Cisco Catalyst 8200 Series Manual de usuario
Installing and Upgrading Field Replaceable Units
•Install and Remove Small Factor Pluggable, on page 1
•Removing and Replacing the Chassis Cover, on page 3
•Installing a DIMM, on page 4
•Removing a DIMM, on page 5
•Installing the M.2 Storage Module, on page 6
•Installing and Removing a NIM , on page 7
•Installing Pluggable Interface Module, on page 8
•Installing Drive Bays, on page 8
Install and Remove Small Factor Pluggable
Laser Safety Guidelines
Optical Small-Form Pluggable (SFPs) use a small laser to generate the fiber-optic signal. Keep the optical
transmit and receive ports covered whenever a cable is not connected to the port.
Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into beams or
view directly with optical instruments. Statement 1051
Warning
Ultimate disposal of this product should be handled according to all national laws and regulations. Statement
1040
Warning
Pluggable optical modules comply with IEC 60825-1 Ed. 3 and 21 CFR 1040.10 and 1040.11 with or without
exception for conformance with IEC 60825-1 Ed. 3 as described in Laser Notice No. 56, dated May 8, 2019.
Statement 1255.
Warning
To install an SFP module in your device, perform these steps:
Installing and Upgrading Field Replaceable Units
1
Step 1 Read the Safety Warnings section and disconnect the power supply before you perform any module replacement.
Step 2 Slide the SFP into the device connector until it locks into position
If the SFP uses a bale-clasp latch (see Laser Safety Guidelines section, the handle should be on top of the SFP
module.
Tip
Figure 1: Install a Small-Form Pluggable Module
Do not remove the optical port plugs from the SFP until you are ready to connect cabling.
Caution
Step 3 Connect the network cable to the SFP module.
Remove Small Form Pluggable Modules
Follow these steps to remove a Small Form Pluggable (SFP) from the device:
Step 1 Read the Safety Warnings section and disconnect the power supply before you perform any module replacement.
Step 2 Disconnect all cables from the SFP.
Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into beams or
view directly with optical instruments. Statement 1051
Warning
The latching mechanism used on many SFPs locks the SFP into place when cables are connected. Do not pull
on the cabling in an attempt to remove the SFP.
Caution
Step 3 Disconnect the SFP latch.
SFP modules use various latch designs to secure the module in the SFP port. Latch designs are not linked to
SFP model or technology type. For information on the SFP technology type and model, see the label on the
side of the SFP.
Note
Installing and Upgrading Field Replaceable Units
2
Installing and Upgrading Field Replaceable Units
Remove Small Form Pluggable Modules
Figure 2: Disconnecting SFP Latch Mechanisms
Bale-clasp latch3Sliding latch1
Plastic collar latch4Swing and slide latch2
Use a pen, screwdriver, or other small straight tool to gently release a bale-clasp handle if you cannot reach it
with your fingers.
Tip
Step 4 Grasp the SFP on both sides and remove it from the device.
Removing and Replacing the Chassis Cover
Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement
1030
Warning
These are the steps to remove the chassis cover:
1. Confirm that the chassis is turned off and disconnected from the power supply or power supplies.
2. Place the chassis on a flat surface.
3. Remove the screws at top of the chassis cover.
4. Remove one screw from each side of the device as shown in the following figure.
Installing and Upgrading Field Replaceable Units
3
Installing and Upgrading Field Replaceable Units
Removing and Replacing the Chassis Cover
Figure 3: Removing the Chassis Cover
5. Lift the chassis cover after you have removed all the screws.
To replace the chassis cover, place the cover evenly on the top of the device and use the screws to secure it
to the device.
Note
Installing a DIMM
There are two DDR4 DIMM slots. DIMMs have a polarization notch on the connecting edge to prevent
incorrect insertion.
Figure 4: DIMM Showing Polarization Notch
Polarization Notch1
Installing and Upgrading Field Replaceable Units
4
Installing and Upgrading Field Replaceable Units
Installing a DIMM
These are the steps to install a DIMM:
1. Remove the chassis cover.
2. Locate the DIMM slot on thedevice. There are two DIMM slots in the chassis and you can install the
DIMM module on either of the slots.
3. Make sure that both latches on the DIMM connector are in the open position.
4. Orient the DIMM so that the polarization notch lines up with the polarization key on the connector.
5. Insert the DIMM into the connector.
6. Replace the chassis cover.
Removing a DIMM
These are the steps to remove a DIMM:
1. Remove the chassis cover.
2. Locate the DIMM module on the device. Refer to the Chassis-Internal section to identify and locate the
DIMM module.
3. Pull the latches away from the DIMM at both ends to lift the DIMM slightly. Pull the DIMM out of the
socket.
Installing and Upgrading Field Replaceable Units
5
Installing and Upgrading Field Replaceable Units
Removing a DIMM
Figure 5: Removing a DIMM
4. Place the DIMM in an antistatic bag to protect it from ESD damage.
5. Replace the chassis cover.
Installing the M.2 Storage Module
The M.2 storage modules come with different storage capacities and can be replaced through the front panel
if required.
These are the steps to upgrade the M.2 storage module:
1. Power off of the system before replacing M.2.
2. Locate the M.2 storage module slot. Refer to Chassis - Front Panel to identify and locate the module.
Figure 6: Blank M.2 Slot
M.2 slot blank cover1
3. Loosen the screws that secures the M.2 blank cover or existing M.2 module in the slot.
Installing and Upgrading Field Replaceable Units
6
Installing and Upgrading Field Replaceable Units
Installing the M.2 Storage Module
4. Plug in the new M.2 storage module in the same location and secure it with the screws.
M.2 module orientation with metal
carrier on top, M.2 module underneath.
2Securing screws (torque 3.9-5.4 in-lbs)1
Chassis cutout prevents M.2 installation
in wrong orientation.
3
Installing and Removing a NIM
These are the steps to install a NIM:
1. Locate the NIM slot on the front panel.
2. Loosen the screws to remove NIM blank cover.
3. Insert the NIM into the slot.
4. Tighten the screws to secure the NIM in the slot.
These are the steps to remove a NIM:
1. If the NIM is up and running, issue the following command to shut down the NIM gracefully before
removing it:
hw-module subslot slot 0/2 stop
If you do not shut down the NIM gracefully before removing it, the NIM card could get damaged.
Caution
2. Locate the NIM slot on the front panel.
3. Loosen the screws that secure the NIM.
4. Gently pull out the NIM from the slot.
Installing and Upgrading Field Replaceable Units
7
Installing and Upgrading Field Replaceable Units
Installing and Removing a NIM
All module slots must have a module or blank installed for the product to work thermally and for safety
purposes.
Installing Pluggable Interface Module
To insert the PIM into the router, do these steps:
1. Insert and then gently push the PIM into the pluggable slot until firmly fixed.
2. Tighten the screw.
PIM Module2Securing screw1
Installing Drive Bays
If you have not ordered drives, the drive bay slot is closed with a blank cover.
These are the steps to install a drive in a drive bay:
1. The drive bay is in the front panel of the device. The bay is closed with a cover if there are no drives in
the slots.
2. Press the push button on the center of the cover and pull the cover out of the system to expose the slot.
3. Slide the drive into the slot.
Keep the drive bays covered when there are no drives installed in the slot.
Note
Installing and Upgrading Field Replaceable Units
8
Installing and Upgrading Field Replaceable Units
Installing Pluggable Interface Module
Tabla de contenidos
Otros manuales de Puerta de Cisco
Cisco
Cisco AudioCodes MP-1288 Manual de usuario
Cisco
Cisco IG21 Series Manual
Cisco
Cisco Meraki Z3 Manual de usuario
Cisco
Cisco ASR 5000 Series Manual de instrucciones
Cisco
Cisco IP/VC 3526 Cómo utilizar
Cisco
Cisco Expressway CE500 Manual de usuario
Cisco
Cisco 3545 PRI Manual de instalación y operación
Cisco
Cisco Meraki Z3C Manual de usuario
Cisco
Cisco Linksys AG310 Manual de usuario
Cisco
Cisco Catalyst CG113-W6 Manual
Cisco
Cisco DPC2434 Manual de usuario
Cisco
Cisco ISDN GW 3241 Manual de usuario
Cisco
Cisco DPC2434 Manual de usuario
Cisco
Cisco ATA 186 Manual del operador
Cisco
Cisco IG21 Series Manual de usuario
Cisco
Cisco DPC3848V Manual de usuario
Cisco
Cisco ASR 5000 Series Manual de instrucciones
Cisco
Cisco ASR 5000 Series Manual de instrucciones
Cisco
Cisco Linksys SPA8000-XU Instrucciones de funcionamiento originales
Cisco
Cisco 545 Serial Manual de instalación y operación
Manuales populares de Puerta de otras marcas
LST
LST M500RFE-AS Manual de usuario
Kinnex
Kinnex Media Gateway Manual de usuario
2N Telekomunikace
2N Telekomunikace 2N StarGate Manual de usuario
Mitsubishi Heavy Industries
Mitsubishi Heavy Industries Superlink SC-WBGW256 Manual de usuario
ZyXEL Communications
ZyXEL Communications ZYWALL2 ET 2WE Manual de usuario
Telsey
Telsey CPVA 500 - SIP Manual de usuario
