Cisco RV345 Manual de usuario

Quick Start Guide

Cisco RV345/RV345P Router

Package Contents

•Cisco RV345/RV345P Router

•Universal Power Adapter

•Ethernet Cable

•This Quick Start Guide

•Pointer Card

•Technical Support Contact Card

•Console RJ-45 Cable

2 Cisco RV345/RV345P Router Quick Start Guide

Welcome

The Cisco RV345/RV345P series of routers provide reliable Internet

access connectivity for small businesses. All of the Cisco RV345/RV345P

series models support two connections to one Internet service provider,

delivering high performance by using load balancing, or to two different

providers to deliver business continuity.

•Dual Gigabit Ethernet WAN ports allow load balancing and business

continuity.

•Affordable, high-performance Gigabit Ethernet ports enable rapid

transfer of large files, supporting multiple users.

•Dual USB ports support a 3G/4G modem or flash drive. The WAN can

also fail over to the 3G/4G modem connected to the USB port.

•SSL VPN and site-to-site VPN enable highly secure connectivity.

•Stateful packet inspection (SPI) firewall and hardware encryption

provide strong security.

•The RV345 model has a 16-port LAN switch.

•The RV345P model has a 16-port LAN switch of which the first 8 ports

(LAN 1 - 4 and 9 - 12) are PSE (PoE) ports.

•This Quick Start Guide describes how to install your Cisco RV345/

RV345P and launch the web-based Device Manager.

Installing the Cisco RV345/RV345P

To prevent the device from overheating or being damaged:

• Ambient Temperature—Do not operate the device in an area that

exceeds an ambient temperature of 104°F (40°C).

•AirFlow—Be sure that there is adequate airflow around the device. If

wall mounting the firewall, make sure that the heat dissipation holes are

to the side.

• Circuit Overloading—Adding the device to the power outlet must not

overload that circuit.

• Mechanical Loading—Make sure that the device is level, stable and

secured to avoid any hazardous conditions and prevent it from sliding

or shifting out of position. Do not place anything on top of the firewall,

as the excessive weight may damage it.

Cisco RV345/RV345P Router Quick Start Guide 3

Rack Mounting

Your Cisco RV345/RV345P device includes a rack-mount kit that contains:

•Two rack-mount brackets

•Eight M4*6L (F) B-ZN #2 screws

4 Cisco RV345/RV345P Router Quick Start Guide

Cisco RV345/345P Features

Front Panel

PWR Off when the device is powered off.

Solid green when the device is on.

Flashing green when the device is booting up or

upgrading the firmware.

Fast flashing green when the device is running

on a bad image.

LINK/ACT of

WAN1, WAN2 and

LAN1-16

Off when there is no Ethernet connection.

Solid green when the GE Ethernet link is on.

Flashing green when the GE is sending or

receiving data.

GIGABIT of WAN1,

WAN2 and LAN1-

Solid green when at 1000M speed.

Off when at non-1000M speed.

Right LED in RJ45

(Only for the

RV345P PSE Ports)

Solid amber when PD is detected.

Off when no PD is detected.

VPN Off when no VPN tunnel is defined, or all defined

VPN tunnels have been disabled.

Solid green when at least one VPN tunnel is up.

Flashing green when sending or receiving data

over VPN tunnel.

Solid amber when no enabled VPN tunnel is up.

Cisco RV345/RV345P Router Quick Start Guide 5

NOTE For the RV345 and RV345P, LEDs are built into the magnetic jacks

for the LAN and WAN Ethernet ports. The left is the LINK/ACT and the

right is GIGABIT.

Back Panel

POWER—Toggles power to the device on or off.

12VDC (2.5A) or 54VDC (2.78A)—Power port that connects the device to

the provided 12VDC, 2.5 or 54VDC 2.78 amp power adapter.

Console Port—The router console port is designed for a serial cable

connection to a terminal or a computer that is running a terminal emulation

program.

Side Panel

USB 2—Type A USB port that supports flash drives and 3G/4G/LTE USB

dongles. Caution: Use only the power supply provided with the device;

using other power supplies may cause the USB dongle to fail.

Kensington Lock Slot - Lock slot on the right side to secure the device

physically, using the Kensington lock-down equipment.

USB 1 and USB 2 Off when no USB device is connected, or is

inserted but not recognized.

Solid green when the USB dongle is connected

to the ISP successfully. (IP address has been

assigned); USB storage is recognized.

Flashing green when sending or receiving data.

Solid amber when the USB dongle is recognized

but fails to connect to ISP (no IP address is

assigned). The USB storage access has errors.

Reset •To reboot the router, press the reset button

with a paper clip or pen tip for less than 10

seconds.

•To reset the router to factory default settings,

press and hold the reset button for 10

seconds.

6 Cisco RV345/RV345P Router Quick Start Guide

Connecting the Equipment

Connect a configuration terminal (PC) to the device by using a LAN port.

The terminal must be in the same wired subnetwork as the device to

perform the initial configuration. As part of the initial configuration, the

device can be configured to allow remote management.

To connect a computer to the device:

STEP 1Power off all equipment, including the cable or DSL modem, the

computer, and this device.

STEP 2Use an Ethernet cable to connect your cable or DSL modem to the

WAN port on this device.

STEP 3Connect another Ethernet cable from one of the LAN (Ethernet)

ports to the Ethernet port on the computer.

STEP 4Power on the WAN device and wait until the connection is active.

STEP 5Connect the power adapter to the 12VDC or 54VDC port of the

device.

CAUTION Use only the power adapter that is supplied with the device.

Using a different power adapter could damage the device or

cause the USB dongles to fail.

The power switch is on by default. The power light on the front

panel is solid green when the power adapter is connected

properly and the device is finished booting.

STEP 6Plug the other end of the adapter into an electrical outlet. Use the

plug (supplied) specific to your country.

STEP 7Continue with the instructions in the Using the Setup Wizard to

configure the device.

Cisco RV345/RV345P Router Quick Start Guide 7

Using the Setup Wizard

The Setup Wizard and Device Manager are supported on Microsoft

Internet Explorer, Mozilla Firefox, Apple Safari, and Google Chrome.

To configure the device using the Setup Wizard, follow these steps:

STEP 1Power on the PC that you connected to the LAN1 port in Step 3 of

the Connecting Equipment section. Your PC becomes a DHCP

client of the device and receives an IP address in the 192.168.1.xxx

range.

STEP 2Launch a web browser.

STEP 3In the address bar, enter the default IP address of the device,

https://192.168.1.1. A site security certificate message is

displayed. The Cisco RV345/RV345P uses a self-signed security

certificate. This message appears because the device is not

known to your computer.

STEP 4Click Continue to this website to continue. The sign-in page

appears.

STEP 5Enter the username and password. The default username is cisco.

The default password is cisco. Passwords are case-sensitive.

STEP 6Click Log In. The Router Setup Wizard is launched.

STEP 7Follow the on-screen instructions to set up your device. The Router

Setup Wizard should detect and configure your connection. If it is

unable to do so, it asks you for information about your internet

connection. Contact your ISP for this information.

STEP 8Change the password as instructed by the Router Setup Wizard or

follow the instructions in the Changing the Administrator Username

and Password section. Log in to the device with the new username

and password.

NOTE We recommend that you change the password. You are

required to change the password before enabling features such as

remote management.

The Device Manager Getting Started page appears. It displays the

most common configuration tasks.

STEP 9Click one of the tasks listed in the navigation bar to complete the

configuration.

444

8 Cisco RV345/RV345P Router Quick Start Guide

STEP10 Save any additional configuration changes and log out of the

device manager.

Changing the Administrator Username and Password

To change the Administrator username and password on the device:

STEP 1From the Getting Started page, select Change Administrator

Password or select System Configuration > User Accounts from

the navigation bar.

STEP 2Check a username from the Local User Membership list and click

Edit.

STEP 3Enter the Username.

STEP 4Enter the Password.

STEP 5Confirm the Password.

STEP 6Check Group (admin, oper, test-group) in the Password Strength

Meter.

STEP 7Click Save.

Troubleshoot Your Connection

If you cannot access your device by using the Setup Wizard, the device

may not be reachable from your computer. You can test network

connections by using ping on a computer running Windows:

STEP 1Open a command window by using Start > Run and enter cmd.

STEP 2At the Command window prompt, enter ping and the device IP

address. For example, ping 192.168.1.1 (the default static IP

address of the device).

If you can reach the device, you should get a reply similar to the

following:

Pinging 192.168.1.1 with 32 bytes of data:

Reply from 192.168.1.1: bytes=32 time<1ms TTL=128

If you cannot reach the device, you should get a reply similar to the

following:

Pinging 192.168.1.1 with 32 bytes of data:

Request timed out.

Cisco RV345/RV345P Router Quick Start Guide 9

Possible Causes and Resolutions

Bad Ethernet connection:

Check the LEDs for the proper indications. Check the connectors of the

Ethernet cable to ensure that they are firmly plugged into the device

and your computer.

Wrong or conflicting IP address:

Verify that you are using the correct IP address of the device.

Verify that no other device is using the same IP address as this device.

No IP route:

If the router and your computer are in different IP subnetworks, remote

access must be enabled. You need at least one router on the network

to route the packets between the two subnetworks.

Unusually long access time:

Adding new connections may take 30–60 seconds for the affected

interfaces and LAN to become operational.

10 Cisco RV345/RV345P Router Quick Start Guide

Where to Go From Here

For EU Lot 26 related test results, see www.cisco.com/go/eu-lot26-results

Support

Cisco Support

Community

www.cisco.com/go/smallbizsupport

Cisco Support and

Resources

www.cisco.com/go/smallbizhelp

Phone Support Contacts www.cisco.com/en/US/support/

tsd_cisco_small_business

_support_center_contacts.html

Cisco Firmware

Downloads

www.cisco.com/go/smallbizfirmware

Select a link to download firmware for Cisco

products. No login is required.

Cisco Open Source

Request

www.cisco.com/go/

smallbiz_opensource_request

Cisco Partner Central

(Partner Login Required)

www.cisco.com/web/partners/sell/smb

Product Documentation

Cisco RV345/RV345P www.cisco.com/go/RV345/RV345P

Otros manuales para RV345

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Enrutador de red de Cisco

Cisco

Cisco ASR 900 Series Manual de usuario

Cisco

Cisco Linksys E1200 Instrucciones de uso

Cisco

Cisco Linksys WRT54GS Instrucciones de funcionamiento originales

Cisco

Cisco 7600-SIP-400 - SPA Interface Processor 400 Manual de usuario

Cisco

Cisco 2612 Manual de usuario

Cisco

Cisco Small Business RV215W Manual de instrucciones

Cisco

Cisco Universal Broadband Router Cisco uBR10012 Manual de usuario

Cisco

Cisco ASR 5000 Series Instrucciones de funcionamiento y seguridad

Cisco

Cisco Network Convergence System 6000 Series Manual de usuario

Cisco

Cisco vEdge 100b Manual de usuario

Cisco

Cisco OL-4387-02 Manual de usuario

Cisco

Cisco 12008 Manual del operador

Cisco

Cisco Linksys X2000 V2 Manual de usuario

Cisco

Cisco IR829 Manual

Cisco

Cisco 12000 - Series Chassis Modular Expansion... Manual

Cisco

Cisco NCS 4000 Series Manual de usuario

Cisco

Cisco Linksys ATA Manual de usuario

Cisco

Cisco 805 Series Manual de usuario

Cisco

Cisco XR 12000 Manual

Cisco

Cisco 1005 Guía de instalación

Cisco

Cisco 3200 Series Manual de instalación y operación

Cisco

Cisco 1750 Manual

Cisco

Cisco Linksys WRK54G Manual de usuario

Cisco

Cisco WS-C3550-12G Manual de usuario

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

EnGenius

EnGenius ESR-9710 Manual de usuario

LevelOne

LevelOne FBR-1416 Manual de usuario

Dynacord

Dynacord Promatrix 6000 Manual de usuario

Lorex

Lorex F5D8230-4 Manual de usuario