Cisco 1100 Series Manual de instrucciones
Installing and Upgrading Internal Modules and
FRUs
•Installing and Upgrading Internal Modules and FRUs, page 1
Installing and Upgrading Internal Modules and FRUs
This document describes how to install and upgrade internal modules and field replaceable units (FRUs) in
the Cisco 1100 Series Integrated Services Routers (ISRs). The install and upgrade information is contained
in these sections:
Safety Warnings
Class 1 laser product. Statement 1008Warning
Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Statement 1030
Warning
Accessing Internal Modules
To access the internal modules on the router, you must first disconnect from the power source and then remove
the chassis cover. See the Replacing the Cover section for instructions on how to remove and later replace
the chassis cover on the routers.
Before opening the unit, disconnect the telephone-network cables to avoid contact with telephone-network
voltages. Statement 1041
Warning
Hardware Installation Guide for the Cisco 1100 Series Integrated Services Router
1
Replacing the Chassis Cover
The Cisco 1100 Series ISRs have a removable cover.
Do not run the router with the cover off. Doing so can cause the router to overheat very quickly.
Use a number-2 Phillips screwdriver to perform the following tasks.
Removing the Cover
To remove the cover, perform the following steps.
Step 1 Read the Safety Warnings and disconnect the power supply before you perform any module replacement.
Step 2 Confirm the router is turned off and disconnected from the power supply or power supplies. If a redundant power is
used, disconnect from the redundant power supply.
Step 3 Place the chassis on a flat surface.
Step 4 Remove all the screws on the both sides of the router; seven on each side.
Step 5 Pull the cover to disengage the slots along the front (bezel) edge of the chassis, as shown in the figure below.
Figure 1: Removing the Cover
Slots1
Hardware Installation Guide for the Cisco 1100 Series Integrated Services Router
2
Installing and Upgrading Internal Modules and FRUs
Accessing Internal Modules
Screw holes (7 numbers on each side)2
Replacing the Cover
To replace the cover, perform the following steps.
Step 1 Read the Safety Warnings, on page 1 and disconnect the power supply before you begin.
Step 2 Confirm the router is turned off and disconnected from the power supply or power supplies. If a redundant power is used
disconnect from the redundant power supply.
Step 3 Place the chassis on a flat surface.
Step 4 Locate the cover hooks on the mating slots and slide the cover towards the bezel side.
Step 5 Install seven screws on each side.
Locating Internal and External Slots for Modules
This section describes the locations of internal modules on the router motherboard. Internal modules include
PoE daughter card on the Cisco1100 Series ISRs.
Figure 2: Module Location in the Cisco 1100 Series ISR
Hardware Installation Guide for the Cisco 1100 Series Integrated Services Router
3
Installing and Upgrading Internal Modules and FRUs
Locating Internal and External Slots for Modules
PoE Module1
Installing the Internal PoE Daughter Card
Use the following procedure to install an Internal PoE daughter card:
Step 1 Read the Safety Warnings and disconnect the power supply before you perform any module installation.
Step 2 Confirm the router is turned off and disconnected from the power supply.
Step 3 Open the chassis according to the instructions in the Removing the Chassis section.
Step 4 Locate the three metal standoff holes, and install the metal standoffs into the three holes. Make sure that the standoffs
are straight when installed. Tighten them gently but firmly, to a torque of 6-8 in-lbf.
Step 5 Place the PoE daughter card on top of the three metal standoffs, lining up the screw holes in the PoE daughter card with
the metal standoffs.
Step 6 Gently push the PoE daughter card down towards the system board until it is firmly fixed.
Step 7 Insert the three M3 (48-0530-01) screws provided, through the PoE daughter card and into the metal standoffs. Tighten
the screws using a torque of 5 in-lb.
Step 8 Close the chassis cover according to the instructions in the Replacing the Cover section, and connect the power supply
cable.
Figure 3: Internal PoE Daughter Card Assembly
PoE Daughter Card2Screws1
Metal Standoffs3
Hardware Installation Guide for the Cisco 1100 Series Integrated Services Router
4
Installing and Upgrading Internal Modules and FRUs
Locating Internal and External Slots for Modules
Removing and Replacing the Internal PoE Daughter Card
Use the following procedure to remove and replace the Internal PoE daughter card:
Step 1 Read the Safety Warnings and disconnect the power supply before you remove or replace the module.
Step 2 Open the chassis, locate the PoE daughter card assembly.
Step 3 Remove the three M3 (48-0530-01) screws.
Step 4 Pull the PoE daughter card out of the connector. If replacing the card, insert the new PoE daughter card and tighten the
screws to a torque of 5 in-lb.
Step 5 Place the removed card in an anti-static bag to protect it from ESD damage.
To upgrade the PoE daughter card, follow the steps mentioned in the Installing the Internal PoE Daughter Card
section.
Note
Removing and Replacing the USB Flash Token Memory Stick
The Cisco 1100 Series ISRs contain port for a 1 GB flash token memory stick to store configurations or Cisco
IOS XE consolidated packages.
Only Cisco USB Flash memory modules are supported by Cisco routers.Note
Do not remove a USB Flash memory module when issuing some file access command or a read/write
operation to the Flash memory module when it is processing. The router might reload or the USB Flash
memory module can be damaged. You can check to see if the USB activity LED on the router front panel
is flashing, prior to the removal of the USB device
Caution
To remove and then replace a USB flash token memory stick from the router, follow these steps:
Step 1 Pull the memory stick from the USB port.
Step 2 To replace a Cisco USB Flash memory stick, simply insert the module into the USB port. The Flash memory module
can be inserted in only one way, and can be inserted or removed regardless of whether the router is powered up or not.
What to Do Next
This completes the USB Flash memory installation procedure.
Hardware Installation Guide for the Cisco 1100 Series Integrated Services Router
5
Installing and Upgrading Internal Modules and FRUs
Removing and Replacing the USB Flash Token Memory Stick
AC Power Supplies
Overview of the AC Power Supply
Power supply of the Cisco 1100 Series ISRs is an external AC to DC power adapter. The external power
adapter DC power connector plugs in to the router 4-pin power connector, to power the unit.
Figure 4: Power Supply Unit
Power Cable1
Installing and Removing SFP Modules
This section describes how to install optional small-form-factor pluggable (SFP) modules in the router to
provide optical Gigabit Ethernet connectivity.
The SFP module installs into a slot on the router rear panel. When selected in Cisco IOS software, it is assigned
port gigabitethernet 0/0/0. The default is the built-in RJ-45 1000Base-T connector, which is enabled on this
port.
Only SFP modules certified by Cisco are supported on the routers.
Table 1: SFPs Supported on the Router
DescriptionMinimum
IOS-XE Version
Cisco Model
Number
1000BASE-EX
SFP transceiver
module, SMF,
1310nm, DOM
3.15GLC-EX-SMD
Hardware Installation Guide for the Cisco 1100 Series Integrated Services Router
6
Installing and Upgrading Internal Modules and FRUs
AC Power Supplies
DescriptionMinimum
IOS-XE Version
Cisco Model
Number
GE SFP, LC
connector
LX/LH
transceiver
3.10GLC-LH-SM
9/1251000Base-ZXGLC-ZX-SM-X=
GE SFP, LC
connector
LX/LH
transceiver; with
DOM
3.10GLC-LH-SMD
GE SFP, LC
connector SX
transceiver
3.10GLC-SX-MM
GE SFP, LC
connector SX
transceiver; with
DOM
3.10GLC-SX-MMD
1000BASE-ZX
SFP
3.10GLC-ZX-SM
1000BASE-ZX
SFP; with DOM
3.16.1GLC-ZX-SMD
100BASE-FX
SFP for FE port
3.10GLC-FE-100FX
100BASE-LX
SFP for FE port
3.10GLC-FE-100LX
100BASE-ZX
SFP (80km)
3.10GLC-FE-100ZX
100BASE-EX
SFP (40km)
3.10GLC-FE-100EX
100BASE-BX10-D
SFP
3.11GLC-FE-100BX-D
100BASE-BX10-U
SFP
3.11GLC-FE-100BX-U
100 V02 SFP on
GE ports
3.10GLC-GE-100
V02
Hardware Installation Guide for the Cisco 1100 Series Integrated Services Router
7
Installing and Upgrading Internal Modules and FRUs
Installing and Removing SFP Modules
DescriptionMinimum
IOS-XE Version
Cisco Model
Number
1000BASE-BX80
SFP, 1570NM
3.16.1GLC-BX80-D-I
1000BASE-BX80
SFP, 1490NM
3.16.1GLC-BX80-U-I
1000BASE-BX40
SFP, 1550NM
3.16.1GLC-BX40-D-I
1000BASE-BX40
SFP, 1310NM
3.16.1GLC-BX40-U-I
1000BASE-BX
SFP, 1490NM
3.10GLC-BX-D
1000BASE-BX
SFP, 1310NM
3.10GLC-BX-U
1000BASE-SX
SFP transceiver
module for
MMF, 850-nm
wavelength,
extended
operating
temperature
range and DOM
support, dual
LC/PC
connector
3.13SFP-GE-S
CWDM 1470
NM SFP Gigabit
Ethernet and
1G/2G FC
3.10CWDM-SFP-1470
CWDM 1490
NM SFP Gigabit
Ethernet and
1G/2G FC
3.10CWDM-SFP-1490
CWDM 1510
NM SFP Gigabit
Ethernet and
1G/2G FC
3.10CWDM-SFP-1510
CWDM 1530
NM SFP Gigabit
Ethernet and
1G/2G FC
3.10CWDM-SFP-1530
Hardware Installation Guide for the Cisco 1100 Series Integrated Services Router
8
Installing and Upgrading Internal Modules and FRUs
Installing and Removing SFP Modules
DescriptionMinimum
IOS-XE Version
Cisco Model
Number
CWDM 1550
NM SFP Gigabit
Ethernet and
1G/2G FC
3.10CWDM-SFP-1550
CWDM 1570
NM SFP Gigabit
Ethernet and
1G/2G FC
3.10CWDM-SFP-1570
CWDM 1590
NM SFP Gigabit
Ethernet and
1G/2G FC
3.10CWDM-SFP-1590
CWDM 1610
NM SFP Gigabit
Ethernet and
1G/2G FC
3.10CWDM-SFP-1610
DWDM SFP
1530.33 nm SFP
(100 GHz ITU
grid)
3.10DWDM-SFP-3033
DWDM SFP
1531.12 nm SFP
(100 GHz ITU
grid)
3.10DWDM-SFP-3112
DWDM SFP
1531.90 nm SFP
(100 GHz ITU
grid)
3.10DWDM-SFP-3190
DWDM SFP
1532.68 nm SFP
(100 GHz ITU
grid)
3.10DWDM-SFP-3268
DWDM SFP
1534.25 nm SFP
(100 GHz ITU
grid)
3.10DWDM-SFP-3425
DWDM SFP
1535.04 nm SFP
(100 GHz ITU
grid)
3.10DWDM-SFP-3504
Hardware Installation Guide for the Cisco 1100 Series Integrated Services Router
9
Installing and Upgrading Internal Modules and FRUs
Installing and Removing SFP Modules
DescriptionMinimum
IOS-XE Version
Cisco Model
Number
DWDM SFP
1535.82 nm SFP
(100 GHz ITU
grid)
3.10DWDM-SFP-3582
DWDM SFP
1536.61 nm SFP
(100 GHz ITU
grid)
3.10DWDM-SFP-3661
DWDM SFP
1538.19 nm SFP
(100 GHz ITU
grid)
3.10DWDM-SFP-3819
DWDM SFP
1538.98 nm SFP
(100 GHz ITU
grid)
3.10DWDM-SFP-3898
DWDM SFP
1539.77 nm SFP
(100 GHz ITU
grid)
3.10DWDM-SFP-3977
DWDM SFP
1540.56 nm SFP
(100 GHz ITU
grid)
3.10DWDM-SFP-4056
DWDM SFP
1542.14 nm SFP
(100 GHz ITU
grid)
3.10DWDM-SFP-4214
DWDM SFP
1542.94 nm SFP
(100 GHz ITU
grid)
3.10DWDM-SFP-4294
DWDM SFP
1543.73 nm SFP
(100 GHz ITU
grid)
3.10DWDM-SFP-4373
DWDM SFP
1544.53 nm SFP
(100 GHz ITU
grid)
3.10DWDM-SFP-4453
Hardware Installation Guide for the Cisco 1100 Series Integrated Services Router
10
Installing and Upgrading Internal Modules and FRUs
Installing and Removing SFP Modules
Otros manuales para 1100 Series
3
Tabla de contenidos
Otros manuales de Enrutador de red de Cisco
Cisco
Cisco ASR 9000 Series Manual de usuario
Cisco
Cisco 7401ASR Manual del operador
Cisco
Cisco SOHO 71 Manual de usuario
Cisco
Cisco ASR 1001-X Manual de usuario
Cisco
Cisco 2524 - Router - EN Manual de usuario
Cisco
Cisco 7609 Manual de usuario
Cisco
Cisco Linksys SGE2010P Manual
Cisco
Cisco Linksys E4200 Manual del propietario
Cisco
Cisco ASR 903 Manual de usuario
Cisco
Cisco Linksys EtherFast BEFVP41 Manual de usuario
Cisco
Cisco 811 Manual de usuario
Cisco
Cisco 7200 VXR Series Instrucciones de funcionamiento y seguridad
Cisco
Cisco 2651 Manual de usuario
Cisco
Cisco RV042 - Small Business Dual WAN VPN Router Manual de usuario
Cisco
Cisco 676 Instrucciones de funcionamiento y mantenimiento
Cisco
Cisco ASR1002 - ASR 1002 Router Manual de usuario
Cisco
Cisco 1720 Manual de usuario
Cisco
Cisco 8100 Series Manual
Cisco
Cisco XR 1200 series Manual de instalación
Cisco
Cisco Profile Series Manual de usuario
