Cisco TelePresence System Codec C60 Manual de instrucciones

Installing Cisco TelePresence System Codec C60

This box contains:

Codec C60

Top tray

TRC V remote control

A. Rack profiles (2 pcs)

B. Rack rear brackets (2 pcs)

C. Rack extension brackets (2 pcs)

D. Rack ear profiles (2 pcs)

Accessories box and cable kit

• HDMI cable (3m / 10ft)

• Ethernet cable (5 m / 16ft)

• Power cable (1.8 m / 6 ft)

• Batteries LR03 AAA 1.5V for the remote control

• Screwdriver, combi 2mm / 4 mm Allen Key (unbraco)

• Screws (M6 and M3) and cage nuts (M6)

• Universal rack brackets*

* Universal rack brackets: Use these only if the supplied rail based rack

mounting kit does not fit your type of rack.

User guides

The user documentation for this product, including compliance

and safety information, is available on the Cisco web site.

Go to: http://www.cisco.com/go/cseries-docs

Rack mounting

WARRANTY: Rack mounting the codec without using the

supplied mounting kit will void the warranty.

b) Snap the cage

nuts to the rack.

1Assembling the rack profiles

Slide the rack profiles A and B together. 3Mounting the rack profiles to the rack

Mount the left and right rack profiles A+B(+C) to the rack. The screws,

screwdriver and cage nuts are found in the accessories box.

2Optional: Assembling the extension rails

If the rack is deeper than the length of the

rack profiles A+B, then the extension rails C are

needed.

A+B

LEFT

RIGHT

d) On both sides:

Fasten the rack profiles A+B

together, using one M3 screw on

each side.

Tool: Screwdriver, 2 mm Allen Key

a) Mount the rack profiles in front

using two M6 screws on each side.

Tool: Screwdriver, 4 mm Allen Key

c) Mount the rack

profiles on the rear

side using the M6

knob screws.

Mount the extension rail (C) to the

rack profiles (A+B) using M6 screws.

Tool: Screwdriver, 4 mm Allen Key Details in front Details on rear side

AB BA

D D

Remote Control

A+B

Please follow the steps in

this installation guide when

rack mounting the codec.

NOTE: The profile should

be assembled with the

bend in the direction as

shown in the illustration.

NOTE: If the supplied rack profiles are incompatible

with the rack, use the supplied universal rack

brackets.

Follow the instructions in step 4 on the next page

when assembling the universal rack brackets.

Rack mounting and connecting cables

TIP

If the menu is not already present,

press Home key or OK key on the

remote control to open the menu.

Navigate in the menu with the

arrow keys.

ghi

pqrs

abc/123

jkl

tuv

abc

def

mno

wxyz

EMC Class A declaration

WARNING: This is a class A product. In a domestic environment this

product may cause radio interference in which case the user may be

required to take adequate measures.

声

明

此为A级产品，在生活环境中，该产品可能会造成无线电干扰。在这种

情况下，可能需要用户对其干扰采取切实可行的措施。

WARNING: This is a class A product. In a domestic environment

this product may cause radio interference in which case the user

may be required to take adequate measures.

Installing Cisco TelePresence System Codec C60

4Assembling the rack ear profiles

Mount the rack ear profiles to the codec. 5Mounting the codec onto the rack

Locate the rails and carefully slide the codec onto the rack.

b) Fasten the codec in front

by tightening the screws on

the rack ear profiles.

Video from the camera

(HDMI to HDMI)

LAN/Ethernet Mains power

cable

Loudspeakers

(optional)

Camera control cable

(RJ45 to DSUB)

6Connecting cables

The C60 codec offers a great flexibility in connecting

audio and video equipment to the system.

a) Remove the two M3 screws on

the left and right side of the codec.

Tool: Screwdriver, 2 mm Allen Key

b) Use the same two M3 screws to

fasten the rack ear profiles to the

codec.

a) Locate the rails on the codec and the

rails on the rack. Lift the codec towards

the rack and make sure the codec enter

the rails. Carefully slide the codec into the

rack.

Power switch

After having

connected the

cables, you may

turn the codec On.

For a basic setup, you should go through these steps:

1. Connect the main camera to the HDMI 1 input using a

HDMI to HDMI cable

• For camera control you should also connect the

camera to the Camera Control input using the

dedicated cable that came with your camera (RJ45

to DSUB)

2. Connect the monitor display to the HDMI 1 output using

a HDMI to HDMI cable

3. If you want to send images from a PC, connect the PC

to the DVI-I 3 input, using a DVI to DVI or a HDMI to DVI

cable (for digital signals) or VGA to DVI cable (for analog

signals) depending on your PC’s capabilities

• Audio from the PC could be connected to Line 1

and 2 inputs for stereo signals

4. Connect the microphone to the XLR input

5. The loudspeakers should be connected to Line 1 and 2

outputs

6. Connect the codec to the IP network using the

Ethernet 1 interface

7. Connect the power and use the power switch to turn

the codec on

NOTE: If using the DVI-I out 2 for the main monitor a shortcut

is required to move the on screen display (OSD) to this

output. On the remote control key in the following sequence:

• Disconnect – *– #– *– #– 0– 2– #

PC (audio to Line In 1)

Monitor (audio from

HDMI 1 or Line Out 1-2)

Microphone

INPUTS OUTPUTS Basic setup

The main connectors for basic

setup are highlighted in orange.

1 1

IMPORTANT

There should always be a distance of

minimum 10 cm / 4in. free space in front

of the codec.

SAFETY REQUIREMENT

Make sure the codec is not mounted with

the front side up or down.

Min. 10 cm

Basic setup - The main connectors are highlighted in orange color.

Otros manuales para TelePresence System Codec C60

Otros manuales de Sistema de conferencias de Cisco

Cisco

Cisco EX60 Manual de servicio

Cisco

Cisco SX80 Manual de usuario

Cisco

Cisco TelePresence MX300G2 Manual de usuario

Cisco

Cisco Telepresence MX200 Manual de servicio

Cisco

Cisco SX80 Manual de servicio

Cisco

Cisco TelePresence IP VCR 2200 Series Manual de usuario

Cisco

Cisco MX200 G2 Manual de servicio

Cisco

Cisco TelePresence DX70 Manual de usuario

Cisco

Cisco TelePresence System Codec C40 Manual de servicio

Cisco

Cisco TelePresence Manual de usuario

Cisco

Cisco TelePresence Touch 10 Manual de usuario

Cisco

Cisco 3515 MCU12 Manual de instalación y operación

Cisco

Cisco Profile Series Instrucciones de montaje

Cisco

Cisco SX80 Manual de usuario

Cisco

Cisco TelePresence System TX9000 Guía de configuración rápida

Cisco

Cisco TelePresence DX80 Manual de usuario

Cisco

Cisco Telepresence MX800 Guía

Cisco

Cisco Room Kit EQ Manual de usuario

Cisco

Cisco TelePresence System Codec C60 Manual de servicio

Cisco

Cisco 7936 - IP Conference Station VoIP Phone Manual de usuario

Cisco

Cisco Webex Room Kit Mini Manual de usuario

Cisco

Cisco Webex Room Kit Manual de usuario

Cisco

Cisco TelePresence System C20 Plus Manual de usuario

Cisco

Cisco TelePresence System Codec C90 Manual de instrucciones

Manuales populares de Sistema de conferencias de otras marcas

Kramer

Kramer VIA GO Manual de usuario

AVT

AVT MAGIC AC1 Go Manual de usuario

ProSoft Technology

ProSoft Technology AN-X4-AB-DHRIO Manual de usuario

Sony

Sony PCS-I150 Manual de usuario

Middle Atlantic Products

Middle Atlantic Products VTC Series Manual de usuario

Prentke Romich Company

Prentke Romich Company Vanguard Plus Guía

Speakerbus

Speakerbus iD 712 Manual de usuario

Trelleborg

Trelleborg SafePilot CAT PRO Manual de usuario

Sennheiser

Sennheiser ADN Manual de usuario

ADTRAN

ADTRAN NetVanta 7100 Manual de usuario

AINA

AINA PTT Voice Responder Manual de usuario

Yamaha

Yamaha ProjectPhone PJP-100H Manual de usuario

vissonic

vissonic VLI Series Manual de usuario

Panasonic

Panasonic KX-VC500 Manual de usuario

Poly

Poly Trio 8300 Manual de usuario

Crestron

Crestron Mercury CCS-UCA-SMK Dibujo dimensional

Inmarsat

Inmarsat mini M Manual de usuario

Tenveo

Tenveo ALL-IN-ONE Manual de usuario