Chicago Electric 47937 Manual de usuario

PLUNGE ROUTER - 1HPPLUNGE ROUTER - 1HP

PLUNGE ROUTER - 1HP

VARIABLE SPEEDARIABLE SPEED

ARIABLE SPEEDARIABLE SPEED

ARIABLE SPEED

ASSEMBLY AND OPERATING INSTRUCTIONS

3491 MISSION OAKS BLVD., CAMARILLO, CA 93011

VISIT OUR WEB SITE AT HTTP://WWW.HARBORFREIGHT.COM

this manual or any artwork contained herein may be reproduced in any shape

or form without the express written consent of Harbor Freight Tools.

For technical questions and replacement parts,please call 1-800-444-3353

47937

Page 2

SKU 47937 For technical questions, please call 1-800-444-3353.

SPECIFICATIONS

Item Description

Motor 1 HP, 8.5 Amps

Speed 11,500 to 28,000 RPM (no load);

Variable by rheostat

Power Consumption 110 VAC, 60 Hz, 900 Watts

Power Cord 16 AWG, 2-prong, polarized plug, UL listed

Collet Capacity 1/4 and 5/16 inch

Plunge Depth 2 inches (maximum)

Dust Chute 1-5/8 inches

Weight 7 lbs.

Insert Dimensions 2-1/4 inches

Base Dimensions 6-1/8 (dia.) inches

Overall Dimensions 12 (L) x 6-1/8 (H) x 3/4 (W) inches

SAVE THIS MANUAL

You will need the manual for the safety warnings and precautions, assembly instructions,

operating and maintenance procedures, parts list and diagram. Keep your invoice with this

manual. Write the invoice number on the inside of the front cover. Keep the manual and

invoice in a safe and dry place for future reference.

GENERAL SAFETY RULES

WARNING!

READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to follow all instruc-

tions listed below may result in electric shock, fire, and/or serious injury.

SAVETHESE INSTRUCTIONS

Work Area

1. Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.

2. Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or

fumes.

3. Keep bystanders, children, and visitors away while operating a power tool.

Distractions can cause you to lose control. Protect others in the work area from debris such

as chips and sparks. Provide barriers or shields as needed.

Electrical Safety

4. Grounded tools must be plugged into an outlet properly installed and grounded in

accordance with all codes and ordinances. Never remove the grounding prong or

modify the plug in any way. Do not use any adapter plugs. Check with a qualified

electrician if you are in doubt as to whether the outlet is properly grounded. If the tools

should electrically malfunction or break down, grounding provides a low resistance path to

carry electricity away from the user.

E194601

Page 3

SKU 47937 For technical questions, please call 1-800-444-3353.

5. Double insulated tools are equipped with a polarized plug (one blade is wider

than the other). This plug will fit in a polarized outlet only one way. If the plug

does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a

qualified electrician to install a polarized outlet. Do not change the plug in any

way. Double insulation eliminates the need for the three wire grounded power

cord and grounded power supply system.

6. Avoid body contact with grounded surfaces such as pipes, radiators, ranges,

and refrigerators. There is an increased risk of electric shock if your body is

grounded.

7. Do not expose power tools to rain or wet conditions. Water entering a power tool

will increase the risk of electric shock.

8. Do not abuse the Power Cord. Never use the Power Cord to carry the tools or

pull the Plug from an outlet. Keep the Power Cord away from heat, oil, sharp

edges, or moving parts. Replace damaged Power Cords immediately. Damaged

Power Cords increase the risk of electric shock.

9. When operating a power tool outside, use an outdoor extension cord marked

“W-A” or “W”. These extension cords are rated for outdoor use, and reduce the risk

of electric shock.

Personal Safety

10. Stay alert. Watch what you are doing, and use common sense when operating a

power tool. Do not use a power tool while tired or under the influence of drugs,

alcohol, or medication. A moment of inattention while operating power tools may

result in serious personal injury.

11. Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep

your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or

long hair can be caught in moving parts.

12. Avoid accidental starting. Be sure the Power Switch is off before plugging in.

Carrying power tools with your finger on the Power Switch, or plugging in power tools

with the Power Switch on, invites accidents.

13. Remove adjusting keys or wrenches before turning the power tool on. A wrench

or a key that is left attached to a rotating part of the power tool may result in personal

injury.

14. Do not overreach. Keep proper footing and balance at all times. Proper footing

and balance enables better control of the power tool in unexpected situations.

15. Use safety equipment. Always wear eye protection. Dust mask, non-skid safety

shoes, hard hat, or hearing protection must be used for appropriate conditions.

Page 4

SKU 47937 For technical questions, please call 1-800-444-3353.

Tool Use and Care

16. Use clamps (not included) or other practical ways to secure and support the

workpiece to a stable platform. Holding the work by hand or against your body is

unstable and may lead to loss of control.

17. Do not force the tool. Use the correct tool for your application. The correct tool

will do the job better and safer at the rate for which it is designed.

18. Do not use the power tool if the Power Switch does not turn it on or off. Any tool

that cannot be controlled with the Power Switch is dangerous and must be replaced.

19. Disconnect the Power Cord Plug from the power source before making any

adjustments, changing accessories, or storing the tool. Such preventive safety

measures reduce the risk of starting the tool accidentally.

20. Store idle tools out of reach of children and other untrained persons. Tools are

dangerous in the hands of untrained users.

21. Maintain tools with care. Keep cutting tools sharp and clean. Properly

maintained tools with a sharp cutting edge are less likely to bind and are easier to

control. Do not use a damaged tool. Tag damaged tools “Do not use” until repaired.

22. Check for misalignment or binding of moving parts, breakage of parts, and any

other condition that may affect the tool’s operation. If damaged,have the tool

serviced before using. Many accidents are caused by poorly maintained tools.

23. Use only accessories that are recommended by the manufacturer for your

model. Accessories that may be suitable for one tool may become hazardous when

used on another tool.

Service

24. Tool service must be performed only by qualified repair personnel. Service or

maintenance performed by unqualified personnel could result in a risk of injury.

25. When servicing a tool, use only identical replacement parts. Follow instructions

in the

“Maintenance”

section of this manual. Use of unauthorized parts or failure to

follow maintenance instructions may create a risk of electric shock or injury.

SPECIFIC SAFETY RULES FOR THIS PRODUCT

1. Hold tool by insulated gripping surfaces when performing an operation where

the cutting tool may contact hidden wiring or its own cord. Contact with “live” wire

will make exposed metal parts of the tool “live” and shock the operator.

2. Maintain labels and nameplates on the Plunge Router.These carry important

information. If unreadable or missing, contact Harbor FreightTools for a replacement.

3. Always wear ANSI approved safety impact eye goggles and dust mask when

using the Plunge Router. Using personal safety devices reduce the risk for injury.

Safety impact eye goggles and dust masks are available from Harbor Freight Tools.

Page 5

SKU 47937 For technical questions, please call 1-800-444-3353.

4. Maintain a safe working environment. Keep the work area well lit. Make sure there

is adequate surrounding workspace. Always keep the work area free of obstructions,

grease, oil, trash, and other debris. Do not use a power tool in areas near flammable

chemicals, dusts, and vapors. Do not use this product in a damp or wet location.

5. Avoid unintentional starting. Make sure you are prepared to begin work before

turning on the Plunge Router.

6. Do not force the Plunge Router.This tool will do the work better and safer at the

speed and capacity for which it was designed.

7. Always unplug the Plunge Router from its electrical outlet before performing

and inspection, maintenance, or cleaning procedures.

8. WARNING! Some dust created by power sanding, sawing, grinding, drilling, and

other construction activities, contain chemicals known (to the State of California) to

cause cancer, birth defects or other reproductive harm. Some examples of these

chemicals are: lead from lead-based paints, crystalline silica from bricks and cement

or other masonry products, arsenic and chromium from chemically treated lumber.

Your risk from these exposures varies, depending on how often you do this type of

work. To reduce your exposure to these chemicals: work in a well ventilated area, and

work with approved safety equipment, such as those dust masks that are specially

designed to filter out microscopic particles.

(California Health & Safety Code 25249.5,

et seq.)

9. PACEMAKER SAFETY WARNING! People with pacemakers should consult

their physician(s) before using this product. Electromagnetic fields in close proximity

to a heart pacemaker could cause interference to, or failure of the pacemaker. In

addition, people with pacemakers should adhere to the following:

- Avoid operating power tools alone.

- Don’t use a power tool with the power switch locked on.

- If powered via a power cord be certain that the tool is properly grounded. A ground

fault interrupt (GFCI) system is also a good precaution. This inexpensive device is a

good safety measure because it prevents a sustained electrical shock.

- Properly maintain and inspect all tools before use to avoid electrical shock.

10. Never leave the Plunge Router unattended while running. Turn power off if you

have to leave the Plunge Router.

11. Before each use, check all nuts, bolts,and screws for tightness.Vibration during

mixing may cause these to loosen.

12. Keep extension cord off the ground and away from water.

13. Always connect the Line Cord to a Ground Fault Circuit Interrupter (GFCI)

protected electrical outlet.

14. Do not set the Plunge Router down until the motor comes to a complete stop.

15. Keep fingers, clothing, and hair away from the moving router bit.

Page 6

SKU 47937 For technical questions, please call 1-800-444-3353.

GROUNDING

Note:This tool comes with a two-prong, polarized plug for safety.

WARNING!

Improperly connecting the grounding wire can result in the risk of electric

shock. Check with a qualfified electrician if you are in doubt as to whether the

outlet is properly grounded. Do not modify the power cord plug provided with

the tool.Never remove the grounding prong from the plug. Do not use the tool if

the power cord or plug is damaged. If damaged, have it repaired by a service

facilitybefore use. If the plug willnot fit the outlet,have a properoutlet installed

byaqualifiedelectrician.

Double Insulated Tools: Tools with Two Prong Plugs

1. Tools marked with “Grounding Required” have a three wire cord

and three prong grounding plug. The plug must be connected to a

properly grounded outlet. If the tool should electrically malfunction

or break down, grounding provides a low resistance path to carry

electricity away from the user, reducing the risk of electric shock.

2. The grounding prong in the plug is connected through the green

wire inside the cord to the grounding system in the tool. The

green wire in the cord must be the only wire connected to the tool’s grounding system and

must never be attached to an electrically “live” terminal.

3. Your tool must be plugged into an appropriate outlet, properly installed and grounded in

accordance with all codes and ordinances. The plug and outlet should look like those in the

followingillustration.

4. Tools marked “Double Insulated” do not require grounding.

They have a special double insulation system which satisfies

OSHA requirements and complies with the applicable

standards of Underwriters Laboratories, Inc., the Canadian

Standard Association, and the National Electrical Code. (See

Figure at right.)

5. Double insulated tools may be used in either of the 120 volt

outlets shown in the following illustration.

EXTENSION CORDS

Grounded

tools require a three wire extension cord.

Double Insulated

tools can use

either a two or three wire extension cord.

2. As the distance from the supply outlet increases, you must use a heavier gauge

extension cord. Using extension cords with inadequately sized wire causes a serious

drop in voltage, resulting in loss of power and possible tool damage. (See Table on the

next page.)

Page 7

SKU 47937 For technical questions, please call 1-800-444-3353.

3. The smaller the gauge number of the wire, the greater the capacity of the cord. For

example, a 14 gauge cord can carry a higher current than a 16 gauge cord.(See Table

on the next page.)

4. When using more than one extension cord to make up the total length, make sure

each cord contains at least the minimum wire size required.

5. If you are using one extension cord for more than one tool, add the nameplate

amperes and use the sum to determine the required minimum cord size.

6. If you are using an extension cord outdoors, make sure it is marked with the suffix“W-

A” (“W” in Canada) to indicate it is acceptable for outdoor use.

7. Make sure your extension cord is properly wired and in good electrical condition.

Always replace a damaged extension cord or have it repaired by a qualified electrician

before using it.

8. Protect your extension cords from sharp objects, excessive heat, and damp or wet

areas.

RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS*

(120 VOLT)

NAMEPLATE

AMPERES

(At Full Load)

EXTENSION CORD LENGTH

Feet 50

Feet 75

Feet 100

Feet 150

Feet

0 – 2.0 18 18 18 18 16

2.1 – 3.4 18 18 18 16 14

3.5 – 5.0 18 18 16 14 12

5.1 – 7.0 18 16 14 12 12

7.1 – 12.0 17 14 12 10 -

12.1 – 16.0 14 12 10 - -

16.1 – 20.0 12 10 - - -

* Based on limiting the line voltage drop to five volts at 150% of the rated amperes.

SYMBOLOGY

Page 8

SKU 47937 For technical questions, please call 1-800-444-3353.

UNPACKING

When unpacking, check to make sure that all the parts are included.Refer to the Assembly

section, and the Assembly Drawing and Parts List at the end of this manual.

If any parts are missing or broken, please call Harbor FreightTools at the number on the

cover of this manual as soon as possible.

SETUP AND ADJUSTMENT

Controls and Indicators

Installing Bits

Caution: Before installing accessories or bits, turn the router power Off and unplug the

line cord from the electrical outlet. Bits are sharp. Handle with care. Check the bit for

cracks or damage before using. Use only router bits. Never use a cracked or damaged

bit.

1. Loosen the Plunger Locking Knob (35) to allow the router to raise fully.

2. Press the Collet Lock (23) to keep the shaft stationary.

3. Using Wrench (62), loosen the Collet Nut (27).

4. Insert the bit all the way into the Collet.

5. Using the Wrench, securely tighten Collet Nut while

pushing in on the Collet Lock (23).

Do not tighten the Collet Nut without inserting a bit or

Collet Cone with bit. Damage can occur.

Switch (12)

Lock On Button

Collet Lock (23)

Collet Nut (27)

Lock Knob (31)

Depth Guide

Indicator (42)

Depth Stop

Screws (52)

Handle (33)

Straight Guide

(57)

Lock Knob (44)

for plunge depth

setting Plunger

Locking Lever

(35)

Speed ControlWheel (2)

(27) (23)

Page 9

SKU 47937 For technical questions, please call 1-800-444-3353.

Cutting Depth Adjustment

1. Place the router on a flat surface.

2. Loosen the Plunger Locking Lever (35).

3. Push down on the router Handles (33) until the bit just touches the flat surface.

4. Tighten the Plunger Locking Lever (35).

5. Turn Depth StopTurret (51) to select the desired Screw (52) height.

6. Loosen the Lock Knob (44) holding the Depth Guide Indicator (42), and push down

until it rests on the adjustable Screw (52).

7. Raise the Depth Guide Indicator (42) in fine increments to desired depth of cut as

read on the Scale Guide (14).

Note: The depth of cut is equal to the distance between the end of the Depth Guide

Indicator (42) and the top of the Screw (52) in the Depth StopTurret (51).

8. Loosen the Plunger Locking Lever (35) and lower router body until Depth Guide

Indicator (42) makes contact with the Screw (52). The depth of cut can now be seen.

Placing the Guide Ring and Dust CollectorTube

The Guide Ring (58) is used to make cuts in stock while following around a template.The

Dust Collector Tube (56) must be used with the Guide Ring.

1. Loosen the Plunger Locking Lever (35) to raise the router to its upper position.

2. Without a bit in the Collet (26), angle in the Dust Collection Tube (56) and place it on

the Base (47) seat.See photo below, left.

3. Turn the router on its side and mount the Guide Ring (58) to the Plastic Seat (48) using

Screws (59).The flange projection of the Guide Ring faces outward as shown below,

right.

4. Mount the router (straight) bit through the opening of the Guide Ring (58). Refer to

Installing Bits on the previous page.The bit must not touch the Guide Ring.

5. Adjust the cutting depth, then place the Guide Ring against the edge of the template.

(1)

(56)

(58)

(59) (59)

(48)

Flange

Page 10

SKU 47937 For technical questions, please call 1-800-444-3353.

Note: The cut size may be slightly different from that of the templet.Allow for the distance (Z)

between the router bit and the outside of the Guide Ring (58) by subtracting the bit diameter

size from the Guide Ring (outside diameter), then divide that by 2.

Using the Straight Guide

The Straight Guide (57) with Guide Shafts (54) is used for chamfer or groove cuts.

1. Mount the Guide Shafts (54) to the Straight Guide (57) using Screws (60) and Spring

Washers (61). See photo above, left.

2. Loosen the Lock Knobs (31).

3. Insert Guide Shafts into the holes in the router Base (47). See photo above, right.

4. Adjust the Straight Guide to the desired distance from the bit.

5. Tighten Lock Knobs (31).

6. When cutting, move the router with the Straight Guide flat against the side of the

material to be chamfered or grooved.

Bit Guide Ring (58)

Distance (Z)

Guide Ring Outside Diameter

(61) (60)

(57)

(54)

(31)

(47)

Tabla de contenidos

Otros manuales de Herramientas eléctricas de Chicago Electric

Chicago Electric

Chicago Electric 96298 Manual de usuario

Chicago Electric

Chicago Electric 68861 Manual de usuario

Chicago Electric

Chicago Electric BREAKER HAMMER 94882 Manual de usuario

Chicago Electric

Chicago Electric 46935 Manual de instalación

Chicago Electric

Chicago Electric Chicago 94560 Manual de instalación

Chicago Electric

Chicago Electric 67429 Manual de instalación

Chicago Electric

Chicago Electric 68696 Instrucciones de montaje

Chicago Electric

Chicago Electric Chicago 94560 Manual de usuario

Chicago Electric

Chicago Electric 38437 Manual de usuario

Chicago Electric

Chicago Electric 47269 Guía de referencia rápida

Chicago Electric

Chicago Electric 96289 Manual de instalación

Chicago Electric

Chicago Electric 68848 Manual de usuario

Chicago Electric

Chicago Electric 91674 Manual de usuario

Chicago Electric

Chicago Electric 69343 Instrucciones de montaje

Chicago Electric

Chicago Electric 62133 Instrucciones de montaje

Chicago Electric

Chicago Electric 68221 Instrucciones de montaje

Chicago Electric

Chicago Electric 60428 Manual de usuario

Chicago Electric

Chicago Electric 67631 Manual de instalación

Chicago Electric

Chicago Electric 98912 Manual de instalación

Chicago Electric

Chicago Electric 36W-110V HOT BLADE DECAL REMOVER Manual de instalación

Chicago Electric

Chicago Electric 67632 Manual de instalación

Chicago Electric

Chicago Electric 66182 Manual de instalación

Chicago Electric

Chicago Electric 90672 Manual de usuario

Chicago Electric

Chicago Electric 68221 Manual de usuario

Manuales populares de Herramientas eléctricas de otras marcas

AEG

AEG OMNI-JS Manual de usuario

SIP

SIP 01533 Manual de usuario

Ribimex

Ribimex PRS499 Manual de usuario

3M Fiber Optic Connector Crimp Tool Manual de usuario

Ryobi

Ryobi P524 Manual de usuario

ROJEK

ROJEK FSN 300A Manual de usuario

Kemper

Kemper 1740PRO Manual de usuario

WABCO

WABCO OptiTire Manual de usuario

EINHELL

EINHELL TE-MS 18/210 Li Manual de usuario

Orgapack

Orgapack OR-T 85 Guía rápida

TOUGHCUT

TOUGHCUT Diamond 400 Manual de usuario

Yaros

Yaros PB-3603 Manual de usuario

Fein

Fein BSS 2.0 E Guía de configuración

Baileigh Industrial

Baileigh Industrial SS-2725 Manual de usuario

Milwaukee

Milwaukee 2674-20 Manual de usuario

Fein

Fein BLs 1.6 Manual de usuario

Princess

Princess Electric Multi Sharpener Manual de usuario

FOREDOM

FOREDOM K.1050 Manual