Cisco ATA 186 Manual de usuario

Configuration Guide

for the

Cisco ATA 186

CafeFone Configuration Guide for the Cisco ATA186

TABLE OF CONTENTS

INTRODUCTION _____________________________________________ 1

Requirements ______________________________________________________ 1

Support ___________________________________________________________ 1

SET UP YOUR ATA ____________________________________________ 1

CONFIGURE AN IP ADDRESS _________________________________ 1

Configure the ATA to Use DHCP _____________________________________ 2

Configure the ATA to Use Static IP Addressing _________________________ 2

CONFIGURE THE ATA’S ACCOUNT AND NETWORK SETTINGS __ 4

PLACE CALLS TO A TELEPHONE OUTSIDE THE NETWORK _____ 6

Page i

CafeFone Configuration Guide for the Cisco ATA186

INTRODUCTION

This Configuration Guide will outline the steps for configuring the CISCO® ATA 186 Analog Telephone

Adaptor (ATA) for calling using the CafeFone service.

For more details on installing or configuring the ATA, please review the User’s Guide, located at:

http://www.cisco.com/univercd/cc/td/doc/product/voice/ata/index.htm

For release notes on the SIP 3.1.0 firmware, please review the Release Notes, located at:

http://www.cisco.com/univercd/cc/td/doc/product/voice/ata/atarn/atarn3_1.htm

REQUIREMENTS

yConnection to a broadband Internet Service Provider (ISP) or Local Area Network (LAN).

yAn account number and passcode for each CafeFone phone port.

(If you do not have an account number or passcode, please contact your local reseller.)

yAny conventional analog telephone.

yA Cisco ATA with firmware version 3.1.0 or higher.

yA PC connected to the same network as the ATA. (For initial configuration steps only.)

SUPPORT

If you need technical support for using the ATA with the CafeFone service, please contact your local reseller.

SET UP YOUR ATA

To set up your ATA:

1. Connect the ATA to your Ethernet port by plugging one end of an Ethernet cable (RJ-45) into the

back of the ATA and the other end into a broadband router or LAN port.

2. Connect your telephone into the ATA by plugging a standard RJ-11 telephone cable from your

phone into the ATA’s Phone1 port.

To connect another telephone, plug a standard RJ-11 telephone cable from the second phone into the

ATA’s Phone2 port.

3. Power on the ATA by plugging its power supply into an AC outlet and then plugging the power

cable into the power supply port on the back of the ATA. The ATA will power on, and the button on

top of the ATA will begin to blink.

CONFIGURE AN IP ADDRESS

In order to properly set up your CafeFone account and network settings, your ATA must be assigned an IP

address.

Your ATA’s IP address can be dynamic (DHCP) or static. To configure your ATA for DHCP, continue to the

next section, DHCP Configuration. To configure your ATA with a static IP address, skip to the Static IP

Configuration section on page 2.

Page 1

CafeFone Configuration Guide for the Cisco ATA186

CONFIGURE THE ATA TO USE DHCP

To configure your ATA to use DHCP:

1. Pick up the handset of the phone connected to the ATA, and then press the button on top of the

ATA. The system announces, “Configuration Menu. Enter menu number followed by the # key…”

2. Press 20# on the phone’s keypad to access the DHCP menu. The system announces, “Enter value.”

3. Press 1# to enable DHCP. The system announces, ”You entered ‘1.’ To change, press 1; to review,

press 2; to save, press 3; to review your saved value, press 4; or press the pound key (#) to exit.”

4. Press 3on the phone’s keypad to save the settings. The system announces, ”Value saved.

Configuration Menu…”

5. Place the phone’s handset back on the phone to hang up. The light on top of the device will flash red

for a second.

Note: If the ATA continues to flash the red light for more than two minutes, it is not connected to a DHCP server.

Configure the ATA with a static IP address instead. Refer to the Static IP Configuration section on page 2.

6. To confirm the IP address assigned to the ATA, pick up the handset of the phone connected to the

ATA, and then press the button on top of the ATA. The system announces, “Configuration Menu.

Enter menu number followed by the # key…”

7. Press 80# on the phone’s keypad to hear the IP address. When the system announces the ATA’s IP

address, write it down.

Note: To repeat the IP address announcement, press 80# again.

Note: If the system announces the IP address as “0.0.0.0,”there could be two possible causes. The first possibility is

that the network to which the ATA is connected does not have a DHCP server. If this is the case, skip to the

Static IP Configuration section on page 2. The second possibility is that the DHCP server has been unable to

assign an IP address to the ATA. If that is the case, notify your network administrator of the problem.

8. Place the phone’s handset back on the phone to hang up. To continue configuring the ATA for

CafeFone, skip to the Configuring Account and Network Settings section on page 4.

CONFIGURE THE ATA TO USE STATIC IP ADDRESSING

To configure the ATA with a static IP address:

1. Contact your Internet Service Provider (ISP) or IT Administrator, and obtain the following

information:

IP address

Default Gateway address

Subnet Mask address

Primary DNS Server address

Secondary DNS Server address (optional)

Page 2

CafeFone Configuration Guide for the Cisco ATA186

2. Pick up the handset of the phone connected to the ATA, then press the button on top of the ATA.

The system announces, “Configuration Menu. Enter menu number followed by the # key…”

3. Press 20# on the phone’s keypad to access the DHCP menu. The system announces, “Enter value.”

4. Press 0# on the phone’s keypad to disable DHCP. The system announces, ”You entered ‘0.’ To

change, press 1; to review, press 2; to save, press 3; to review your saved value, press 4; or press the

pound key (#) to exit.”

5. Press 3on the phone’s keypad to save the settings. The system announces, ”Value saved.

Configuration Menu…”

6. Press 1# on the phone’s keypad to access the IP address menu. The system announces, “Enter

value.”

7. Using the phone’s keypad, enter the IP address. To enter the dots (.), use the star key (*) key (e.g., to

enter the IP address 000.00.000.00, you would press 000*00*000*00). When you are done entering the

address, press the pound (#) key.

For example, press 000.00.000.00# to enter the IP address “000.00.000.00.”

The system announces, ”You entered ‘xxx.xxx.xx.xxx’ (where xxx.xxx.xx.xxx is your IP address). To

change, press 1; to review, press 2; to save, press 3; to review your saved value, press 4; or press the

pound key (#) to exit.”

8. Press 3on the phone’s keypad to save the settings. The system announces, ”Value saved.

Configuration Menu…”

9. Press 2# on the phone’s keypad to access the Default Gateway menu. The system announces, “Enter

value.”

10. Using the phone’s keypad, enter the default gateway address To enter the dots (.), use the star key

(*) key. When you are done entering the address, press the pound (#) key. The system announces,

”You entered ‘xxx.xxx.xx.xxx’ (where xxx.xxx.xx.xxx is your default gateway). To change, press 1; to

review, press 2; to save, press 3; to review your saved value, press 4; or press the pound key (#) to

exit.”

11. Press 3on the phone’s keypad to save the settings. The system announces, ”Value saved.

Configuration Menu…”

12. Press 10# on the phone’s keypad to access the Subnet Mask menu. The system announces, “Enter

value.”

13. Using the phone’s keypad, enter the subnet mask address. To enter the dots (.), use the star key (*)

key. When you are done entering the address, press the pound (#) key. The system announces,

”You entered ‘xxx.xxx.xx.xxx’ (where xxx.xxx.xx.xxx is your subnet mask). To change, press 1; to

review, press 2; to save, press 3; to review your saved value, press 4; or press the pound key (#) to

exit.”

14. Press 3on the phone’s keypad to save the settings. The system announces, ”Value saved.

Configuration Menu…”

15. Press 916# on the phone’s keypad to access the primary DNS server menu. The system announces,

“Enter value.”

16. Using the phone’s keypad, enter the primary DNS server address. To enter the dots (.), use the star

key (*) key. When you are done entering the address, press the pound (#) key. The system

Page 3

CafeFone Configuration Guide for the Cisco ATA186

announces, ”You entered ‘xxx.xxx.xx.xxx’ (where xxx.xxx.xx.xxx is your primary DNS server

address). To change, press 1; to review, press 2; to save, press 3; to review your saved value, press 4;

or press the pound key (#) to exit.”

17. Press 3on the phone’s keypad to save the settings. The system announces, ”Value saved.

Configuration Menu…”

18. If there is a secondary DNS server on your network, press 917# on the phone’s keypad to access the

secondary DNS server menu. The system announces, “Enter value.”

19. To enter and save the secondary DNS server address, follow the instructions in steps 16 and 17.

20. Press 3on the phone’s keypad to save the settings. The system announces, ”Value saved.

Configuration Menu…”

21. Place the phone’s handset back on the phone to hang up.

CONFIGURE THE ATA’S ACCOUNT AND NETWORK

SETTINGS

In order to be able to place calls, the ATA must be configured with the appropriate CafeFone account and

network settings.

To enter the configuration parameters via the Web Configuration page:

1. Pick up the handset of the phone connected to the ATA, and then press the button on top of the

ATA. The system announces, “Configuration Menu. Enter menu number followed by the # key…”

2. Press 80# on the phone’s keypad to hear the IP address. When the system announces the ATA’s IP

address, write it down.

3. Launch a Web browser, and in the Address bar, enter http:// + the ATA’s IP address + /dev.

For example, if the ATA’s IP address were 000.00.000.00, you would enter http://000.00.000.00/dev in

the browser’s Address bar.

4. Enter the information as it appears in the Cisco ATA 186 Web Configuration table below. When you

are finished, click the Apply button to save the settings. The ATA will reboot.

5. Click the Click here to reload link to display the updated settings on the Web page.

The ATA is now ready to place and receive calls.

Page 4

CafeFone Configuration Guide for the Cisco ATA186

The shaded values denote required fields.

CISCO ATA 186 WEB CONFIGURATION

UIPassword ToConfig 0

UseTftp 0 TftpURL 0

CfgInterval 3600 EncryptKey 0

Dhcp 1 StaticIP 10.1.1.108

StaticRoute 10.1.1.1 StaticNetMask 255.255.255.0

UID0 NOPHONE PWD0 Passcode for CafeFone account

number for line 1.

UID1 NOPHONE1 PWD1 Passcode for CafeFone account

number for line 2. If only using line 1,

leave blank (0).

GkOrProxy sip.cafefone.com Gateway 0

GateWay2 0.0.0.0 UseLoginID 1

LoginID0 CafeFone account number. LoginID1 CafeFone account number.

If only using Port 1, leave blank (0).

AltGk 0 AltGkTimeOut 0

GkTimeToLive 300 GkId .

UseSIP 1 SIPRegInterval 300

MaxRedirect 5 SIPRegOn 1

NATIP 0.0.0.0 SIPPort 5060

MediaPort 10000 OutBoundProxy 0

NatServer 0 NatTimer 0x00000000

LBRCodec 0 AudioMode 0x00150015

RxCodec 0 TxCodec 0

NumTxFrames 1 CallFeatures 0xffffffff

PaidFeatures 0x00000000 CallerIdMethod 0x00019e60

CallWaitCallerId 0x003c33d0 Polarity 0x00000000

ConnectMode 0x00060400 AutMethod 0x00000002

TimeZone 17 NTPIP 0.0.0.0

AltNTPIP 0.0.0.0 DNS1IP 0.0.0.0

DNS2IP 0.0.0.0 UDPTOS 0x000000a0

SigTimer: 0x01418564 OpFlags 0x00000002

Nprintf 0.0.0.0.0 TraceFlags 0x00000000

RingOnOffTime 2,4,25 IPDialPlan 1

DialPlan #.r9t1|**St4-|#St4-|911|1>#t8.r9t2-

|0>#t811.rat4-|^1t4>#.-

DialTone 2,31538,30831,3100,3885,1,0,0,1000

BusyTone 2,30467,28959,1191,1513,0,4000,4000,

ReorderTone 2,30467,28959,1191,1513,0,2000,2000

RingBackTone 2,30831,30467,1943,2111,0,16000,320

00,0

CallWaitTone 1,30831,0,5493,0,0,2400,2400,4800

AlertTone 1,30467,0,5970,0,0,480,480,1920 CallCmd Af;AH;BS;NA;CS;NA;Df;EB;Ff;EP;

Kf;EFh;HQ;Jf;AFh;HQ;I*67;gA*82;f

A#90v#;OI;H#72v#;bA#74v#;cA#7

5v#;dA#73;eA*67;gA*82;fA*70;iA*6

9;DA*99;xA;Uh;GQ;

Page 5

CafeFone Configuration Guide for the Cisco ATA186

PLACE CALLS TO A TELEPHONE OUTSIDE THE NETWORK

To place a call to a telephone outside the CafeFone network:

1. Pick up the handset of the phone connected to the ATA, and confirm that there is a dial tone.

2. Dial the phone number you would like to call. Press the pound key (#) to send the call immediately.

Otherwise, the call will be sent in four seconds.

TYPE OF CALL DIAL PATTERN

Domestic calls (within the US) 1 + area code + 7-digit telephone number

International calls (placed from the US) 011 + country code + city code + telephone number

Calling from outside the US to the US 1 + area code + 7-digit telephone number

Calling from outside the US 011 + country code + city code + telephone number

3. When the call is complete, place the phone’s handset back on the phone to hang up.

4. If you would like to make another call, pick up the handset of the phone connected to the ATA, and

repeat steps 1 through 3.

Page 6

Otros manuales para ATA 186

Tabla de contenidos

Otros manuales de Adaptador de Cisco

Cisco

Cisco ATA186-I1 Manual de servicio

Cisco

Cisco AIRONET CB21AG Manual del operador

Cisco

Cisco SPA122 Manual de usuario

Cisco

Cisco LINKSYS PLTS200 Manual de usuario

Cisco

Cisco SPA232D Manual de usuario

Cisco

Cisco PA-A2 Manual del operador

Cisco

Cisco PAP2T Manual de usuario

Cisco

Cisco SPA2102-AN - Single Port Router Manual de instrucciones

Cisco

Cisco Linksys PCM1000 Instrucciones de funcionamiento originales

Cisco

Cisco Linksys SPA 2102 Manual de usuario

Cisco

Cisco ATA 191 Manual de instrucciones

Cisco

Cisco SPA112 Manual de instrucciones

Cisco

Cisco PA-2FEISL-TX Instrucciones de funcionamiento y mantenimiento

Cisco

Cisco SPA112 Manual de usuario

Cisco

Cisco PA-2FE-TX Instrucciones de funcionamiento y mantenimiento

Cisco

Cisco Linksys WGA11B Manual de usuario

Cisco

Cisco LINKSYS USB1000 Manual de usuario

Cisco

Cisco MicroCell Manual de usuario

Cisco

Cisco Linksys PLS300 Manual de usuario

Cisco

Cisco AIR-PCI340 Manual del operador

Cisco

Cisco Linksys WMA11B Manual de usuario

Cisco

Cisco Cisco Aironet Wireless LAN Client Manual del operador

Cisco

Cisco PA-2CE1 Series Instrucciones de funcionamiento y mantenimiento

Cisco

Cisco PA-4B-U Instrucciones de funcionamiento y mantenimiento

Manuales populares de Adaptador de otras marcas

PCB Piezotronics

PCB Piezotronics 090B274 Manual de usuario

Auvidea

Auvidea J20 Manual del producto

Gossen MetraWatt

Gossen MetraWatt AT3-III E Manual de usuario

Akribis

Akribis ITF-21-BISS-MIT Manual de usuario

Tenda

Tenda W54U Manual de usuario

ROHO

ROHO AGILITY Manual de usuario

PROLiNK

PROLiNK WN2001 Manual de usuario

Hawking

Hawking HUF2 Manual de usuario

Airlink101

Airlink101 AWLC4030 Manual de usuario

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Manual de usuario

Philips

Philips SWA4554S/10 Manual de usuario

JVC

JVC TS-C9D2B Manual de instrucciones

NETGEAR

NETGEAR A6100 Manual de usuario

D-Link

D-Link DWA-121 Manual de usuario

Philips

Philips SWA2037 Manual de usuario

Basalte

Basalte 0610-20 Manual de usuario

Yealink

Yealink EHS40 Manual de usuario

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Manual de usuario