Cisco NCS 4016 Manual de instrucciones
Unpacking the Chassis
This chapter describes how to unpack the Cisco NCS 4016 chassis.
Use the complete Cisco Systems packaging for shipment of product or components. Failure to properly use
Cisco packaging may result in damage or loss of the product.
Caution
•Unpacking the Chassis, on page 1
Unpacking the Chassis
The chassis is shipped on a pallet by itself and is enclosed in a corrugated box, held in place by plastic bands.
Prerequisites
Before performing this task, be sure to have sufficient room around the chassis pallet for unpacking.
Required Tools and Equipment
• Cutters to cut strapping (plastic bands)
Steps
To unpack the Cisco NCS 4016 chassis, follow these steps:
SUMMARY STEPS
1. Carefully move the pallet containing the Cisco NCS 4016 chassis to the staging area where you plan on
unpacking it.
2. Cut the plastic bands holding the chassis shipping box in place.
3. Remove the six plastic clips on the outer sleeve using a flat head screw driver.
4. Remove the accessories, corrugated accessory tray and the top foam cap.
5. Leave the chassis on the pallet until you are ready to move and install the chassis in a rack.
DETAILED STEPS
Step 1 Carefully move the pallet containing the Cisco NCS 4016 chassis to the staging area where you plan on unpacking it.
Unpacking the Chassis
1
The Cisco NCS 4016 chassis with pallet should be handled carefully to eliminate the risk of tipping over the
package.
Caution
Step 2 Cut the plastic bands holding the chassis shipping box in place.
Figure 1: Chassis Shipping Box
Step 3 Remove the six plastic clips on the outer sleeve using a flat head screw driver.
Unpacking the Chassis
2
Unpacking the Chassis
Unpacking the Chassis
Figure 2: Chassis in Original Packaging
Unpacking the Chassis
3
Unpacking the Chassis
Unpacking the Chassis
Step 4 Remove the accessories, corrugated accessory tray and the top foam cap.
Step 5 Leave the chassis on the pallet until you are ready to move and install the chassis in a rack.
Be sure to save the packaging in case you need to return any of the components.
Tip
What to do next
What to Do Next
After performing this task, go to the Removing the Chassis from the Pallet, on page 4.
Removing the Chassis from the Pallet
This procedure describes how to remove the support brackets that secure the chassis to the pallet.
Figure 3: Hardware Locations for Support Brackets
8 bolts with washers (4 on each side)228 M4 screws (14 on each side)1
Required Tools and Equipment
• Number 1 and number 2 Phillips screwdrivers
• 3/8-in. socket wrench or 3/8-in. drive ratchet wrench
Steps
To remove the chassis from the pallet and then transfer the chassis to a moving device, follow these steps:
Unpacking the Chassis
4
Unpacking the Chassis
Removing the Chassis from the Pallet
SUMMARY STEPS
1. Using the Phillips #2 screwdriver, remove the fourteen M4 screws that connect the right support bracket
to the chassis.
2. Using the 3/8-in. socket wrench, remove the 4 hex cap bolts that connect the right support bracket to the
pallet.
3. Set the support bracket aside carefully.
4. Repeat Step 1 through Step 3 for the left support bracket.
DETAILED STEPS
Step 1 Using the Phillips #2 screwdriver, remove the fourteen M4 screws that connect the right support bracket to the chassis.
Unpacking the Chassis
5
Unpacking the Chassis
Removing the Chassis from the Pallet
Figure 4: Removing the Chassis Support Brackets
Step 2 Using the 3/8-in. socket wrench, remove the 4 hex cap bolts that connect the right support bracket to the pallet.
Unpacking the Chassis
6
Unpacking the Chassis
Removing the Chassis from the Pallet
Step 3 Set the support bracket aside carefully.
Step 4 Repeat Step 1 through Step 3 for the left support bracket.
What to do next
What to Do Next
After you have removed the support brackets that secure the chassis to the pallet, go to the Transferring the
Chassis to a Mechanical Lifting Device.
Unpacking the Chassis
7
Unpacking the Chassis
Removing the Chassis from the Pallet
Unpacking the Chassis
8
Unpacking the Chassis
Removing the Chassis from the Pallet
Otros manuales para NCS 4016
2
Tabla de contenidos
Otros manuales de Chasis de Cisco
Cisco
Cisco CRS-1 - Carrier Routing System Router Manual de usuario
Cisco
Cisco ASA 5508-X Manual de usuario
Cisco
Cisco Nexus 7018 Manual de usuario
Cisco
Cisco NCS 4000 Series Manual
Cisco
Cisco SCE8000 GBE Manual de instrucciones
Cisco
Cisco ONS 15454 DWDM Instrucciones de funcionamiento
Cisco
Cisco 7513 Series Guía
Cisco
Cisco NCS 1010 Manual de usuario
Cisco
Cisco NCS 4000 Series Manual
Cisco
Cisco cBR Manual de usuario
Cisco
Cisco NCS 1004 Manual
Cisco
Cisco SRS Series Manual de usuario
Cisco
Cisco ONS 15454 Manual de usuario
Cisco
Cisco UCS M4308 Guía
Cisco
Cisco Firepower 4100/9300 Manual de usuario
Cisco
Cisco Nexus 3000 series Manual de instrucciones
Cisco
Cisco AS5350 - Universal Access Server Manual de usuario
Cisco
Cisco NCS 1001 Manual de usuario
Cisco
Cisco NCS 6000 Manual de usuario
Cisco
Cisco Nexus 7010 Manual de instrucciones
