Cisco 7100 Series Manual de usuario
PREPARE FOR INSTALLATION
RACK-MOUNT THE ROUTER
CONNECT THE ROUTER TO THE NETWORK
CONNECT THE POWER
START THE SYSTEM
1
2
3
4
5
Quick Start Guide
CISCO 7100 SERIES VPN ROUTER
18481
Cisco 7100
SERIES
1
Prepare for Installation
Note: For detailed hardware installation instructions and safety guidelines, refer to the
Cisco 7100 Series VPN Router Installation and Configuration Guide.
Warning Only trained and qualified personnel should install, replace, or service this
equipment.
Warning Read the Installation instructions before you connect the system to its
power source.
Warning This unit is intended for installation in restricted access areas. A restricted
access area is where access can only be gained by service personnel through the use of
a special tool, lock and key, or other means of security, and is controlled by the
authority responsible for the location.
1Ensure the site is set up properly and ensure your safety when installing the router:
—Lift the router safely out of the packing container.
—Ensure the power service at the site is suitable for the router you are installing.
2Check the packing slip to ensure that all the proper components are present.
3Verify that you have the required tools and parts:
—19- and 24-inch rack-mount brackets.
—Four screws for installing the router in the rack (not included).
—One double ground lug and two Phillips-head machine screws with locking washers.
—Number 2 Phillips screwdriver (not included).
—Appropriate cables to connect the router to the network and console terminal.
—Power cord (two power cords if dual power supply).
—ESD-preventive wrist strap.
2
—One grounding wire—6-AWG, 0.162-inch (4.115-mm) diameter, with approximately
0.108 inch (2.743 mm) of insulation, for a total wire diameter of approximately
0.27 inch (6.858 mm). The wire’s length is dependent on your router location and site
environment. This wire is not available from Cisco Systems; it is available from any
commercial cable vendor.
—Crimping tool large enough to accommodate the diameter of the wire receptacle on
your grounding lug.
—Wire stripper.
Prepare for Installation (continued)
3
Rack-Mount the Router
22061
Cisco 7100
SERIES
22062
0
2
Attach the Brackets to the
Router
1Locate the brackets and screws.
2Use a Phillips screwdriver to attach the
brackets on the side panels of the router
in one of the following ways:
—Front panel forward
—Rear panel forward
Note: Although these installations show
the 19-inch brackets, the procedure is the
same for the larger brackets.
Note: This procedure assumes you are
installing the router in a rack. For tabletop
installation, refer to the Cisco 7100 Series
VPN Router Installation and Configuration
Guide.
4
.Rack-Mount the Router (continued)
22064
Note: The second bracket attaches to the other side of the chassis.
The brackets can also be installed with the front panel forward.
0
2
Attach the Router to the Rack
1Locate the screws to mount the chassis
in the rack.
2Position one person to lift the chassis
into the equipment rack.
3Align the bracket holes with the
mounting holes in the equipment rack.
4Use a Phillips screwdriver to attach the
router to the equipment rack.
Warning Donottouch thepower
supply when the power cord is
connected. For systems with a
power switch, line voltages are
present within the power supply
even when the power switch is off
and the power cord is connected.
For systems without a power
switch, line voltages are present
within the power supply when the
power cord is connected.
5
Rack-Mount the Router (continued)
22065
0
2
Chassis grounding receptaces
Grounding wire
Grounding lug
Screws
Attach the Grounding Lug
Note: Before you connect power or power
onyour router,we stronglyrecommend that
you attach the grounding lug to the chassis
grounding receptacles.
1Locate the grounding lug and screws.
2Use the wire stripper to strip one end of
the 6-AWG wire approximately
0.75 inch (19.05 mm).
3Insert the 6-AWG wire into the wire
receptacle on the grounding lug.
4Use the crimping tool to carefully crimp
thewire receptaclearound thewire;this
step is required to ensure a proper
mechanical connection.
5Insert the two screws through the holes
in the grounding lug. Ensure that the
grounding lug does not interfere with
other router hardware.
6Use a Phillips screwdriver to carefully
tighten the screws until the grounding
lug is held firmly to the chassis. Do not
overtighten the screws.
7Connect the opposite end of the
grounding wire to the appropriate
grounding point at your site to ensure
an adequate chassis ground.
6
Connect the Router to the Network
ACOK
DCOK
OTF
ACOK
DCOK
OTF
RX TX
E3
RX
5
TX
E3
RX
EN
CEL CAR ALM
I
CONS
FE 0 / 0 FE
ACT
0 / 1
AUX
0
2
7140 - 2AE3
100-240Vac 50/60Hz 5-2.5A 525W
RX
EN
CEL CAR ALM
ACT
LNK
0LNK
1
PWR
SYS
RDY
SLOT 0 SLOT 1
Ethernet hub
Cisco 7100 series router
Crossover
Ethernet cable
22068
8
10BaseT/100BaseTX ports
Fast Ethernet 0/0
(RJ-45)
7654321
Connect the Fast Ethernet
Ports
The 10BaseT/100BaseTX Fast Ethernet
ports support IEEE 802.3 and IEEE 802.3u
specifications for 10-Mbps and 100-Mbps
transmission over unshielded twisted-pair
(UTP) cables. These ports support
autosensing and autonegotiation of the
proper transmission mode with an attached
device.
Note: Unless noted otherwise, all
procedures apply to any Cisco 7100 series
router.
1Attach a standard straight-through or
crossover Category 3 or Category 5
UTP cable directly to the RJ-45
receptacle on the router.
2Attach the network end of the cable to
an Ethernet hub or end station.
7
Connect the Router to the Network
(continued)
To CSU, DSU, or external
synchronous serial equipment
TD TC RD RC LB CD
TD TC RD RC LB CD
TD
EN
TC RD RC LB CD
5
I
TC RD RC LB CD
TD
22070
Strain-relief screws
Serial 1/0
Connect the T1 Ports
(Cisco 7120-4T1 only)
The four T1 ports operate at T1
(1.544-Mbps) and E1 (2.048-Mbps) speeds
Each port uses an identical 60-pin D-shell
receptacle that supports the following
interface types:
• EIA/TIA-232
• V.35
• EIA/TIA-449
• X.21
• EIA-530
1Attach the appropriate serial cable
directly to the receptacle on the router
and tighten the strain-relief screws.
2Attach the network end of the serial
cable to a DSU, CSU, DTE, or other
external synchronous serial equipment
and tighten the strain-relief screws.
8
Connect the Router to the Network
(continued)
5
I
XMTRRCVR
XMTRRCVR
EN RCLK FERF RL
AIS OOF LL
RCLK FERF RL
AIS OOF LL
22072
To T3 network
equipment
Serial 1/0 Serial 2/0
Connect the T3 Ports
The T3 port supports full-duplex operation
at T3 (45-Mbps) speeds. Use a 75-ohm
coaxial cable to connect to a T3 serial
network. Serial cables conform to
EIA/TIA-612 and EIA/TIA-613
specifications. The T3 serial ports on the
router are considered to be DTE devices.
Note: The T3 ports support several types
of integrated DSUs. For a listing of DSU
featurecompatibilities,refer toAppendix C,
“Cable Specifications,” in the Cisco 7100
Series VPN Router Installation and
Configuration Guide.
1Attach the appropriate 75-ohm coaxial
cable directly to the receptacle on the
router and tighten the strain-relief
screws.
2Attach the network end of the coaxial
cable to the external synchronous serial
equipment.
Tabla de contenidos
Otros manuales de Enrutador de red de Cisco
Cisco
Cisco ASR 9000 Series Manual de usuario
Cisco
Cisco RV130 Manual de usuario
Cisco
Cisco 826 Manual de usuario
Cisco
Cisco WRT54G Manual de usuario
Cisco
Cisco 3600 Series Manual
Cisco
Cisco WRVS4400N - Small Business Wireless-N Gigabit Security... Manual de usuario
Cisco
Cisco CRS-1 - Carrier Routing System Router Manual de usuario
Cisco
Cisco RPM-XF Manual de usuario
Cisco
Cisco 5915 Guía de inicio rápido
Cisco
Cisco ASR 9000 Series Manual de usuario
Cisco
Cisco AIRONET CB21AG Manual de usuario
Cisco
Cisco 805 Series Instrucciones de funcionamiento y seguridad
Cisco
Cisco AGS+ Manual de instrucciones
Cisco
Cisco 12406 series Manual de usuario
Cisco
Cisco ASR 5500 Manual de usuario
Cisco
Cisco Linksys WET11 Manual de usuario
Cisco
Cisco 2600-DC Series Manual de usuario
Cisco
Cisco 800 Series Cómo utilizar
Cisco
Cisco 10000 Series Manual de usuario
Cisco
Cisco 901 Manual de instalación
