Chore-Time ATF 42343 Manual de usuario

Model ATF End Control with Sensor Plus

1. Attach one Swinging Pan Support (item 4) and three regular Pan Supports (item 2) to Pan Shield (item 3) using

rivets supplied. Always attach the Swinging Pan Support (item 4) at the same location on all Pan Shields (item

3). It will be necessary to support the Pan Shield (item 3) while installing the rivets. Use a hammer to drive

rivets as shown in Figure 1.

Figure 1. Assembling the Pan Supports to the Pan Shield

2. Install the Sensor Switch Assembly (item 1) to the Drop Tube (item 3) using the included #8 Hex Washer Head

Screw (item 2).

Figure 2. Installing the Sensor Switch Assembly to the Drop Tube

3. Install the Drop Tube Assembly (item 2) to the Pan Shield Assembly (item 1) by routing the Drop Tube

Assembly (item 2) up through the center of Pan Shield Assembly (item 1). Make sure the cord from the Sensor

Switch Assembly passes through the hole in the side of the Pan Shield Assembly (item 1).

Figure 3. Assembling the Drop Tube to the Pan Shield Assembly

Model ATF™ End Control with Sensor Plus™

Part Number 42343

and

Model ATF End Control Update Kit

Part Number 43711

1630-11 11/99

Item Description

1 Wood Block

2 Pan Support

3 Pan Shield

4 Swinging Pan Support

1630-2 11/99

Item Description

1 Sensor Switch Assembly

2 #8 Hex Washer Head Screw

3 Drop Tube

1630-3 11/99

Item Description

1 Pan Shield Assembly

2 Drop Tube Assembly

MF1630BDecember 2000

Model ATF™End Control with Sensor Plus™

MF1630B

4. Assemble the ATF End Control Body (item 1) to the Drop Tube with Pan Shield (item 2) by sliding the

ATF End Control Body (item 1) into the top of the Drop Tube with Pan Shield (item 2).

Figure 4. Assembling the ATF End Control to the Drop Tube Assembly

5. Secure the ATF End Control Body (item 2) to the Drop Tube Assembly using the included 1/4-20 Hex

Head Bolts (item 1).

Figure 5. Securing the ATF End Control Body

6. Route the Sensor Switch Assembly Cord up through the black Water Tight Connector on the bottom of

the Relay Box (item 1). Tighten the Water Tight Connector around the Sensor Switch Assembly Cord

making sure there is enough cord inside the Relay Box (item 1) to plug into the Socket on the Circuit

Board. Mount the Relay Box to the side of the ATF End Control Body (item 3) and secure using the

included #10-32 Hex Lock Nuts (item 2).

Figure 6. Installing the Relay Box to the ATF End Control Body

1630-4 11/99

Item Description

1 ATF End Control Body

2 Drop Tube with Pan Shield

1630-5 11/99

Item Description

1 1/4-20 Hex Head Bolts

2 ATF End Control Body

1630-6 11/99

Item Description

1 Relay Box

2 #10-32 Hex Lock Nuts

3 ATF End Control Body

Model ATF™End Control with Sensor Plus™

MF1630B

7. Install the Anchor Plate (item 2) to the Drive Unit (item 1) using the included 1/4-20 Hex Head Bolts

(item 3).

Figure 7. Installing the Anchor Plate to the Drive Unit

8. Connect the Plug (item 8) from the Sensor Switch Assembly into the Socket (item 7) on the Circuit

Board (item 9). See Figure 8.

Install the Pan Shield Assembly onto the Feeder Pan (item 6) by hooking the Swing Down Pan Support

through the hole in the Feeder Pan (item 6). Install the Feed Level Tube (item 4) and the Feed Level

Ring (item 5) then swing the pan upand snap the remaining Pan Supports over the lipof the Feeder Pan

(item 6). See Figure 8.

Important Do not bend the Pan Supports during assembly.

Install the Drive Unit and Anchor Plate (item 1) to the ATF End Control Body (item 3) using the

included 1/4-20 Hex Head Bolts (item 2). See Figure 8.

Figure 8. Assembling the components

1630-7 11/99

123Item Description

1DriveUnit

2 Anchor Plate

3 1/4-20 Hex Head Bolts

1630-8 8/2000

4 5

Item Description

1 Drive Unit and Anchor Plate

2 1/4-20 Hex Head Bolt

3 ATF End Control Body

4 Feed Level Tube

5 Feed Level Ring

6 Feeder Pan

7Socket

8Plug

9 Circuit Board with Heater

Model ATF™End Control with Sensor Plus™

MF1630B

9. Install the 90° Metal Conduit Connector (item 1) to the Motor (item 3). Cut the Flex Conduit (item 2)

to length and assemble with the 90° Metal Conduit Connector (item 1). Route the three wires through

the Flex Conduit (item 2) into the Motor (item 3) and assemble the Flex Conduit (item 2) with the

Conduit Connector (item 4) at the Relay Box (item 5). Wire the Motor (item 3) in accordance with the

motor plate.

Figure 9. Wiring the ATF End Control

10. Install the Metal Water Tight Connector (item 1) in the Feed Line Motor (item 2). Cut the Flex Conduit

(item 3) to length. Slide the wires from the end control through the Flex Conduit (item 3). Install the

Flex Conduit (item 3) in the connectors. Connect the wires to the Feed Line Motor (item 2).

Figure 4. Wiring the Motor

Item Description Part No. Item Description Part No.

1Metal Water Tight Connector 23810 7Product Identification Decal 2529-734

2Feed Line Motor ——— 8 Body Cover 27942

3Flexible Conduit 26982-1 9Bottom Plate 27893

4Water Tight Connector 26980 10 White Wire ———

5Safety Cover Assembly 27941 11 Black Wire ———

6Cord Assembly 4999-100 12 Green Wire ———

1630-9 11/99

Item Description

1 90° Metal Conduit Connector

2 Flex Conduit

3Motor

4 Conduit Connector

5RelayBox

  

  

  

 

DANGER

   

      

   

   

      

   





 !

Do not open this control box

until electrical power is

disconnected at circuit

breakers.

1630-14 8/2000

12346

Model ATF™End Control with Sensor Plus™

MF1630B

Model ATF End Control Update Kit

The Model ATF End Control Update Kit is designed to replace an existing mechanical switch with a Sensor

Plus switch.

1. Disconnect the power at the circuit breaker. Remove and discard the Power Cord (item 6), 90°Romex

Connector (item 1) on the Motor, Motor Wires (item 3), Flex Conduit (item 2), Switch Box (item 4),

and Switch Box Mounting Plate (item 5).

Figure ?. Removing parts that will be replaced

2. Swing the Feeder Pan (item 5) down out of the way and remove the Drop Tube Assembly (item 3),

Feed Level Tube (item 1), and Feed Level Ring (item 2). Remove and discard the Switch Assembly

(item 4).

Figure ?. Removing the Switch Assembly

3. Reassemble following the instructions for the Model ATF End Control with Sensor Plus.

HAZARD

ELECTROCUTION

Donot open thiscon-

trolb oxu ntilelectrical

poweris disconnected

at circuitbreakers.

2527- 25

MF1630-12 8/2000

Item Description

190°Romex Connector

2 Flex Conduit

3 Motor Wires

4SwitchBox

5 Switch Box Mounting Plate

6PowerCord

MF1630-13 8/2000

Item Description

1 Feed Level Tube

2 Feed Level Ring

3 Drop Tube Assembly

4 Switch Assembly

5 Feeder Pan

Model ATF™End Control with Sensor Plus™

MF1630B

Switch Adjustment

The SENSOR PLUS Pan Half Round Sensor Switch is adjusted at the factory to a sensitivity of .25'' [6 mm]

and a time delay of 15 seconds, but they may be changed for a specific installation. The sensitivity

adjustment range is 0'' to .80'' [0 mm to 15 mm] and the time delay adjustment is 0 seconds to 600 seconds.

To adjust the Sensitivity:

•For less sensitivity —turn Sensitivity Adjusting Screw (item 4) clockwise

•For more sensitivity —turn Sensitivity Adjusting Screw (item 4) counter-clockwise

To adjust the Time Delay:

•For less time —turn Time Delay Adjusting Screw (item 5) clockwise (Light blinks fast)

•For more time —turn Time Delay Adjusting Screw (item 5) counter-clockwise (Light blinks slow)

Figure 2. Adjusting the SENSOR PLUS Proximity Switch

Internal Wiring

Control Wiring Diagram

1629-11 5/2000





 

0-15 mm

1-600 SEC

0$; 0,1



Item Description Part No.

1 Proximity Switch Cord ———

2 Switch Box 42627-3

3 Circuit Board with Heater 42604

4 Sensitivity Adjusting Screw ———

5 Time Delay Adjusting Screw ———

6Light ———

—Proximity Sensor Switch and

Circuit Board 44915

—Rectangle Sensor with Heater 42593

NCNO

COM

GREEN

BLACK

WHITE

BLACK

WHITE

BLACK

WHITE

MPLUG FROM

SENSOR SWITCH

1630-16 8/2000

bb 9751

WHITE

230 V

60 HZ, 1 PH

SUPPLY 1

Item Description Part No.

1 Rectangle Sensor

with Heater 42593

End

Control

Ground

3 Wire Hook Up (Typical)

Ground

1634-07 5/2000

2529-710

   

      

   

 

  

 

  

    

  



 



  

   

    !"

   

'$1*(5

 

     

        

     

 

  

 



 





   



  

   

    ! "

    

'$1*(5

Intermediate

Control

Shown with

3259-84

Power Unit

Bypass Switch

(not supplied)

230 VAC

Supply

60 HZ

Green

Black

White

Red

Black

White

White Black

Red

Model ATF™End Control with Sensor Plus™

MF1630B

Parts Listing

Model ATF End Control with Sensor Plus

*These items may be ordered as a Level Sensor Assembly, Part Number 44920.

Item Description Part No. Item Description Part No.

1Feed Level Tube 4341 17 Danger/Product Identification Decal 2529-734

2Control Body 27889 18 Electrical Box 42627-4

3Safety Cover Assembly 27941 19 1/2'' Conduit Connector 26980

4Anti Roost Guard 2798 20 Mounting Cover 6956

5Body Cover 27942 21 Switch Box Gasket 6777

6Stub Tube Weldment 27900 22 Switch Box Cover 6776

790°Metal Conduit Connector 23810 23 Swing Down Pan Support 24274

81/2'' Flexible Conduit 26982-1 24 Drive Rivet 4200

91/2'' Water Tight Connector 24685 25 Tube Support 24891

10 Cord Assembly 4999-100 26 Bottom Plate 27893

11* Proximity Switch Circuit Board 42604 27 Pan Shield 4191

12 1/2'' Conduit Lock Nut 43662 28 Pan Support 4199

13 1/2'' Water Tight Connector 23779 29 Guard Assembly 4892

14 Plastic Adapter Plate 43819 30 ATF Plastic Feeder Pan 29000

15 Adapter Plate 43813 31 Drop Tube Weldment 4180

16* Proximity Switch Sensor 42593 32 Feed Level Ring 29320

   

#$% & ' "

(&)##*+,*- -...



'$1*(5

   

      

   

  

    

  



    

   !

Do notopen thiscontrol box

until electrical power is

disconnected at circuit

breakers.

1630-15 8/2000

Model ATF™End Control with Sensor Plus™

MF1630B

Model ATF End Control Update Kit Part Number 43711

*These items may be ordered as a Level Sensor Assembly, Part Number 44920.

Item Description Part No. Item Description Part No.

190°Metal Conduit Connector 23810 9Electrical Box 42627-4

21/2'' Flexible Conduit 26982-1 10 1/2'' Water Tight Connector 23779

31/2'' Water Tight Connector 24685 11 Adapter Plate 43813

4Cord Assembly 4999-100 12* Rectangle Sensor with Heater 42593

5Box Cover 6776 13 Cover Decal 2529-734

6Gasket 6777 14 Plastic Adapter Plate 43819

7Mounting Cover 6956 15 1/2'' Conduit Lock Nut 43662

81/2'' Conduit Connector 26980 16* Circuit Board with Heater 42604

1630-10 11/99

123

10 15

Chore-Time Equipment a Division of CTB Inc.

P.O. Box 2000 •Milford, Indiana 46542-2000 •U.S.A.

Phone (219) 658-4101 •Fax (877) 730-8825

E-Mail: ctb@ctbinc.com •Internet: http//www.ctbinc.com

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Unidad de control de Chore-Time

Chore-Time

Chore-Time PDS Control 4 Guía de configuración

Chore-Time

Chore-Time Tronics 3 Manual de usuario

Chore-Time

Chore-Time Chore-Tronics Model 8 Manual de instrucciones

Chore-Time

Chore-Time 108 FLEX-AUGER Manual de usuario

Chore-Time

Chore-Time Chore-Tronics 2 Manual de usuario

Chore-Time

Chore-Time Chore-Tronics Natural Ventilation Manual de instrucciones

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario