is available, ground yourself by touching a metal part of the chassis.

For the safety of your equipment, periodically check the resistance value of the anti-static strap. It should be

between 1 and 10 megohms (Mohm).

Note

Safety with Electricity

Follow these general guidelines when working on equipment that is powered by electricity:

• Locate the emergency power-off switch in the room in which you are working. If an electrical accident

occurs, you can quickly turn off the power.

• Disconnect all power before doing the following:

• Installing or removing a chassis.

• Working near power supplies.

• Look carefully for possible hazards in your work area, such as moist floors, ungrounded power extension

cables, frayed power cords, and missing safety grounds.

• Do not work alone if hazardous conditions exist.

• Never assume that power is disconnected from a circuit. Always check.

• Never open the enclosure of the internal power supply.

• If an electrical accident occurs, proceed as follows:

• Turn off power to the device.

• Call for help.

•Determine if the person needs rescue breathing or external cardiac compressions; then take appropriate

action.

Follow these guidelines when working with any equipment that is disconnected from a power source but is

still connected to telephone wiring or other network cabling:

• Never install telephone wiring during a lightning storm.

• Never install telephone jacks in wet locations unless the jack is specifically designed for it.

Preparing for Installation

Safety with Electricity

• Never touch uninsulated telephone wires or terminals unless the telephone line is disconnected at the

network interface.

• Use caution when installing or modifying telephone lines.

• Remove power cables from all installed power supplies before opening the chassis.

Always follow these electrostatic discharge (ESD) prevention procedures when removing and replacing

modules:

• Ensure that the router chassis is electrically connected to ground.

• Wear an ESD-preventive wrist strap, ensuring that it makes good skin contact. Connect the clip to an

unpainted surface of the chassis frame to channel unwanted ESD voltages safely to ground. To guard

against ESD damage and shocks, the wrist strap and cord must operate effectively.

• If no wrist strap is available, ground yourself by touching a metal part of the chassis.

For the safety of your equipment, periodically check the resistance value of the anti-static strap. It should be

between 1 and 10 megohms (Mohm).

Caution

Site Requirements

Follow the general precautions listed below when installing or working with your device:

• Do not block cooling vents.

• Route system cables, and the power supply cable and plug so that they cannot be stepped on or tripped

over. Be sure that nothing else rests on your system component cables or power cable.

• If you turn off your system, wait at least 30 seconds before turning it on again to avoid system component

damage.

•

This product relies on the building’s installation for short-circuit (overcurrent)

protection. Ensure that the protective device is rated not greater than: 20A

Statement 1005

Warning

•

To prevent the system from overheating, do not operate it in an area that exceeds

the maximum recommended ambient temperature of: 40 degrees C. Statement

1047

Warning

Temperature, humidity, altitude, and vibration can affect the performance and reliability of the chassis. After

installation, ensure that the site maintains the environmental characteristics shown in this table:

Preparing for Installation

Site Requirements

MaximumMinimumEnvironmental Characteristic

40 degree C

(40 degrees C at 10,000

feet)

0 degree CSteady State Operating

+70 degrees C-20 degrees CStorage

90%10%Humidity operating (noncondensing)

95%5%Humidity nonoperating (noncondensing)

10,000 feet-500 feetAltitude operating: over allowable temperature range

(0 to 40 degrees C)

50,000 feet-1000 feetAltitude, nonoperating: over allowable temperature

range

+70 degrees C-25 degrees CThermal shock non-operating with change over time

of 3 minute

+40 degrees C0 degrees CThermal Shock - Operating at 2.5 degree C per minute

Mounting Requirements

The height, width, depth and weight of the chassis are displayed in this table:

MeasurementCharacteristic

1.73 inches (4.39 cm) — 1RU rack-mountHeight

12.70 inches (32.258 cm)Width

10.0 inches (25.4 cm)Depth

6.6 lbs. (2.99 kg)Weight

To place the system in a proper location, it is necessary to know the dimensions of the device's chassis.

The Cisco 5100 ENCS can be placed on a desktop or installed in a rack. The mounting ears for the device are

designed for #12-24 UNC screws.

The location of your device and the layout of your equipment rack or wiring room are extremely important

considerations for proper operation. Equipment placed too close together, inadequate ventilation, and

inaccessible panels can cause malfunctions and shutdowns, and can make maintenance difficult. Plan for

access to both front and rear panels of the device.

This information can help you plan the rack configuration for your equipment:

• Allow clearance around the rack for maintenance.

• Allow at least one rack unit of vertical space between devices.

Preparing for Installation

Mounting Requirements

•Enclosed racks must have adequate ventilation. Ensure that the rack is not congested, because each device

generates heat. An enclosed rack should have louvered sides and a fan to provide cooling air. Heat

generated by equipment near the bottom of the rack can be drawn upward into the intake ports of the

equipment above it.

• When mounting a chassis in an open rack, ensure that the rack frame does not block the intake or exhaust

ports. If the chassis is installed on slides, check the position of the chassis when it is seated in the rack.

Power Guidelines and Requirements

Check the power at your site to ensure that you are receiving "clean" power (free of spikes and noise). Install

a power conditioner if necessary.

The AC power supply supports either 110V or 220V operation. All units include a 6-foot (1.8-meter) electrical

power cord.

Network Cabling Specification

• Ethernet cables for RJ45 ports

• Serial or console cables used to connect devices like routers

• Shielded USB cables with properly terminated shields for the USB port

Required Tools and Equipment

You will need the following equipment to install the device and its equipment:

• ESD-preventive cord and wrist strap

• Phillips screwdrivers: small, 3/16-in. (4 to 5 mm), and medium, 1/4-in. (6 to 7 mm)

• Screws that fit your rack

• Wire crimper for chassis grounding - to be used along with the ground lug kit

• One 14 AWG cable for the ground lug kit

In addition, depending on the type of modules you plan to use, you might need the following equipment to

connect a port to an external network

• Cables for connection to the WAN and LAN ports (dependent on the configuration)

If you order the required cables when you purchase the device, the cables ship

along with the product.

Note

Preparing for Installation

Power Guidelines and Requirements

Preparing for Installation

Required Tools and Equipment

Otros manuales para 5100

Tabla de contenidos

Otros manuales de Servidor de Cisco

Cisco

Cisco UCS B200 M3 Manual

Cisco

Cisco UCS C460 M2 Manual de usuario

Cisco

Cisco N20-B6625-1 Manual del sistema

Cisco

Cisco SNS-3515 series Manual de usuario

Cisco

Cisco TelePresence Server 7010 Manual de usuario

Cisco

Cisco UCS B200 Manual

Cisco

Cisco UCS C220 M4 Manual de usuario

Cisco

Cisco TelePresence Video Communication Server Manual de servicio

Cisco

Cisco UCS C220 Instrucciones de instalación y mantenimiento

Cisco

Cisco UCS B440 M2 Manual del sistema

Cisco

Cisco UCS B420 M3 Manual de instalación y operación

Cisco

Cisco ONS 15600 Manual de usuario

Cisco

Cisco UCS C220 M4 Guía de inicio rápido

Cisco

Cisco TelePresence MSE 8710 Manual de usuario

Cisco

Cisco AS5300 - Universal Access Server Documento técnico

Cisco

Cisco UCS B460 M4 Manual de usuario

Cisco

Cisco UCS C220 M3 Instrucciones de instalación y mantenimiento

Cisco

Cisco UCS C250 Instrucciones de instalación y mantenimiento

Cisco

Cisco VCS Series Manual de usuario

Cisco

Cisco UCS C Series Manual

Cisco

Cisco C880 M5 Manual de usuario

Cisco

Cisco SCE2020-4XGBE-SM Manual de usuario

Cisco

Cisco TD 92322GB Manual de usuario

Cisco

Cisco UCS Invicta C3124SA Manual

Manuales populares de Servidor de otras marcas

HP AlphaServer ES47 Manual de usuario

Dell

Dell PowerEdge R410 Manual de usuario

PowerNAS

PowerNAS CMA Manual de usuario

Supero

Supero FatTwin F617R3-FT Manual de usuario

MSI

MSI P1-109N-L70 Manual de usuario

Dell

Dell PowerEdge XE9640 Manual

Dell

Dell PS4100 Instrucciones de montaje

EtroVISION

EtroVISION EV3151 Manual de usuario

NEC

NEC Express5800/T110j Manual de usuario

HP ProLiant Gen9 Manual de usuario

Compaq

Compaq ProLiant 3000 Manual

Dell

Dell PowerEdge 3YPMN Manual de usuario

iRobo

iRobo IPC2U Manual de usuario

Nortel

Nortel 1000 Con?guration guide Manual de usuario

Asus

Asus AP7500 Manual de operación y mantenimiento

Avid Technology

Avid Technology AirSpeed 5000 Manual de usuario

HP Integrity rx2600 Guía de instalación

Milestone

Milestone Husky IVO 350T Manual de usuario