Chicago Electric 62133 Instrucciones de montaje

Visit our website at: http://www.harborfreight.com

Email our technical support at: [email protected]

ITEM 62133

800 WATT HEAT BOND

CARPET

SEAMING IRON

REV 14f

Owner’s Manual & Safety Instructions

Save This Manual Keep this manual for the safety warnings and precautions, assembly,

operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the

back of the manual near the assembly diagram (or month and year of purchase if product has no number).

Keep this manual and the receipt in a safe and dry place for future reference.

When unpacking, make sure that the product is intact

and undamaged. If any parts are missing or broken,

please call 1-888-866-5797 as soon as possible.

No portion of this manual or any artwork contained herein may be reproduced in

any shape or form without the express written consent of Harbor Freight Tools.

Diagrams within this manual may not be drawn proportionally. Due to continuing

improvements, actual product may differ slightly from the product described herein.

Tools required for assembly and service may not be included.

Read this material before using this product.

Failure to do so can result in serious injury.

SAVE THIS MANUAL.

Item 62133 For technical questions, please call 1-888-866-5797. Page 2

SAVE THIS MANUAL

Keep this manual for the safety

warnings and precautions, assembly,

operating, inspection, maintenance and

cleaning procedures. Write the product’s

serial number in the back of the manual

near the assembly diagram (or month

and year of purchase if product has no

number). Keep this manual and the

receipt in a safe and dry place for future

reference.

IMPORTANT SAFETY

INFORMATION

In this manual, on the labeling,

and all other information

provided with this product:

This is the safety alert

symbol. It is used to alert

you to potential personal

injury hazards. Obey all

safety messages that

follow this symbol to avoid

possible injury or death.

DANGER indicates

a hazardous

situation which, if not

avoided, will result in death or

serious injury.

WARNING

indicates a

hazardous situation which, if

not avoided, could result in

death or serious injury.

CAUTION, used

with the safety

alert symbol, indicates a

hazardous situation which, if

not avoided, could result in

minor or moderate injury.

NOTICE is used to

address practices

not related to personal injury.

CAUTION, without

the safety alert

symbol, is used to address

practices not related to

personal injury.

General Tool Safety Warnings

WARNING Read all safety

warnings and instructions.

Failure to follow the warnings and

instructions may result in electric

shock, fire and/or serious injury.

Save all warnings and

instructions for future reference.

1. Work area safety

a.Keep work area clean and well

lit. Cluttered or dark areas invite

accidents.

b.Do not operate tools in explosive

atmospheres, such as in the

presence of flammable liquids,

gases or dust. Tools create sparks

which may ignite the dust or fumes.

c. Keep children and bystanders

away while operating a tool.

Distractions can cause you to lose

control.

2. Electrical safety

a.Tool plugs must match the outlet.

Never modify the plug in any way.

Do not use any adapter plugs with

Item 62133 For technical questions, please call 1-888-866-5797. Page 3

grounded tools. Unmodified plugs

and matching outlets will reduce risk

of electric shock.

b.Avoid body contact with grounded

surfaces such as pipes, radiators,

ranges and refrigerators. There is

an increased risk of electric shock if

your body is grounded.

c. Do not expose tools to rain or wet

conditions. Water entering a tool

will increase the risk of electric shock.

d.Do not abuse the cord. Never use

the cord for carrying, pulling or

unplugging the tool. Keep cord

away from heat, oil, sharp edges

or moving parts. Damaged or

entangled cords increase the risk of

electric shock.

e.If operating a tool in a damp

location is unavoidable, use a

Ground Fault Circuit Interrupter

(GFCI) protected supply. Use of

a GFCI reduces the risk of electric

shock.

3. Personal safety

a.Stay alert, watch what you are

doing and use common sense

when operating a tool. Do not use

a tool while you are tired or under

the influence of drugs, alcohol or

medication. A moment of inattention

while operating tools may result in

serious personal injury.

b.Use personal protective

equipment. Always wear eye

protection. Safety equipment such

as fresh air mask, non-skid safety

shoes, hard hat, or hearing protection

used for appropriate conditions will

reduce personal injuries.

c. Do not overreach. Keep proper

footing and balance at all times.

This enables better control of the tool

in unexpected situations.

d.Only use safety equipment

that has been approved by an

appropriate standards agency.

Unapproved safety equipment may

not provide adequate protection. Eye

protection must be ANSI-approved

and breathing protection must be

NIOSH-approved for the specific

hazards in the work area.

4. Tool use and care

a.Do not force the tool. Use the

correct tool for your application.

The correct tool will do the job better

and safer at the rate for which it was

designed.

b.Disconnect the plug from the

power source and allow to cool

before making any adjustments,

changing accessories, or storing

this tool. Such preventive safety

measures reduce the risk of damage

or injury.

c. Store idle tools out of the reach of

children and do not allow persons

unfamiliar with this tool or these

instructions to operate the tool.

Tools are dangerous in the hands of

untrained users.

d.Maintain tools. Check for

misalignment or breakage of

parts and any other condition that

may affect the tool’s operation. If

damaged, have the tool repaired

before use. Many accidents are

caused by poorly maintained tools.

5. Service

a.Have your tool serviced by a

qualified repair person using only

identical replacement parts. This

Item 62133 For technical questions, please call 1-888-866-5797. Page 4

will ensure that the safety of the tool

is maintained.

Safety Warnings

1. Maintain labels and nameplates on

the tool. These carry important safety

information. If unreadable or missing,

contact Harbor Freight Tools for a

replacement.

2. Place securely on Iron Holder (6)

when not in use.

3. Keep away from flammable objects.

4. Do not overheat adhesive.

5. When using a handheld tool, maintain

a firm, controlling grip on the tool.

6. Do not leave the tool unattended

when it is plugged into an electrical

outlet. Unplug the tool from its

electrical outlet and allow to cool

down before leaving.

7. This product is not a toy. Keep it out

of reach of children.

8. Any power cord must be properly

grounded. Ground Fault Circuit

Interrupter (GFCI) should also be

implemented – it prevents sustained

electrical shock.

9. WARNING: The cord of this product

contains lead, a chemical known

to the State of California to cause

cancer, and birth defects or other

reproductive harm. Wash hands

after handling. (California Health &

Safety Code § 25249.5, et seq.)

10. The warnings, precautions,

and instructions discussed in

this instruction manual cannot

cover all possible conditions and

situations that may occur. It must

be understood by the operator that

common sense and caution are

factors which cannot be built into this

product, but must be supplied by the

operator.

SAVE THESE

INSTRUCTIONS.

GROUNDING

TO PREVENT

ELECTRIC SHOCK

AND DEATH FROM

INCORRECT GROUNDING

WIRE CONNECTION:

Check with a qualified

electrician if you are in doubt

as to whether the outlet is

properly grounded. Do not

modify the power cord plug

provided with the tool. Never

remove the grounding prong

from the plug. Do not use the

tool if the power cord or plug

is damaged. If damaged, have

it repaired by a qualified

service technician before use.

If the plug will not fit the

outlet, have a proper outlet

installed by a qualified

electrician.

Item 62133 For technical questions, please call 1-888-866-5797. Page 5

Grounded Tools: Tools with Three

Prong Plugs

1. Tools marked with “Grounding

Required” have a three wire cord

and three prong grounding plug.

The plug must be connected to a

properly grounded outlet. If the tool

should electrically malfunction or

break down, grounding provides a

low resistance path to carry electricity

away from the user, reducing the risk

of electric shock. (See 3-Prong Plug

and Outlet.)

2. The grounding prong in the plug is

connected through the green wire

inside the cord to the grounding

system in the tool. The green wire

in the cord must be the only wire

connected to the tool’s grounding

system and must never be attached

to an electrically “live” terminal. (See

3-Prong Plug and Outlet.)

3. The tool must be plugged into an

appropriate outlet, properly installed

and grounded in accordance with all

codes and ordinances. The plug and

outlet should look like those in the

preceding illustration. (See 3-Prong

Plug and Outlet.)

Extension Cords

1. Grounded tools require a three wire

extension cord. Double Insulated

tools can use either a two or three

wire extension cord.

2. As the distance from the supply

outlet increases, you must use a

heavier gauge extension cord. Using

extension cords with inadequately

sized wire causes a serious drop in

voltage, resulting in loss of power and

possible tool damage.

(See Table A.)

3. The smaller the gauge number of the

wire, the greater the capacity of the

cord. For example, a 14 gauge cord

can carry a higher current than a 16

gauge cord. (See Table A.)

4. When using more than one extension

cord to make up the total length,

make sure each cord contains at

least the minimum wire size required.

(See Table A.)

5. If you are using one extension cord

for more than one tool, add the

nameplate amperes and use the sum

to determine the required minimum

cord size. (See Table A.)

6. If you are using an extension cord

outdoors, make sure it is marked with

the suffix “W-A” (“W” in Canada) to

indicate it is acceptable for outdoor

use.

7. Make sure the extension cord is

properly wired and in good electrical

condition. Always replace a damaged

extension cord or have it repaired by

a qualified electrician before using it.

8. Protect the extension cords from

sharp objects, excessive heat, and

Item 62133 For technical questions, please call 1-888-866-5797. Page 6

damp or wet areas.

RECOMMENDED MINIMUM WIRE

GAUGE FOR EXTENSION CORDS*

(120/240 VOLT)

NAMEPLATE

AMPERES

(at full load)

EXTENSION CORD

LENGTH

25’

50’

75’

100’

150’

0 – 2.0 18 18 18 18 16

2.1 – 3.4 18 18 18 16 14

3.5 – 5.0 18 18 16 14 12

5.1 – 7.0 18 16 14 12 12

7.1 – 12.0 18 14 12 10 -

12.1 – 16.0 14 12 10 - -

16.1 – 20.0 12 10 - - -

TABLE A

* Based on limiting the line

voltage drop to ve volts at

150% of the rated amperes.

Symbology

Double Insulated

Canadian Standards Association

Underwriters Laboratories, Inc.

VAC Volts Alternating Current

AAmperes

n0xxxx/min. No Load Revolutions per Minute

(RPM)

Item 62133 For technical questions, please call 1-888-866-5797. Page 7

SPECIFICATIONS

Electrical Requirements 120 VAC, 800 W

Power Cord 115" L, 3-Prong

Grounded

Temperature Range 145° - 432° F

Temperature Setting

Heat

Setting Temperature

Range F Time to Reach

1 145° - 195° 2 Minutes

2 192° - 228° 3 Minutes

3 298° - 367° 3.5 Minutes

4 361° - 432° 4 Minutes

UNPACKING

When unpacking, make sure that

the item is intact and undamaged. If any

parts are missing or broken, please call

Harbor Freight Tools at 1-888-866-5797 as

soon as possible.

OPERATING INSTRUCTIONS

Read the ENTIRE IMPORTANT

SAFETY INFORMATION

section at the beginning of this

manual including all text under

subheadings therein before set

up or use of this product.

Work Piece and Work Area Set Up

1. Designate a work area that is clean

and well-lit. The work area must not

allow access by children or pets to

prevent injury and distraction.

2. Route the power cord along a safe

route to reach the work area without

creating a tripping hazard or exposing

the power cord to possible damage.

The power cord must reach the work

area with enough extra length to

allow free movement while working.

3. There must not be hazardous

objects, such as utility lines or foreign

objects, nearby that will present a

hazard while working.

General Operating Instructions

1. Place the Iron Holder (6) on a flat,

level, non-flammable surface.

2. Wear ANSI-approved safety goggles

and heavy-duty work gloves during

use. Forced-air ventilation may be

required depending on the type of

glue being heated.

3. Turn the Heat Control Knob (8) to the

“OFF” position.

4. Place the Iron securely into the Iron

Holder.

5. Turn the Heat Control Knob to the

setting desired and wait until the Iron

Item 62133 For technical questions, please call 1-888-866-5797. Page 8

reaches the desired temperature.

(See Temperature Setting chart.)

Consult the adhesive tape

manufacturer’s instruction for proper

heat range.

6. Avoid touching the Heat Shield (9)

and Bottom Sole Plate (5) while

plugged in and hot.

7. Try the Iron on a scrap piece of

adhesive tape to test for desired

temperature result.

8. To prevent accidents, turn off the tool

and disconnect its power supply after

use. Allow to cool completely, then

clean and store the tool indoors out of

children’s reach.

Item 62133 For technical questions, please call 1-888-866-5797. Page 9

MAINTENANCE AND

SERVICING

Procedures not specifically

explained in this manual

must be performed only by a

qualified technician.

TO PREVENT

SERIOUS INJURY

FROM ACCIDENTAL

OPERATION:

Turn the Calibration Knob of

the tool to its “OFF” position

and unplug the tool from its

electrical outlet before

performing any inspection,

maintenance, or cleaning

procedures.

Cleaning and Maintenance

1. BEFORE EACH USE, inspect the

general condition of the tool. Check

for loose screws, misalignment or

binding of moving parts, cracked or

broken parts, damaged electrical

wiring, and any other condition that

may affect its safe operation.

2. AFTER USE, clean Bottom Sole

Plate (5) of any glue or adhesive that

may have transferred on by rubbing

on a clean scrap of carpeting while

still hot.

3. Place back on Iron Holder when not

in use.

4. WARNING! If the supply cord

of this tool is damaged, it must

be replaced only by a qualified

service technician.

Item 62133 For technical questions, please call 1-888-866-5797. Page 10

Troubleshooting

Problem Possible Causes Likely Solutions

Tool will not heat

1. No power at outlet.

2. Cord not connected.

3. Heat Control Knob in OFF

position.

1. Check power at outlet.

2. Check that cord is plugged in.

3. Turn Heat Control Knob to a heat setting

position.

Follow all safety precautions whenever diagnosing or servicing the

tool. Disconnect power supply before service.

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY

DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR

DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT

HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS

QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/

OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD

BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE

BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE

ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER

INSTALLATION OF REPLACEMENT PARTS THERETO.

PARTS LIST

Part Description

1 Handle Set w(8) Screws

2Cord Set (Relief Spring, Wire Connection

Clip, two Screws

3Thermostat w/ Extension Post for Control

Knob

4Top Sole Plate w/ve Screws

5 Bottom Sole Plate, Aluminum, Flat

6 Iron Holder

7 Internal Wire Set (2 pieces)

8 Heat Control Knob

9 Heat Shield w/2 Screws and (1) Washer

10 Gasket (Top of heat shield for Handle

Mount)

11 Gasket (Between Heat Shield for top of

Sole Plate)

12 Heating Element

Tabla de contenidos

Otros manuales de Herramientas eléctricas de Chicago Electric

Chicago Electric

Chicago Electric 91674 Manual de usuario

Chicago Electric

Chicago Electric 68857 Instrucciones de montaje

Chicago Electric

Chicago Electric 61423 Manual de usuario

Chicago Electric

Chicago Electric 61687 Manual del operador

Chicago Electric

Chicago Electric Chicago 94560 Manual de instalación

Chicago Electric

Chicago Electric 93213 Manual de instalación

Chicago Electric

Chicago Electric 98912 Manual de instalación

Chicago Electric

Chicago Electric 57226 Instrucciones de montaje

Chicago Electric

Chicago Electric 61778 Instrucciones de montaje

Chicago Electric

Chicago Electric DEMOLITION HAMMER 93853 Manual de instalación

Chicago Electric

Chicago Electric 67537 Manual de usuario

Chicago Electric

Chicago Electric 66001 Manual de instalación

Chicago Electric

Chicago Electric 90287 Manual de usuario

Chicago Electric

Chicago Electric 67707 Manual de instalación

Chicago Electric

Chicago Electric 66098 Manual de instalación

Chicago Electric

Chicago Electric 35778 Manual de usuario

Chicago Electric

Chicago Electric 37793 Manual de instalación

Chicago Electric

Chicago Electric 68696 Instrucciones de montaje

Chicago Electric

Chicago Electric 62422 Instrucciones de montaje

Chicago Electric

Chicago Electric 68821 Manual de usuario

Chicago Electric

Chicago Electric 46935 Manual de instalación

Chicago Electric

Chicago Electric 40208 Manual de usuario

Chicago Electric

Chicago Electric 92880 Manual de instalación

Chicago Electric

Chicago Electric Chicago Electric Power Tools 1600W Heavy Duty Heat... Instrucciones de montaje

Manuales populares de Herramientas eléctricas de otras marcas

AEG

AEG OMNI-JS Manual de usuario

SIP

SIP 01533 Manual de usuario

Ribimex

Ribimex PRS499 Manual de usuario

3M Fiber Optic Connector Crimp Tool Manual de usuario

Ryobi

Ryobi P524 Manual de usuario

ROJEK

ROJEK FSN 300A Manual de usuario

Kemper

Kemper 1740PRO Manual de usuario

WABCO

WABCO OptiTire Manual de usuario

EINHELL

EINHELL TE-MS 18/210 Li Manual de usuario

Orgapack

Orgapack OR-T 85 Guía rápida

TOUGHCUT

TOUGHCUT Diamond 400 Manual de usuario

Yaros

Yaros PB-3603 Manual de usuario

Fein

Fein BSS 2.0 E Guía de configuración

Baileigh Industrial

Baileigh Industrial SS-2725 Manual de usuario

Milwaukee

Milwaukee 2674-20 Manual de usuario

Fein

Fein BLs 1.6 Manual de usuario

Princess

Princess Electric Multi Sharpener Manual de usuario

FOREDOM

FOREDOM K.1050 Manual