Cisco ONS 15454 Manual de usuario

Turning Up a Node

This chapter explains how to provision a single Cisco ONS 15454 node and turn it up for service, including

assigning the node name, date, and time; provisioning timing references; provisioning network attributes such

as IP address and default router; setting up users and user security; installing cards; and creating DWDM

connections.

The procedures and tasks described in this chapter for the Cisco ONS 15454 platform is applicable to the

Cisco ONS 15454 M2 and Cisco ONS 15454 M6 platforms, unless noted otherwise.

Note

Procedures in this chapter require that you have a network plan calculated for your DWDM network with

Cisco Transport Planner. Cisco Transport Planner is a DWDM planning tool that is available from your Cisco

account representative. Cisco Transport Planner prepares a shelf plan for each network node and calculates

the power and attenuation levels for the DWDM cards installed in the node. For information about Cisco

Transport Planner, contact your Cisco account representative. For instructions on using Cisco Transport

Planner, refer to the Cisco Transport Planner DWDM Operations Guide.

Note

Unless otherwise specified, in this document “ONS 15454” refers to both ANSI (ONS 15454) and ETSI

(ONS 15454 SDH) shelf assemblies.

Note

Cisco Transport Controller (CTC) views referenced in these procedures depend on the mode. In single-shelf

mode, the views are network, node, and card. In multishelf mode, the views are network, multishelf, shelf,

and card. For more information about CTC views, refer to CTC Enhancements, Operations, and Shortcuts.

Note

In this chapter, “100G-LC-C card” refers to the 15454-M-100G-LC-C card. “10x10G-LC” refers to the

15454-M-10x10G-LC card. “CFP-LC” refers to the 15454-M-CFP-LC card.

Note

•NTP-G341 Setting Up Secure Access to TL1, on page 2

Turning Up a Node

•OpenSSH Version, on page 3

•NTP-G29 Setting Up SNMP, on page 3

•NTP-G328 Adding, Modifying, or Deleting ANS Parameters, on page 13

•NTP-G30 Installing the DWDM Cards, on page 18

•NTP-G179 Installing the Transponder and Muxponder Cards, on page 22

•NTP-G123 Installing the Filler Cards, on page 26

•NTP-G34 Installing Fiber-Optic Cables on DWDM Cards and DCUs, on page 27

•NTP-G140 Installing Fiber-Optic Cables Between Terminal, Hub, or ROADM Nodes, on page 31

•NTP-G185 Installing Fiber-Optic Cables between Mesh Nodes, on page 49

•NTP-G191 Installing Fiber-Optic Cables on Passthrough ROADM Nodes, on page 53

•NTP-G141 Installing Fiber-Optic Cables for Y-Cable Protection Modules, on page 55

•NTP-G39 Verifying OSCM Transmit Power, on page 60

•NTP-G210 Provisioning Node for SNMPv3, on page 63

•NTP-G211 Provisioning Node to Send SNMPv3 Traps, on page 63

•NTP-G212 Manually Provisioning a GNE/ENE to Manage an ENE using SNMPv3, on page 64

•NTP-G213 Automatically Provisioning a GNE to Manage an ENE using SNMPv3, on page 65

•NTP-G214 Manually Provisioning a GNE/ENE to Send SNMPv3 Traps using SNMPv3, on page 66

•NTP-G215 Automatically Provisioning a GNE/ENE to Send SNMPv3 Traps Using SNMPv3, on page

•NTP-G355 Provisioning OTDR , on page 79

NTP-G341 Setting Up Secure Access to TL1

This procedure provisions the nodes for secure access

to TL1.

Purpose

NoneTools/Equipment

NTP-G26 Set Up CTC Network AccessPrerequisite Procedures

As neededRequired/As Needed

Onsite or remoteOnsite/Remote

SuperuserSecurity Level

Procedure

Step 1 In the node view, click the Provisioning >Security >Access pane.

Step 2 Under the TL1 Access area, change the Access State to Secure.

Step 3 Click Apply.

Existing non-secure TL1 sessions, if any, are terminated.

Step 4 To create a secure TL1 connection, enter the following command at the UNIX or Linux prompt:

ssh -l username node-ip -p port-number

Turning Up a Node

NTP-G341 Setting Up Secure Access to TL1

The port number for secure TL1 is 4083. The port number for non-secure TL1 is3083.

EPNM-based interfaces need to be updated with the correct port details for the node.

Use any SSH client on Windows.

Note

Stop. You have completed this procedure.

OpenSSH Version

The OpenSSH version that is currently supported is 3.5.9.1 and will be upgraded in a future release.

The OpenSSH has been upgraded to Cisco SSH Release 1.4.

Note

NTP-G29 Setting Up SNMP

This procedure provisions the SNMP parameters so

that you can use SNMP management software with

the ONS 15454.

Purpose

NoneTools/Equipment

•DLP-G46 Log into CTC

•NTP-G22 Verifying Common Card Installation

Prerequisite Procedures

Required if SNMP is used at your site.Required/As Needed

Onsite or remoteOnsite/Remote

Provisioning or higherSecurity Level

Procedure

Step 1 In node view (single-shelf mode) or multishelf view (multishelf mode), click the Provisioning >SNMP tabs.

Step 2 In the Trap Destinations area, click Create.

Step 3 Complete the following in the Create SNMP Trap Destination dialog box.

• Destination IP Address—Type the IP address of your network management system (NMS). If the node

you are logged into is an ENE, set the destination address to the GNE.

You can configure IPv6 addresses for SNMPv2/v3 trap destinations and SNMPv3 proxy targets,

in addition to IPv4 addresses.

Note

Turning Up a Node

OpenSSH Version

• Community—Type the SNMP community name. For a description of SNMP community names, refer

to the SNMP document.

The community name is a form of authentication and access control. The community name

assigned to the ONS 15454 is case-sensitive and must match the community name of the NMS.

Note

• UDP Port—The default User Datagram Protocol (UDP) port for SNMP is 162.

• Trap version—Choose either SNMPv1 or SNMPv2. Refer to your NMS documentation to determine

which version to use.

• Click OK. The node IP address of the node where you provisioned the new trap destination appears in

the Trap Destinations area.

Step 4 Click the node IP address in the Trap Destinations area. Verify the SNMP information that appears in the

Selected Destination list.

Step 5 If you want the SNMP agent to accept SNMP SET requests on certain MIBs, click the Allow SNMP Sets

check box. If this box is not checked, SET requests are rejected.

Step 6 If you want to set up the SNMP proxy feature to allow network management, message reporting, and

performance statistic retrieval across firewalls, click the Allow SNMP Proxy check box located on the SNMP

tab.

The Use Generic MIB check box is normally not checked for MSTP. It is checked only when the

ONS 15454 resides in networks with multiple ONS products, and the network management system

requires MIBs with the same name to have the same object IDs. By default, the ONS 15454 uses

the CERENT-454-MIBs. Other ONS products, such as the ONS 15600, the ONS 15327, and ONS

15310-CL, use the CERENT-GENERIC-MIBs. If Use Generic MIB is checked, the ONS 15454

will use the CERENT-GENERIC-MIBs so the object IDs will be the same for all products.

Note

Using the firewall proxy feature effectively breaches the firewall to exchange management

information.

For more information about the SNMP proxy feature, refer to SNMP.

Note

Step 7 Click Apply.

Step 8 If you are setting up SNMP proxies, you can set up to three relays that send SNMP trap error counts back to

the NE for each trap destination address:

a) Click the first trap destination IP address. The address and its community name appear in the Destination

fields.

b) Enter up to three SNMP Proxy relay addresses and community names in the fields for Relay A, Relay B,

and Relay C.

The community names specified for each relay node must match one of the provisioned SNMP

community names in the NE.

Note

The SNMP proxy directs SNMP traps from this node through Relay A to Relay B to Relay C

to the trap destination. Ensure that you enter the IP addresses in the correct order so that this

sequence runs correctly.

Note

Step 9 Click Apply.

Turning Up a Node

NTP-G29 Setting Up SNMP

Stop. You have completed this procedure.

DLP-G351 Deleting a Card in CTC

This task deletes a card from an ONS 15454 slot that

is provisioned in CTC.

Purpose

NoneTools/Equipment

DLP-G46 Log into CTCPrerequisite Procedures

As neededRequired/As Needed

Onsite or remoteOnsite/Remote

Superuser onlySecurity Level

It is recommended that the card be physically removed from its slot after deleting it from CTC.

Note

Procedure

Step 1 Verify that the following conditions are not present. (During node turn-up, these conditions are normally not

present):

• The card is a control card.

• The card is part of a protection group.

• The card has optical channels or overhead circuits provisioned.

• The card is being used for timing.

• The card has an OSC/GCC termination.

• A port on the card is being used for a Link Management Protocol (LMP) channel or link.

• The card is part of an optical side.

• The card is assigned to DWDM patchcords.

• If a port on the card is in service.

• If a port on the card is part of a circuit.

If any of these conditions exist, do not continue. You will not be able to delete the card until the card is

removed from protection groups; circuits, DCC, and GCCs are deleted; a different timing source is provisioned,

and the LMP link or channel is deleted.

• To delete a protection group, see the NTP-G83 Modify or Delete Card Protection Settings procedure.

Turning Up a Node

DLP-G351 Deleting a Card in CTC

• To delete optical channels see the DLP-G347 Deleting Optical Channel Client Connections and the

DLP-G106 Deleting Optical Channel Network Connections; to delete overhead circuits, see the DLP-G112

Deleting Overhead Circuits.

• To remove the card as a timing source, see the NTP-G87 Change Node Timing Parameters procedure.

• To remove OSC or GCC terminations, see the NTP-G85 Modify or Delete OSC Terminations, GCC

Terminations, and Provisionable Patchcords procedure.

• To delete LMP channels or links, see NTP-G164 Configure Link Management Protocol.

• To remove a DWDM patchcord, see the DLP-G355 Deleting an Internal Patchcord .

• To remove an optical side, see the DLP-G480 Deleting an Optical Side .

Step 2 On the shelf graphic in CTC, right-click the card that you want to remove and choose Delete Card.

Step 3 Return to your originating procedure (NTP).

DLP-G353 Pre-provisioning a Slot

This task pre-provisions a ONS 15454 slot in CTC.

Pre-provisioning of all the slots in the shelf is

normally performed when you complete the

NTP-G143 Importing the Cisco Transport Planner

NE Update Configuration File procedure. Use this

task if you need to manually pre-provision a slot. All

slot pre-provisioning must be based on the

Cisco Transport Planner shelf layout prepared for your

site.

Purpose

Cisco Transport Planner shelf layout table or JPG file.Tools/Equipment

•NTP-G139 Verifying Cisco Transport Planner

Reports and Files

•DLP-G46 Log into CTC

Prerequisite Procedures

As neededRequired/As Needed

Onsite or remoteOnsite/Remote

Provisioning or higherSecurity Level

Procedure

Step 1 In node view (single-shelf mode) or multishelf view (multishelf mode), right-click an empty slot where you

want to install a card.

Step 2 From the Add Card shortcut menu, choose the card type that will be installed based on the

Cisco Transport Planner shelf layout. Only cards that can be installed in the slot appear in the Add Card

Turning Up a Node

DLP-G353 Pre-provisioning a Slot

shortcut menu. The following table shows the Add Card shortcut menu, submenu, card groups, and menu

options or cards that they reference.

Turning Up a Node

DLP-G353 Pre-provisioning a Slot

Table 1: CTC Add Card Shortcut Menu for DWDM Cards

CardsSubmenu Item 2Submenu Item 1Card GroupSubmenu

Manuales populares de Chasis de otras marcas

Advantech

Advantech IPC-623 Series Manual de usuario

IMC Networks

IMC Networks iMcV/18 Manual de usuario

Chenbro

Chenbro RB13804N4WFT Manual de usuario

Lenovo

Lenovo ThinkSystem SR665 V3 Manual de usuario

Wuntronic

Wuntronic PCI4DRQ Manual de usuario

EtherWAN

EtherWAN EMC400 Manual de usuario

Overland Storage

Overland Storage SnapSAN S1000 Guía

Philips

Philips LC4.1E A Manual de usuario

Supermicro

Supermicro SCF418 Series Manual de usuario

Chenbro

Chenbro RM437 Series Manual de usuario

Pickering

Pickering 40-914 Manual de usuario

HP A7503-S Instrucciones de montaje

Supermicro

Supermicro SC823MTQ-R700LPB Manual de usuario

SilverStone

SilverStone RMS08 Series Manual de usuario

NI cRIO-FRC II Manual de usuario

Pickering

Pickering 65-200 Manual de usuario

Allied Telesis

Allied Telesis AT-MMCR18 Manual de usuario

Hisense

Hisense MSD6586 Manual de usuario