Cisco Catalyst 3560-CX Instrucciones de funcionamiento y seguridad
Product Overview
The Catalyst 3560-CX and 2960-CX switches are Ethernet switches to which you can connect devices such
as Cisco IP Phones, Cisco Wireless Access Points, workstations, and other network devices such as servers,
routers, and other switches.
You can deploy these switches outside of the traditional wiring closet environment, such as in office
workspaces, hotel rooms, slot machines, kiosks, and classrooms. The switch is suitable for deployments
where there are space and power constraints (access to power outlets).
See the switch software configuration guide for deployment examples.
This chapter contains these topics:
•Switch Models, page 1
•Front Panel, page 2
•Rear Panel, page 9
•Management Options, page 13
•Network Configurations, page 14
Switch Models
Table 1: Catalyst 3560-CX and 2960-CX Switch Models and Descriptions
DescriptionSoftware
Image
Switch Model
8 10/100/1000 Power over Ethernet plus (PoE+) ports (PoE budget of
240 W); 2 Gigabit Ethernet and 2 small form-factor pluggable (SFP)1
module uplink slots.
IP BaseWS-3560CX-8PC-S
8 10/100/1000 Ethernet ports; 2 Gigabit Ethernet and 2 small form-factor
pluggable (SFP) module uplink slots.
IP BaseWS-3560CX-8TC-S
12 10/100/1000 PoE+ ports (PoE budget of 240 W); 2 Gigabit Ethernet
and 2 SFP module uplink slots.
IP BaseWS-3560CX-12PC-S
Catalyst 3560-CX and 2960-CX Switch Hardware Installation Guide
1
DescriptionSoftware
Image
Switch Model
12 10/100/1000 Ethernet ports; 2 Gigabit Ethernet and 2 SFP module
uplink slots.
IP BaseWS-3560CX-12TC-S
12 10/100/1000 PoE+ ports (PoE budget of 240 W); 2 Gigabit Ethernet
and 2 SFP+ 2module uplink slots.
IP BaseWS-3560CX-12PD-S
8 10/100/1000 PoE+ ports (PoE budget of 146W); 2 Gigabit Ethernet
uplink ports.
IP BaseWS-3560CX-8PT-S
2 Multigigabit 3100/1000/2500/5000/10000 PoE+ ports; 6 10/100/1000
PoE+ ports (PoE budget of 240 W); 2 SFP+ module uplink slots.
IP BaseWS-3560CX-8XPD-S
8 Gigabit Ethernet PoE+ ports; and 2 SFP module uplink slots.IP BaseWS-C3560CPX-8PT-S
6 Gigabit Ethernet ports; 2 multi-Gigabit Ethernet PoE+ ports; and 2
SFP+ uplink slots.
IP BaseWS-C3560CX-8PD-S
8 10/100/1000 PoE+ ports (PoE budget of 124 W); 2 Gigabit Ethernet
and 2 SFP module uplink slots.
LAN BaseWS-2960CX-8PC-L
8 10/100/1000 Ethernet ports; 2 Gigabit Ethernet and 2 SFP module
uplink slots.
LAN BaseWS-2960CX-8TC-L
1SFP = Gigabit uplink.
2SFP+ = 10-Gigabit uplink.
3Multigigabit ports support speeds of 100 Mbps, 1 Gbps, 2.5 Gbps, and 5 Gbps on Category 5e cable and up to 10 Gbps over Category 6a cabling
IP Base switches can be upgraded to IP Services with the RTU (right to use) software license.Note
Front Panel
•8 or 12 downlink Ethernet ports of one of these types:
◦10/100/1000
◦10/100/1000 PoE+
The Catalyst 3560CX-8XPD-S has 6 PoE+ ports and 2 Multigigabit PoE+ ports.Note
•Two 10/100/1000 uplink ports and two SFP or SFP+ module ports depending on the switch model.
Catalyst 3560-CX and 2960-CX Switch Hardware Installation Guide
2
Product Overview
Front Panel
•RJ-45 console port
•USB mini-Type B (console) port
•USB Type A port
•LEDs
Figure 1: Catalyst 3560CX Front Panel View
System LEDs5Mode button1
10/100/1000 PoE+ ports6USB Type A port2
10/100/1000 uplink ports7RJ-45 console port3
SFP module slots8USB mini-Type B (console) port4
Figure 2: Catalyst 3560CX-8XPD-S Front Panel View
System LEDs5Mode button1
10/100/1000 PoE+ ports6USB Type A port2
Multigigabit PoE+ ports7RJ-45 console port3
Catalyst 3560-CX and 2960-CX Switch Hardware Installation Guide
3
Product Overview
Front Panel
SFP module slots8USB mini-Type B (console) port4
PoE+ ports 1 to 6 are Gigabit Ethernet 1/0/1 to 1/0/6. The remaining ports are 10-Gigabit Ethernet 1/0/1
and 1/0/2. However, depending on the SFP type, the rightmost ports will either be 10-Gigabit Ethernet
1/0/3 and10-Gigabit Ethernet 1/0/4 or Gigabit Ethernet 1/0/7 and Gigabit Ethernet 1/0/8.
Note
PoE and PoE+ Ports
The ports provide PoE+ support for devices compliant with IEEE 802.3af, IEEE 802.3at, and ePoE and also
provide Cisco prestandard PoE support for Cisco IP Phones and Cisco Aironet Access Points.
The maximum switch power output is either 124 W or 240 W, depending on the switch mode. Intelligent
power management allows flexible power allocation across all ports.
For switches with a 124 W power budget, you can budget the PoE and PoE+:
•15.4 W of PoE output on 8 ports
•30 W of PoE+ output on 4 ports
For switches with a 240 W power budget, you can budget the PoE and PoE+:
•15.4 W of PoE output on 12 ports
•30 W of PoE+ output on 8 ports
On a per-port basis, you control whether or not a port automatically provides power when an IP phone or an
access point is connected.
The PoE ports use RJ-45 connectors with Ethernet pinouts. The maximum cable length is 328 feet (100 meters).
The 10BASE-T, 100BASE-TX, 1000BASE-T traffic requires Category 5, Category 5e, or Category 6 unshielded
twisted pair (UTP) cable. The 10BASE-T traffic can use Category 3 or Category 4 UTP cable.
Cisco intelligent power management capabilities include enhanced power negotiation, power reservation, and
per-port power policing. For information about configuring and monitoring PoE ports, see the switch software
configuration guide on Cisco.com.
The output of the PoE circuit has been evaluated as a Limited Power Source (LPS) per IEC 60950-1.Note
10/100/1000 Ports
The 10/100/1000 ports use RJ-45 connectors with Ethernet pinouts. The maximum cable length is 328 feet
(100 meters). The 10BASE-T, 100BASE-TX, 1000BASE-T traffic requires Category 5 or Category 5e twisted
pair (UTP) cable. The 10BASE-T traffic can use Category 3 or Category 4 UTP cable.
Catalyst 3560-CX and 2960-CX Switch Hardware Installation Guide
4
Product Overview
PoE and PoE+ Ports
Multigigabit ports
The Multigigabit ports can be configured to auto-negotiate multiple speeds on switch ports, and support 100
Mbps, 1 Gbps, 2.5 Gbps, and 5 Gbps speeds on Category5e cables, and up to 10 Gbps over Category6 and
Category 6A cables.
The Multigigabit ports support PoE and PoE+ for all the supported speeds and cable types. The following
table lists the cable types and speed.
10G5G2.5G1G100MbpsCable Type
N/AYesYesYesYesCategory5E
Yes (55meters)YesYesYesYesCategory6
YesYesYesYesYesCategory6A
Management Ports
The management ports connect the switch to a PC running Microsoft Windows or to a terminal server.
•RJ-45 console port (EIA/TIA-232). The RJ-45 console port connection uses an RJ-45-to-DB-9 female
cable.
•USB mini-Type B console port (5-pin connector).
If you use the USB mini-Type B console port, the Cisco Windows USB device driver must be installed on
any PC connected to the console port (for operation with Microsoft Windows). Mac OS X or Linux do not
require special drivers.
The 4-pin mini-Type B connector resembles the 5-pin mini-Type B connectors. They are not compatible. Use
only the 5-pin mini-Type B.
This illustration shows a 5-pin mini-Type B USB port.
Figure 3: USB Mini-Type B Port
With the Cisco Windows USB device driver, you can connect and disconnect the USB cable from the console
port without affecting Windows HyperTerminal operations.
The console output always goes to both the RJ-45 and the USB console connectors, but the console input is
active on only one of the console connectors at any one time. The USB console takes precedence over the
RJ-45 console. When a cable is connected into the USB console port, the RJ-45 console port becomes inactive.
Conversely, when the USB cable is disconnected from the USB console port, the RJ-45 port becomes active.
Catalyst 3560-CX and 2960-CX Switch Hardware Installation Guide
5
Product Overview
Multigigabit ports
You can use the command-line interface (CLI) to configure an inactivity timeout which reactivates the RJ-45
console if the USB console has been activated and no input activity has occurred on the USB console for a
specified time.
After the USB console deactivates due to inactivity, you cannot use the CLI to reactivate it. Disconnect and
reconnect the USB cable to reactivate the USB console. For information on using the CLI to configure the
USB console interface, see the software guide.
SFP and SFP+ Module Slots
The switch has either two 1-Gigabit SFP or 10-Gigabit SFP+ module slots. The slots marked SFP+ support
both SFP and SFP+ modules. The SFP slots support only the SFP modules.
For Cisco SFP and SFP+ modules documentation, including compatibility matrixes, refer to this URL: http:/
/www.cisco.com/en/US/products/hw/modules/ps5455/products_device_support_tables_list.html
LEDs
You can use the switch system and port LEDs to monitor switch activity and performance.
This figure shows the switch LEDs and the Mode button that you use to select a port mode.
Figure 4: Switch LEDs and Mode Button
STACK LED 4
6Mode button1
Console LED7SYST LED (system)2
Port LEDs8STAT LED (status)3
Uplink port LED (copper)9SPEED LED4
Catalyst 3560-CX and 2960-CX Switch Hardware Installation Guide
6
Product Overview
SFP and SFP+ Module Slots
Uplink port LED ( SFP/SFP+)10PoE LED 5
5
4Only on switch models that have stacking capability. Note that this release does not support switch stacking.
5Only on switch models that support PoE.
System LED
System StatusColor
System is not powered on.Off
System is operating normally.Green
System is receiving power but is not operating
properly.
Amber
System StatusColor
System is not powered on.Off
System is operating normally.Green
System is receiving power but is not operating
properly.
Amber
POST is in progress.Blinking Green
Modes for Port LEDs
The port LEDs, as a group or individually, display information about the switch and about the individual
ports.
DescriptionPort ModeLED
The port status. This is the default mode.Port statusSTAT
The port operating speed: 10, 100, or 1000
Mb/s.
Port speedSPEED
The PoE status.PoE port powerPoE
Catalyst 3560-CX and 2960-CX Switch Hardware Installation Guide
7
Product Overview
LEDs
PoE LED
Even if the PoE mode is not selected, the LED shows PoE problems when they are detected. The PoE LED
is only on the switches that support PoE.
DescriptionColor
PoE is not enabled.Off
PoE is enabled. Ports are functioning correctly.Green
•PoE mode is not selected
•At least one of the 10/100 or 10/100/100 PoE ports has been denied
power
•At least one of the ports has a PoE fault
Blinking amber
Console LEDs
The console LEDs show which console port is in use.
If you connect a cable to a console port, the switch automatically uses that port for console communication.
If you connect two console cables, the USB-mini console port has priority.
DescriptionColorLED
RJ-45 console port is active.
USB-mini console port LED is not
active.
GreenRJ-45 console port
Port is not active.
USB-mini console port is active.
Off
USB-mini console port is active.
RJ-45 console port LED is not
active.
GreenUSB-mini console port
Port is not active.
RJ-45 console port is active.
Off
Port LEDs
RJ-45 ports and SFP-module slots have port LEDs. These LEDs, as a group or individually, provide information
about the switch and about the individual ports.
Catalyst 3560-CX and 2960-CX Switch Hardware Installation Guide
8
Product Overview
LEDs
DescriptionLED Color
No link or port was administratively shut down.Off
Link present but is not sending or receiving data.Green
Activity. Port is sending or receiving data.Blinking green
Link fault. Error frames can affect connectivity, and errors such as
excessive collisions, CRC errors, and alignment and jabber errors are
monitored for link faults.
Alternating green-amber
Port is blocked by Spanning Tree Protocol (STP) and is not forwarding
data. After a port is reconfigured, the port LED is amber for up to 30
seconds as STP searches for loops.
Amber
Rear Panel
•A security slot
•An AC power connector or a power adapter connector (on Catalyst 3560CX-8PT-S only)
•A loop (for the optional power cord retainer)
Catalyst 3560-CX and 2960-CX Switch Hardware Installation Guide
9
Product Overview
Rear Panel
•Heat sink fins (PoE models only)
Figure 5: Rear Panel of a Non-PoE Switch
Figure 6: Rear Panel of a PoE Switch
•A security slot
•An AC power connector
•A loop (for the optional power cord retainer)
Catalyst 3560-CX and 2960-CX Switch Hardware Installation Guide
10
Product Overview
Rear Panel
Otros manuales para Catalyst 3560-CX
3
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Enrutador de red de Cisco
Cisco
Cisco 1760V Manual de usuario
Cisco
Cisco 1750 Manual de usuario
Cisco
Cisco XR 12416 Manual de usuario
Cisco
Cisco 2651 Manual de usuario
Cisco
Cisco 3600 Series Manual
Cisco
Cisco ASR 9000 Series Manual de usuario
Cisco
Cisco WIC-1ENET - 1700 Access Routers 1port10bt Enet Wan... Manual de usuario
Cisco
Cisco E-Series Manual de usuario
Cisco
Cisco ASR 1000 Series Manual
Cisco
Cisco Firepower 1120 Manual de usuario
Cisco
Cisco cBR Manual
Cisco
Cisco ASR 903 Manual de usuario
Cisco
Cisco CISCO10720 Instrucciones de funcionamiento y mantenimiento
Cisco
Cisco Aironet 1400 Series Manual de usuario
Cisco
Cisco Nexus 3000 series Manual de instalación
Cisco
Cisco EA-Series Manual de usuario
Cisco
Cisco Small Business RV320 Manual de instrucciones
Cisco
Cisco CSR 1000v Series Manual de usuario
Cisco
Cisco Linksys WET11 Manual de usuario
Cisco
Cisco 7201 Manual de usuario
