Cisco SG 300-10P Manual de usuario

Cisco Ethernet Switch Quick Setup Guide

For MuxLab AV over IP Devices

Cisco Ethernet Switch Quick Setup Guide

Contents

Introduction ...............................................................................................................31.

MuxLab Ethernet Switch Setup Requirements..........................................................32.

Ethernet Switch Setup...............................................................................................43.

3.1. Enabling IGMP...............................................................................................4

3.2. Enabling Jumbo Frames................................................................................8

Preparing for System Installation ..............................................................................94.

Cisco Ethernet Switch Quick Setup Guide

Introduction1.

This document covers the basic setup requirements for a Cisco Ethernet Switch. The

setup examples and screen shots shown are for the Cisco model SG300-10P, but these

instructions are similar and applicable to other Cisco Ethernet Switch models.

MuxLab Ethernet Switch Setup Requirements2.

All MuxLab AV over IP Transmitters and Receivers require IGMP support to be enabled

on the Ethernet Switch, and a select number of MuxLab units also require Jumbo

Frames to be enabled.

Also note that all models below work on a 1G Ethernet Switch, except for the 500760,

which requires a 10G Ethernet Switch.

The below table specifies the IGMP and Jumbo Frames requirement per MuxLab AV

over IP Transmitter / Receiver model.

AV over IP

Model

Ethernet Switch

BW Required

IGMP

Required

Jumbo Frame

Required

500752

500753

500754

500755

500755-AMP

500756

500757

500758

500759

500760

10G

500762

500770

500771

Cisco Ethernet Switch Quick Setup Guide

Ethernet Switch Setup3.

3.1. Enabling IGMP

Follow the steps below to enable the IGMP feature on the Ethernet Switch. For further

details on navigating through the Ethernet Switch web server menus, please refer to the

Ethernet Switch manual.

Step 1: Access the Ethernet Switch web server

-Locate the Ethernet Switch default IP address

-Make sure your computer is on the same subnet as the Ethernet Switch

(your network administration can assist you with this, if required)

-Enter the Ethernet Switch IP address into a browser

Step 2: IGMP Snooping Configuration

-Navigate to the menu:

[Multicast →Properties]

-Set the configuration as shown below, and then click [Apply]

Cisco Ethernet Switch Quick Setup Guide

-Navigate to the menu:

[Multicast →IGMP Snooping]

-(a) Enable the “IGMP Snooping Status” as shown below, and then click [Apply]

Cisco Ethernet Switch Quick Setup Guide

-(b) Select the radio button as shown below, and click [Edit]

Cisco Ethernet Switch Quick Setup Guide

-(c) Set the configuration as shown below, and then click [Apply]

Step 3: Save the above configuration changes

-Navigate to the menu:

[Administration →File Management →Copy/Save Configuration]

-Click on [Apply] as shown below

Cisco Ethernet Switch Quick Setup Guide

3.2. Enabling Jumbo Frames

Follow the steps below to enable the Jumbo Frames feature on the Ethernet Switch. For

further details on navigating through the Ethernet Switch web server menus, please

refer to the Ethernet Switch manual.

Step 1: Enable Jumbo Frames

-Navigate to the menu:

[Port Management > Port Settings]

-Check the “Jumbo Frame” checkbox as shown below, then click [Save]

Step # 2: Save the above configuration changes

-Navigate to the menu:

[Administration > File Management > Copy/Save Configuration]

-Click on [Apply]

Cisco Ethernet Switch Quick Setup Guide

Preparing for System Installation4.

The Ethernet Switch is now properly configured to support MuxLab AV over IP devices

with respect to IGMP and Jumbo Frames.

Note that MuxLab AV over IP Transmitters and Receivers are set by default with DHCP

enabled, and the MuxLab 500811 ProDigital Network Controller has DHCP disabled by

default and is set to a Static IP address of 192.168.168.50. It is recommended that you

operate your system with the Transmitters and Receivers with DHCP enable and the

500811 Network Controller with DHCP disabled.

If however you intend to disable the DHCP on the Transmitters and Receivers, then

please take note that the default Static IP address for the Transmitters is

192.168.168.55, and for the Receivers is 192.168.168.56.

Note that in order for the entire system to operate correctly, the Ethernet Switch,

MuxLab Transmitters and Receivers, and the MuxLab ProDigital Network Controller

must all be on the same subnet. Devices with DHCP enabled will adjust automatically to

the correct subnet, while devices with DHCP disabled, may need to be set by the user to

the correct subnet, if not already set correctly. Your network administrator can assist with

this configuration if you are not familiar with how to accomplish this task.

If you are having issues which require further assistance, please contact the respective

device manufacturer for the device in question. For MuxLab device related questions,

please contact MuxLab Customer Technical Support at 877-689-5228 (toll-free in North

America) or (+1) 514-905-0588 (International).

Cisco Ethernet Switch Quick Setup Guide

8495 Dalton Road, Mount Royal, Quebec, Canada. H4T 1V5

Tel: (514) 905-0588

Fax: (514) 905-0589

Toll Free (North America): (877) 689-5228

E-mail: videoease@muxlab.com URL:

www.muxlab.com

Tabla de contenidos

Otros manuales de Enrutador de red de Cisco

Cisco

Cisco WS-C2950-24 Manual de usuario

Cisco

Cisco WS-X3011 Guía de inicio rápido

Cisco

Cisco CGR 1120 Manual de usuario

Cisco

Cisco QuickVPN - PC Manual de instrucciones

Cisco

Cisco 3600 Series Guía de inicio rápido

Cisco

Cisco SRW208MP Manual de usuario

Cisco

Cisco RV016 - Small Business - 10/100 VPN Router Manual de usuario

Cisco

Cisco 7609 Manual de usuario

Cisco

Cisco ASR 1000 Series Manual

Cisco

Cisco CGR2010 Guía de inicio rápido

Cisco

Cisco 3640 Series Manual de usuario

Cisco

Cisco SOHO 97 Manual de usuario

Cisco

Cisco 15216 EDFA2 Manual de usuario

Cisco

Cisco MGX 8850 (PXM1E/PXM45) Manual de usuario

Cisco

Cisco Blower Module 10000 ESR Manual de usuario

Cisco

Cisco CVR100W Manual de usuario

Cisco

Cisco 1760 - VPN Bundle Router Manual de usuario

Cisco

Cisco BPX-8620 Instrucciones de funcionamiento y mantenimiento

Cisco

Cisco uBR924 Manual de instalación

Cisco

Cisco 2800 Series Manual de referencia

Cisco

Cisco Cable Mgmt Bracket Cisco 7513/7576 Manual de usuario

Cisco

Cisco 3825 - Voice Bundle Router Instrucciones de funcionamiento

Cisco

Cisco ASR 901S Series Hoja de instrucciones

Cisco

Cisco 3200 Series Manual de instalación y operación

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

EnGenius

EnGenius ESR-9710 Manual de usuario

LevelOne

LevelOne FBR-1416 Manual de usuario

Dynacord

Dynacord Promatrix 6000 Manual de usuario

Lorex

Lorex F5D8230-4 Manual de usuario