Cisco 805 Series Manual de usuario
CHAPTER
Installing the Cisco 805 Router 2-1
2
Installing the Cisco 805 Router
This chapter provides information on the following topics:
•Safety
•Required Equipment
•Unpacking the Box
•Installing the Router
•Where to Go Next
Safety
This section contains information on warnings associated with using your router and on
electrostatic discharge (ESD).
Warnings
Before installing the router, read the following warnings:
Warning Only trained and qualified personnel should be allowed to install or
replace this equipment.
Warning Read the installation instructions before you connect the system to its
power source.
Safety
Cisco 805 Router Hardware Installation Guide
2-2
Warning Before working on a system that has a standby/on switch, turn the
power to standby and unplug the power cord.
Warning Before working on equipment that is connected to power lines, remove
jewelry (including rings, necklaces, and watches). Metal objects will heat up when
connected to power and ground and can cause serious burns or weld the metal
object to the terminals.
Warning Ultimate disposal of this product should be handled according to all
national laws and regulations.
Warning If the symbol of suitability with an overlaid cross ( ) appears above a
port, you must not connect the port to a public network that follows the European
Union standards. Connecting the port to this type of public network can cause
severe injury or damage your router.
Warning To avoid electric shock, do not connect safety extra-low voltage
(SELV) circuits to telephone-network voltage (TNV) circuits. LAN ports contain
SELV circuits, and WAN ports contain TNV circuits. Some LAN and WAN ports
both use RJ-45 connectors. Use caution when connecting cables.
Figure 2-1 shows the Cisco 805 router ports that include SELV circuits. For a definition of
SELV and TNV, see “Terms and Acronyms” in “About this Guide.”
Installing the Cisco 805 Router 2-3
ESD
Figure 2-1 SELV Circuit Ports
ESD
ESD is a transfer of electrostatic charge between bodies of different electrostatic potentials,
such as an operator and a piece of electrical equipment. It occurs when electronic
components are improperly handled, and it can damage equipment and impair electrical
circuitry. Electrostatic discharge is more likely to occur with the combination of synthetic
fibers and dry atmosphere.
Always use the following ESD-prevention guidelines when removing and replacing
components:
•Connect the chassis to earth ground with a wire that you provide.
•Wear an ESD-preventive wrist strap that you provide, ensuring that it makes good skin
contact.
•Do not touch any exposed contact pins or connector shells of uncabled router ports.
•If cables are connected at one end only, do not touch the exposed pins at the unconnected
end of the cable.
Note This device is intended for use in residential and commercial environments only.
24848
Cisco 805
LINK
HUB
NO HUB
ETHERNET
10 BASE T
Includes
SELV circuits
SERIAL
CONSOLE
Required Equipment
Cisco 805 Router Hardware Installation Guide
2-4
Caution Periodically check the resistance value of the antistatic strap, which
should be between 1 and 10 megohms (Mohms).
Required Equipment
You need to provide the following equipment:
•The hub, server, workstation, or PC that you plan to connect to the Ethernet port. The
server, workstation, or PC must have a 10- or 10/100-Mbps network interface card
(NIC).
•The asynchronous modem or channel service unit/data service unit (CSU/DSU) that you
plan to connect to the serial port.
•The serial cable that connects the router to the serial device. For information on
selecting and ordering the serial cable, refer to Appendix A, “Selecting a Serial Cable.”
•The terminal or PC with which you plan to configure the software or troubleshoot the
router.
Caution If you are mounting the router on drywall, use three hollow-wall
anchors to secure the three 1/8-in. (M3) screws. If the screws are not properly
anchored, the strain of the network cable connections could pull the router from
the wall. Use the drill bit size that is specified by the hollow-wall anchor
manufacturer.
Installing the Cisco 805 Router 2-5
Unpacking the Box
Unpacking the Box
The items that come with your router are listed below. All these items are in the accessory
kit that is inside the box that your router came in. If any of the items is missing or damaged,
contact your customer service representative.
•Power cord (black)
•Desktop power supply
•Console cable (light blue)
•DB-9-to-RJ-45 adapter for use with light blue console cable
•DB-25-to-RJ-45 adapter for use with light blue console cable
•Ethernet cable (yellow)
•Product documentation
Note A serial cable does not ship with the router. For information on selecting and
ordering the serial cable, refer to Appendix A, “Selecting a Serial Cable.”
Installing the Router
Cisco 805 Router Hardware Installation Guide
2-6
Installing the Router
To install the router, perform the following tasks in the following order:
1Connect an Ethernet device.
2Connect a serial device.
3Connect a terminal or PC (for software configuration or router troubleshooting).
4Connect the power supply.
5Mount the router.
6Verify the router installation.
Connecting an Ethernet Device
You can connect the following devices to the Ethernet port:
•A hub
•A server, PC, or workstation with a 10- or 10/100-Mbps NIC
Table 2-1 lists the Ethernet devices you can connect to the router with the yellow Ethernet
cable and the appropriate settings of the router HUB/NO HUB button and the hub
equivalent of the HUB/NO HUB button. The default setting of the router HUB/NO HUB
button is HUB (in).
Installing the Cisco 805 Router 2-7
Connecting an Ethernet Device
Connecting a Hub
Before connecting a hub, refer to Table 2-1 to determine how to set the router
HUB/NO HUB button and the hub equivalent of the HUB/NO HUB button if applicable.
Follow the steps in Figure 2-2 to connect a hub.
Table 2-1 Connecting Ethernet Devices
Network Device Connected to Router
Router HUB/NO HUB
Button Setting
Hub Button
Setting1
1 Hub vendors choose different names for the button controlling cable selection. This table uses the Cisco 1528
Micro Hub 10/100 with an MDI/MDI-X button as an example. Determine the button name and setting for
your particular hub. Refer to your hub documentation for details.
Hub with equivalent to router HUB/NO HUB
button
HUB (in) MDI (in)
Hub with equivalent to router HUB/NO HUB
button
NO HUB (out) MDI-X (out)
Hub without equivalent to router HUB/NO
HUB button
NO HUB (out) MDI-X (out)
Server, PC, or workstation NO HUB (out) –
Installing the Router
Cisco 805 Router Hardware Installation Guide
2-8
Figure 2-2 Connecting a Hub
Connecting a Server, PC, or Workstation
Before connecting the server, PC, or workstation, do the following:
•Make sure that the device has a 10- or 10/100-Mbps NIC.
•Refer to Table 2-1 to determine how to set the router HUB/NO HUB button.
Follow the steps in Figure 2-3 to connect a server, PC, or workstation.
17284
Cisco 1528 Micro Hub 10/100
Cisco 805 router
2. Connect yellow
cable to yellow
Ethernet port.
1. Set HUB/NO HUB button.
MDI MDI-X
6X 7X 8X
1X 2X 3X 4X
ETHERNET
1
SPEED
100BaseTX
10BaseT
LED
SOLID
BLINK
234
567 8
3. Connect other
end of cable
to hub. 4. If applicable, check
setting of hub
equivalent of router
HUB/NO HUB button.
Cisco 805
LINK
HUB
NO HUB
ETHERNET
10 BASE T
SERIAL
CONSOLE
Installing the Cisco 805 Router 2-9
Connecting an Ethernet Device
Figure 2-3 Connecting a Server, PC, or Workstation
Cisco 805 router
Cisco 805
LINK
HUB
NO HUB
ETHERNET
10 BASE T
SERIAL
CONSOLE
17285
PC
AUX
SER 0
OK
LAN
ETH
3. Connect other end of cable
to server, PC, or workstation.
2. Connect yellow
cable to yellow
Ethernet port.
1. Set HUB/NO HUB button.
Installing the Router
Cisco 805 Router Hardware Installation Guide
2-10
Connecting a Serial Device
You can connect any one of several serial devices to the router serial port. For more
information, see the “DTE or DCE” section in Appendix A, “Selecting a Serial Cable.”
Table 2-2 describes the devices most commonly connected to the router serial port and how
these devices are used.
Note A serial cable does not ship with the router. For information on selecting and
ordering the serial cable, refer to Appendix A, “Selecting a Serial Cable.”
Follow the steps in Figure 2-4 to connect a modem or CSU/DSU.
Caution The Cisco 805 router does not support the Australian IUT requirement,
which specifies that the router must communicate for 1/2 hour after a power
failure. If a power failure occurs, the Cisco 805 router stops communicating with
other devices.
Table 2-2 Connecting a Serial Device
Serial Device WAN Options
WAN Encapsulation
(Framing) Network Type
Asynchronous modem Asynchronous dial-up
line
Point-to-Point Protocol
(PPP)
• Remote office to corporate office
• Small office to Internet service
provider (ISP)
Channel service
unit/data service unit
(CSU/DSU)
• Synchronous leased
line
•FrameRelay
•X.25
• For synchronous leased
line: High-Level Data
Link Control (HDLC) or
PPP
• Frame Relay
•X.25
• Remote office to corporate office
• Small office to ISP
Otros manuales para 805 Series
6
Tabla de contenidos
Otros manuales de Enrutador de red de Cisco
Cisco
Cisco RV042 - Small Business Dual WAN VPN Router Manual de usuario
Cisco
Cisco 678 Instrucciones de funcionamiento
Cisco
Cisco RPM-XF Manual de usuario
Cisco
Cisco WS-C2960-24LC-S Manual de usuario
Cisco
Cisco WUMC710 Manual de usuario
Cisco
Cisco WRT54G Manual de usuario
Cisco
Cisco Linksys WRK54G Manual de usuario
Cisco
Cisco 2600 Series Manual de usuario
Cisco
Cisco WLC 5700 Series Manual de usuario
Cisco
Cisco NCS55A1 Manual
Cisco
Cisco Nexus 7000 Series Manual de instrucciones
Cisco
Cisco 2600 Series Manual
Cisco
Cisco IR1101 Manual de usuario
Cisco
Cisco Linksys WET11 Manual de usuario
Cisco
Cisco PRP-1= Manual del operador
Cisco
Cisco 850 Series Manual de usuario
Cisco
Cisco 12006 series Instrucciones de funcionamiento y seguridad
Cisco
Cisco 7507 Manual de usuario
Cisco
Cisco Router Cisco 7206 VXR Manual de usuario
Cisco
Cisco ASR 900 Series Manual de usuario
